Numerical study of viscous starting flow past wedges

2016 ◽  
Vol 801 ◽  
pp. 150-165 ◽  
Author(s):  
Ling Xu
Keyword(s):  
Stokes Equations ◽  
Numerical Study ◽  
Similarity Theory ◽  
Vortex Formation ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Flow Past ◽  
Vortex Centre ◽  
Starting Flow ◽  
Vorticity Evolution

This paper presents a numerical study of vortex formation in the impulsively started viscous flow past an infinite wedge, for wedge angles ranging from $60^{\circ }$ to $150^{\circ }$. The Navier–Stokes equations are solved in the vorticity-streamfunction formulation using a time-splitting scheme. The vorticity convection is computed using a semi-Lagrangian method. The vorticity diffusion is computed using an implicit finite difference scheme, after mapping the physical domain conformally onto a rectangle. The results show details of the vorticity evolution and associated streamline and streakline patterns. In particular, a hierarchical formation of recirculating regions corresponding to alternating signs of vorticity is revealed. The appearance times of these vorticity regions of alternate signs, as well as their dependence on the wedge angles, are investigated. The scaling behaviour of the vortex centre trajectory and vorticity is reported, and solutions are compared with those available from laboratory experiments and the inviscid similarity theory.

Flow Past a Forced Oscillating Cylinder: A Three-Dimensional Numerical Study

2019 ◽  
Author(s):  
Huan Ping ◽  
Yan Bao ◽  
Dai Zhou ◽  
Zhaolong Han
Keyword(s):  
Stokes Equations ◽  
Numerical Study ◽  
Three Dimensional ◽  
Flow Dynamics ◽  
Navier Stokes ◽  
Two Dimensional ◽  
Navier Stokes Equations ◽  
Flow Past ◽  
Flow Past A Cylinder ◽  
Two Dimensional Flow

Abstract In this paper, we conducted a three-dimensional investigation of flow past a cylinder undergoing forced oscillation. The flow configuration is similar to the work of Blackburn & Henderson (1999) [1], in which Reynolds number equals to 500 and a fixed motion amplitude of A/D = 0.25. The oscillation frequencies are varied in the range near to the natural shedding frequency of a stationary cylinder. The flow dynamics are governed by Navier-Stokes equations and the solutions are obtained by employing high-order spectral/hp element method. It is found that the flow dynamics are significantly distinguished from the study of two-dimensional flow by Blackburn & Henderson (1999) [1]. The values of hydrodynamic forces are smaller compared to that in the two-dimensional study. However, lock-in boundary we identified is broader. In addition, a different type of hysteresis loop of energy transfer coefficient is obtained.

scholarly journals Dynamics of Single Droplet Splashing on Liquid Film by Coupling FVM with VOF

Processes ◽  
2021 ◽  
Vol 9 (5) ◽  
pp. 841
Author(s):  
Yuzhen Jin ◽  
Huang Zhou ◽  
Linhang Zhu ◽  
Zeqing Li
Keyword(s):  
Liquid Film ◽  
Weber Number ◽  
Stokes Equations ◽  
Numerical Study ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Single Droplet ◽  
Navier Stokes Equations ◽  
Volume Method ◽  
The Relationship

A three-dimensional numerical study of a single droplet splashing vertically on a liquid film is presented. The numerical method is based on the finite volume method (FVM) of Navier–Stokes equations coupled with the volume of fluid (VOF) method, and the adaptive local mesh refinement technology is adopted. It enables the liquid–gas interface to be tracked more accurately, and to be less computationally expensive. The relationship between the diameter of the free rim, the height of the crown with different numbers of collision Weber, and the thickness of the liquid film is explored. The results indicate that the crown height increases as the Weber number increases, and the diameter of the crown rim is inversely proportional to the collision Weber number. It can also be concluded that the dimensionless height of the crown decreases with the increase in the thickness of the dimensionless liquid film, which has little effect on the diameter of the crown rim during its growth.

A numerical study of the interaction between unsteay free-stream disturbances and localized variations in surface geometry

1989 ◽  
Vol 209 ◽  
pp. 285-308 ◽  
Author(s):  
R. J. Bodonyi ◽  
W. J. C. Welch ◽  
P. W. Duck ◽  
M. Tadjfar
Keyword(s):  
Numerical Solutions ◽  
Free Stream ◽  
Stokes Equations ◽  
Numerical Study ◽  
Navier Stokes ◽  
Surface Geometry ◽  
Navier Stokes Equations ◽  
S Waves ◽  
Tollmien Schlichting

A numerical study of the generation of Tollmien-Schlichting (T–S) waves due to the interaction between a small free-stream disturbance and a small localized variation of the surface geometry has been carried out using both finite–difference and spectral methods. The nonlinear steady flow is of the viscous–inviscid interactive type while the unsteady disturbed flow is assumed to be governed by the Navier–Stokes equations linearized about this flow. Numerical solutions illustrate the growth or decay of the T–S waves generated by the interaction between the free-stream disturbance and the surface distortion, depending on the value of the scaled Strouhal number. An important result of this receptivity problem is the numerical determination of the amplitude of the T–S waves.

Numerical Study of Viscous Flows Inside Partially Filled Spinning and Coning Cylinders

1996 ◽  
Vol 118 (2) ◽  
pp. 335-340 ◽  
Author(s):  
Mohamed Selmi
Keyword(s):  
Stokes Equations ◽  
Numerical Study ◽  
Center Of Mass ◽  
Steady Motion ◽  
Practical Interest ◽  
Nonlinear Effects ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Practical Applications ◽  
Analysis And Design

This paper is concerned with the solution of the 3-D-Navier-Stokes equations describing the steady motion of a viscous fluid inside a partially filled spinning and coning cylinder. The cylinder contains either a single fluid of volume less than that of the cylinder or a central rod and a single fluid of combined volume (volume of the rod plus volume of the fluid) equal to that of the cylinder. The cylinder rotates about its axis at the spin rate ω and rotates about an axis that passes through its center of mass at the coning rate Ω. In practical applications, as in the analysis and design of liquid-filled projectiles, the parameter ε = τ sin θ, where τ = Ω/ω and θ is the angle between spin axis and coning axis, is small. As a result, linearization of the Navier-Stokes equations with this parameter is possible. Here, the full and linearized Navier-Stokes equations are solved by a spectral collocation method to investigate the nonlinear effects on the moments caused by the motion of the fluid inside the cylinder. In this regard, it has been found that nonlinear effects are negligible for τ ≈ 0.1, which is of practical interest to the design of liquid-filled projectiles, and the solution of the linearized Navier-Stokes equations is adequate for such a case. However, as τ increases, nonlinear effects increase, and become significant as ε surpasses about 0.1. In such a case, the nonlinear problem must be solved. Complete details on how to solve such a problem is presented.

A 3D Unsteady Flow Analysis in a Doubly Constricted Tube

2000 ◽  
Author(s):  
B. V. Rathish Kumar ◽  
T. Yamaguchi ◽  
H. Liu ◽  
R. Himeno
Keyword(s):  
Pressure Drop ◽  
Unsteady Flow ◽  
Stokes Equations ◽  
Vortex Formation ◽  
Flow Analysis ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
In Series ◽  
3D Unsteady Flow

Abstract Unsteady flow dynamics in a doubly constricted vessel is analyzed by using a time accurate Finite Volume solution of three dimensional incompressible Navier-Stokes equations. Computational experiments are carried out for various values of Reynolds number in order to assess the criticality of multiple mild constrictions in series and also to bring out the subtle 3D features like vortex formation. Studies reveal that pressure drop across a series of mild constrictions can get physiologically critical. Further this pressure drop is found to be sensitive to the spacing between the constrictions and also to the oscillatory nature of the inflow profile.

Experimental and Numerical Study of Vortex Induced Vibrations on a Spool Model

2018 ◽  
Author(s):  
David Gross ◽  
Yann Roux ◽  
Benjamin Rousse ◽  
François Pétrié ◽  
Ludovic Assier ◽  
...  
Keyword(s):  
Stokes Equations ◽  
Numerical Study ◽  
Fluid Dynamic ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Flow Perturbation ◽  
Industry Standards ◽  
Vortex Induced Vibrations ◽  
Recommended Practices ◽  
Decay Tests

The problem of Vortex-Induced Vibrations (VIV) on spool and jumper geometries is known to present several drawbacks when approached with conventional engineering tools used in the study of VIV on risers. Current recommended practices can lead to over-conservatism that the industry needs to quantify and minimize within notably cost reduction objectives. Within this purpose, the paper will present a brief critical review of the Industry standards and more particularly focus on both experimental and Computational Fluid Dynamic (CFD) approaches. Both qualitative and quantitative comparisons between basin tests and CFD results for a 2D ‘M-shape’ spool model will be detailed. The results presented here are part of a larger experimental and numerical campaign which considered a number of current velocities, heading and geometry configurations. The vibratory response of the model will be investigated for one of the current velocities and compared with the results obtained through recommended practices (e.g. Shear7 and DNV guidelines). The strategy used by the software K-FSI to solve the fluid-structure interaction (FSI) problem is a partitioned coupling solver between fluid solver (FINE™/Marine) and structural solvers (ARA). FINE™/Marine solves the Reynolds-Averaged Navier-Stokes Equations in a conservative way via the finite volume method and can work on structured or unstructured meshes with arbitrary polyhedrons, while ARA is a nonlinear finite element solver with a large displacement formulation. The experiments were conducted in the BGO FIRST facility located in La Seyne sur Mer, France. Particular attention was paid towards the model design, fabrication, instrumentation and characterization, to ensure an excellent agreement between the structural numerical model and the actual physical model. This included the use of a material with low structural damping, the performance of stiffness and decay tests in air and in still water, plus the rationalization of the instrumentation to be able to capture the response with the minimum flow perturbation or interaction due to instrumentation.

Numerical Prediction of Turbulent Wakes Behind a Square Cylinder

1998 ◽  
Vol 14 (1) ◽  
pp. 23-29
Author(s):  
Robert R. Hwang ◽  
Sheng-Yuh Jaw
Keyword(s):  
Stokes Equations ◽  
Numerical Study ◽  
Navier Stokes ◽  
Wall Region ◽  
Square Cylinder ◽  
Mean Velocity ◽  
Navier Stokes Equations ◽  
Turbulent Vortex Shedding ◽  
Model Equations ◽  
Good Agreement

ABSTRACTThis paper presents a numerical study on turbulent vortex shedding flows past a square cylinder. The 2D unsteady periodic shedding motion was resolved in the calculation and the superimposed turbulent fluctuations were simulated with a second-order Reynolds-stress closure model. The calculations were carried out by solving numerically the fully elliptic ensemble-averaged Navier-Stokes equations coupled with the turbulence model equations together with the two-layer approach in the treatment of the near-wall region. The performance of the computations was evaluated by comparing the numerical results with data from available experiments. Results indicate that the present study gives good agreement in the shedding frequency and mean drag as well as in some phase profiles of the mean velocity.

Sign in / Sign up

Export Citation Format

Share Document