scholarly journals High-resolution velocity measurement in the inner part of turbulent boundary layers over super-hydrophobic surfaces

2016 ◽  
Vol 801 ◽  
pp. 670-703 ◽  
Author(s):  
Hangjian Ling ◽  
Siddarth Srinivasan ◽  
Kevin Golovin ◽  
Gareth H. McKinley ◽  
Anish Tuteja ◽  
...  
Keyword(s):  
Boundary Layer ◽  
Shear Stress ◽  
Velocity Profile ◽  
Drag Reduction ◽  
Slip Velocity ◽  
Reynolds Shear Stress ◽  
Turbulent Boundary Layers ◽  
Mean Velocity ◽  
Roughness Elements ◽  
The Mean

Digital holographic microscopy is used for characterizing the profiles of mean velocity, viscous and Reynolds shear stresses, as well as turbulence level in the inner part of turbulent boundary layers over several super-hydrophobic surfaces (SHSs) with varying roughness/texture characteristics. The friction Reynolds numbers vary from 693 to 4496, and the normalized root mean square values of roughness $(k_{rms}^{+})$ vary from 0.43 to 3.28. The wall shear stress is estimated from the sum of the viscous and Reynolds shear stress at the top of roughness elements and the slip velocity is obtained from the mean profile at the same elevation. For flow over SHSs with $k_{rms}^{+}<1$, drag reduction and an upward shift of the mean velocity profile occur, along with a mild increase in turbulence in the inner part of the boundary layer. As the roughness increases above $k_{rms}^{+}\sim 1$, the flow over the SHSs transitions from drag reduction, where the viscous stress dominates, to drag increase where the Reynolds shear stress becomes the primary contributor. For the present maximum value of $k_{rms}^{+}=3.28$, the inner region exhibits the characteristics of a rough wall boundary layer, including elevated wall friction and turbulence as well as a downward shift in the mean velocity profile. Increasing the pressure in the test facility to a level that compresses the air layer on the SHSs and exposes the protruding roughness elements reduces the extent of drag reduction. Aligning the roughness elements in the streamwise direction increases the drag reduction. For SHSs where the roughness effect is not dominant ($k_{rms}^{+}<1$), the present measurements confirm previous theoretical predictions of the relationships between drag reduction and slip velocity, allowing for both spanwise and streamwise slip contributions.

Scaling of Favorable Pressure Gradient Turbulent Boundary Layers With Eventual Relaminarization

2005 ◽  
Author(s):  
Rau´l Bayoa´n Cal ◽  
Xia Wang ◽  
Luciano Castillo
Keyword(s):  
Boundary Layer ◽  
Pressure Gradient ◽  
Boundary Layers ◽  
Reynolds Shear Stress ◽  
Velocity Profiles ◽  
Turbulent Boundary Layers ◽  
Reynolds Stresses ◽  
Mean Velocity ◽  
Favorable Pressure Gradient ◽  
The Mean

Applying similarity analysis to the RANS equations of motion for a pressure gradient turbulent boundary layer, Castillo and George [1] obtained the scalings for the mean deficit velocity and the Reynolds stresses. Following this analysis, Castillo and George studied favorable pressure gradient (FPG) turbulent boundary layers. They were able to obtain a single curve for FPG flows when scaling the mean deficit velocity profiles. In this study, FPG turbulent boundary layers are analyzed as well as relaminarized boundary layers subjected to an even stronger FPG. It is found that the mean deficit velocity profiles diminish when scaled using the Castillo and George [1] scaling, U∞, and the Zagarola and Smits [2] scaling, U∞δ*/δ. In addition, Reynolds stress data has been analyzed and it is found that the relaminarized boundary layer data decreases drastically in all components of the Reynolds stresses. Furthermore, it will be shown that the shape of the profile for the wall-normal and Reynolds shear stress components change drastically given the relaminarized state. Therefore, the mean velocity deficit profiles as well as Reynolds stresses are found to be necessary in order to understand not only FPG flows, but also relaminarized boundary layers.

Evolution of a moderately short turbulent boundary layer in a severe pressure gradient

1974 ◽  
Vol 64 (4) ◽  
pp. 763-774 ◽  
Author(s):  
R. G. Deissler
Keyword(s):  
Boundary Layer ◽  
Shear Stress ◽  
Turbulent Boundary Layer ◽  
Pressure Gradient ◽  
Reynolds Shear Stress ◽  
Pressure Gradients ◽  
Mean Velocity ◽  
Mass Injection ◽  
The Mean ◽  
Theoretical Results

The early and intermediate development of a highly accelerated (or decelerated) turbulent boundary layer is analysed. For sufficiently large accelerations (or pressure gradients) and for total normal strains which are not excessive, the equation for the Reynolds shear stress simplifies to give a stress that remains approximately constant as it is convected along streamlines. The theoretical results for the evolution of the mean velocity in favourable and adverse pressure gradients agree well with experiment for the cases considered. A calculation which includes mass injection at the wall is also given.

Characteristics of a turbulent boundary layer with an external turbulent uniform shear flow

1976 ◽  
Vol 77 (2) ◽  
pp. 369-396 ◽  
Author(s):  
Q. A. Ahmad ◽  
R. E. Luxton ◽  
R. A. Antonia
Keyword(s):  
Boundary Layer ◽  
Shear Stress ◽  
Shear Flow ◽  
Free Stream ◽  
Reynolds Shear Stress ◽  
Wall Layer ◽  
Turbulence Level ◽  
Mean Velocity ◽  
Free Stream Turbulence ◽  
The Mean

Measurements are presented of both mean and fluctuating velocity components in a turbulent boundary layer subjected to a nearly homogeneous external turbulent shear flow. The Reynolds shear stress in the external shear flow is small compared with the wall shear stress. Its transverse mean velocity gradient λ (≃ 6 s−l) is also small compared with typical gradients based on outer variables (say Uw/δ, where Uwis the value of the linear velocity profile extrapolated to the wall and δ is the boundary-layer thickness), but is of the same order as Ut/δ (Ur is the friction velocity). The influence of both positive and negative transverse velocity gradients on the turbulent wall layer is investigated over a streamwise region where the normal Reynolds stresses in the external flow are approximately equal and constant in the streamwise direction. In this region, the integral length scale of the external flow is of the same order of magnitude as that of the wall layer. Measurements in the boundary layer are also given for an un-sheared external turbulent flow (λ = 0) with a turbulence level Tu of 1.5%, approximately the same as that for h = ± 6 s−1. (Tu, is defined as the ratio of the r.m.s. longitudinal velocity fluctuation to Uw.) The measurements are in good agreement with those available in the literature for a similar free-stream turbulence level and show that the external turbulence level and length scale exert a large influence on the turbulence structure in the boundary layer. The additional effect of the external shear on the mean velocity and turbulent energy budget distributions in the inner region of the boundary layer is found to be small. In the outer region, the ‘wake’ component of the mean velocity defect is lowered by the presence of free-stream turbulence and one extra effect due to the external shear is an increase in the Reynolds shear stress when h is positive and a decrease when h is negative. Another interesting effect due to the shear is the appearance near the edge of the layer of a small but distinct region where the local mean velocity is constant and the Reynolds shear stress is negligible.

Turbulent Boundary Layers on Surfaces Covered With Filamentous Algae

2000 ◽  
Vol 122 (2) ◽  
pp. 357-363 ◽  
Author(s):  
Michael P. Schultz
Keyword(s):  
Boundary Layer ◽  
Shear Stress ◽  
Turbulence Intensity ◽  
Reynolds Shear Stress ◽  
Skin Friction Coefficient ◽  
Laser Doppler Velocimeter ◽  
Mean Velocity ◽  
Rough Walls ◽  
The Mean ◽  
Stress Profiles

Turbulent boundary layer measurements have been made on surfaces covered with filamentous marine algae. These experiments were conducted in a closed return water tunnel using a two-component, laser Doppler velocimeter (LDV). The mean velocity profiles and parameters, as well as the axial and wall-normal turbulence intensities and Reynolds shear stress, are compared with flows over smooth and sandgrain rough walls. Significant increases in the skin friction coefficient for the algae-covered surfaces were measured. The boundary layer and integral thickness length scales were also increased. The results indicate that profiles of the turbulence quantities for the smooth and sandgrain rough walls collapse when friction velocity and boundary layer thickness are used as normalizing parameters. The algae-covered surfaces, however, exhibited a significant increase in the wall-normal turbulence intensity and the Reynolds shear stress, with only a modest increase in the axial turbulence intensity. The peak in the Reynolds shear stress profiles for the algae surfaces corresponded to the maximum extent of outward movement of the algae filaments. [S0098-2202(00)01902-7]

Turbulent Flow Near a Rough Wall

1992 ◽  
Vol 114 (4) ◽  
pp. 537-542 ◽  
Author(s):  
Yang-Moon Koh
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Velocity Profile ◽  
Boundary Layers ◽  
Simple Formula ◽  
Turbulent Boundary Layers ◽  
Mean Velocity ◽  
Friction Factors ◽  
Special Cases ◽  
The Mean

By introducing the equivalent roughness which is defined as the distance from the wall to where the velocity gets a certain value (u/uτ ≈ 8.5) and which can be represented by a simple function of the roughness, a simple formula to represent the mean-velocity distribution across the inner layer of a turbulent boundary layer is suggested. The suggested equation is general enough to be applicable to turbulent boundary layers over surfaces of any roughnesses covering from very smooth to completely rough surfaces. The suggested velocity profile is then used to get expressions for pipe-friction factors and skin friction coefficients. These equations are consistent with existing experimental observations and embrace well-known equations (e.g., Prandtl’s friction law for smooth pipes and Colebrook’s formula etc.) as special cases.

The accelerated fully rough turbulent boundary layer

1977 ◽  
Vol 82 (3) ◽  
pp. 507-528 ◽  
Author(s):  
Hugh W. Coleman ◽  
Robert J. Moffat ◽  
William M. Kays
Keyword(s):  
Boundary Layer ◽  
Shear Stress ◽  
Turbulent Boundary Layer ◽  
Pressure Gradient ◽  
Stress Tensor ◽  
Skin Friction ◽  
Shape Factor ◽  
Reynolds Shear Stress ◽  
Smooth Wall ◽  
Mean Velocity

The behaviour of a fully rough turbulent boundary layer subjected to favourable pressure gradients both with and without blowing was investigated experimentally using a porous test surface composed of densely packed spheres of uniform size. Measurements of profiles of mean velocity and the components of the Reynolds-stress tensor are reported for both unblown and blown layers. Skin-friction coefficients were determined from measurements of the Reynolds shear stress and mean velocity.An appropriate acceleration parameterKrfor fully rough layers is defined which is dependent on a characteristic roughness dimension but independent of molecular viscosity. For a constant blowing fractionFgreater than or equal to zero, the fully rough turbulent boundary layer reaches an equilibrium state whenKris held constant. Profiles of the mean velocity and the components of the Reynolds-stress tensor are then similar in the flow direction and the skin-friction coefficient, momentum thickness, boundary-layer shape factor and the Clauser shape factor and pressure-gradient parameter all become constant.Acceleration of a fully rough layer decreases the normalized turbulent kinetic energy and makes the turbulence field much less isotropic in the inner region (forFequal to zero) compared with zero-pressure-gradient fully rough layers. The values of the Reynolds-shear-stress correlation coefficients, however, are unaffected by acceleration or blowing and are identical with values previously reported for smooth-wall and zero-pressure-gradient rough-wall flows. Increasing values of the roughness Reynolds number with acceleration indicate that the fully rough layer does not tend towards the transitionally rough or smooth-wall state when accelerated.

scholarly journals Global energy fluxes in turbulent channels with flow control

2018 ◽  
Vol 857 ◽  
pp. 345-373 ◽  
Author(s):  
Davide Gatti ◽  
Andrea Cimarelli ◽  
Yosuke Hasegawa ◽  
Bettina Frohnapfel ◽  
Maurizio Quadrio
Keyword(s):  
Reynolds Number ◽  
Shear Stress ◽  
Energy Dissipation ◽  
Velocity Field ◽  
Flow Control ◽  
Reynolds Shear Stress ◽  
Power Input ◽  
Energy Fluxes ◽  
Mean Velocity ◽  
The Mean

This paper addresses the integral energy fluxes in natural and controlled turbulent channel flows, where active skin-friction drag reduction techniques allow a more efficient use of the available power. We study whether the increased efficiency shows any general trend in how energy is dissipated by the mean velocity field (mean dissipation) and by the fluctuating velocity field (turbulent dissipation). Direct numerical simulations (DNS) of different control strategies are performed at constant power input (CPI), so that at statistical equilibrium, each flow (either uncontrolled or controlled by different means) has the same power input, hence the same global energy flux and, by definition, the same total energy dissipation rate. The simulations reveal that changes in mean and turbulent energy dissipation rates can be of either sign in a successfully controlled flow. A quantitative description of these changes is made possible by a new decomposition of the total dissipation, stemming from an extended Reynolds decomposition, where the mean velocity is split into a laminar component and a deviation from it. Thanks to the analytical expressions of the laminar quantities, exact relationships are derived that link the achieved flow rate increase and all energy fluxes in the flow system with two wall-normal integrals of the Reynolds shear stress and the Reynolds number. The dependence of the energy fluxes on the Reynolds number is elucidated with a simple model in which the control-dependent changes of the Reynolds shear stress are accounted for via a modification of the mean velocity profile. The physical meaning of the energy fluxes stemming from the new decomposition unveils their inter-relations and connection to flow control, so that a clear target for flow control can be identified.

Turbulent Boundary Layers Subjected to Multiple Strains

1999 ◽  
Vol 121 (3) ◽  
pp. 526-532 ◽  
Author(s):  
Andreas C. Schwarz ◽  
Michael W. Plesniak ◽  
S. N. B. Murthy
Keyword(s):  
Shear Stress ◽  
Pressure Gradient ◽  
Boundary Layers ◽  
Reynolds Shear Stress ◽  
Turbulent Boundary Layers ◽  
Laser Doppler Velocimeter ◽  
Strain Rates ◽  
The Mean ◽  
Convex Curvature ◽  
Multiple Strain Rates

Turbomachinery flows can be extremely difficult to predict, due to a multitude of effects, including interacting strain rates, compressibility, and rotation. The primary objective of this investigation was to study the influence of multiple strain rates (favorable streamwise pressure gradient combined with radial pressure gradient due to convex curvature) on the structure of the turbulent boundary layer. The emphasis was on the initial region of curvature, which is relevant to the leading edge of a stator vane, for example. In order to gain better insight into the dynamics of complex turbulent boundary layers, detailed velocity measurements were made in a low-speed water tunnel using a two-component laser Doppler velocimeter. The mean and fluctuating velocity profiles showed that the influence of the strong favorable pressure augmented the stabilizing effects of convex curvature. The trends exhibited by the primary Reynolds shear stress followed those of the mean turbulent bursting frequency, i.e., a decrease in the bursting frequency coincided with a reduction of the peak Reynolds shear stress. It was found that the effects of these two strain rates were not superposable, or additive in any simple manner. Thus, the dynamics of the large energy-containing eddies and their interaction with the turbulence production mechanisms must be considered for modeling turbulent flows with multiple strain rates.

Turbulent Vorticity Diffusion in the Stronger Wall Jet Managed by a Flat Plate Wing in the Outer Layer

2015 ◽  
Author(s):  
Takuma Katayama ◽  
Shinsuke Mochizuki
Keyword(s):  
Shear Stress ◽  
Flat Plate ◽  
Outer Layer ◽  
Large Scale ◽  
Reynolds Shear Stress ◽  
Three Dimensional ◽  
Quantitative Relationship ◽  
Wall Jet ◽  
Mean Velocity ◽  
The Mean

The present experiment focuses on the vorticity diffusion in a stronger wall jet managed by a three-dimensional flat plate wing in the outer layer. Measurement of the fluctuating velocities and vorticity correlation has been carried out with 4-wire vorticity probe. The turbulent vorticity diffusion due to the large scale eddies in the outer layer is quantitatively examined by using the 4-wire vorticity probe. Quantitative relationship between vortex structure and Reynolds shear stress is revealed by means of directly measured experimental evidence which explains vorticity diffusion process and influence of the manipulating wing. It is expected that the three-dimensional outer layer manipulator contributes to keep convex profile of the mean velocity, namely, suppression of the turbulent diffusion and entrainment.

Sign in / Sign up

Export Citation Format

Share Document