Interlayer interaction and mechanical properties in multi-layer graphene, Boron-Nitride, Aluminum-Nitride and Gallium-Nitride graphene-like structure: A quantum-mechanical DFT study

2017 ◽  
Vol 112 ◽  
pp. 30-45 ◽  
Author(s):  
Morteza Ghorbanzadeh Ahangari ◽  
A. Fereidoon ◽  
Amin Hamed Mashhadzadeh
Keyword(s):  
Mechanical Properties ◽  
Gallium Nitride ◽  
Boron Nitride ◽  
Aluminum Nitride ◽  
Dft Study ◽  
Quantum Mechanical ◽  
Interlayer Interaction ◽  
Layer Graphene

Cathodoluminescence of Praseodymium doped AlN, GaN and turbo static BN.

2004 ◽  
Vol 831 ◽  
Author(s):  
Muhammad Maqbool ◽  
H. H. Richardson ◽  
M. E. Kordesch
Keyword(s):  
Thin Films ◽  
Gallium Nitride ◽  
Boron Nitride ◽  
Aluminum Nitride ◽  
Room Temperature ◽  
Reactive Sputtering ◽  
Visible Range ◽  
Rf Power

ABSTRACTPraseodymium (Pr) doped aluminum nitride (AlN), gallium nitride (GaN) and boron nitride (BN) thin films deposited on Si (111) substrate are studied with cathodoluminescence. AlN:Pr and GaN:Pr films are deposited at 77 K and room temperature respectively while BN:Pr films at 750 K by reactive sputtering, using 100–200 Watts RF power, 5–10 mTorr nitrogen. Metal targets of Al and B with Pr and a liquid target of Ga with solid Pr are used. The dominant peaks observed in the visible range result from 3P0 → 3H4, 3P1→ 3H5, and 3P0 → 3F2 transitions in AlN:Pr, 3P0 → 3H4, 3P0 → 3H6, and 3P0 → 3F2 transitions in GaN:Pr and from 3P0 → 3H4, 3P1→ 3H5, 3P0 → 3H6, and 3P0 → 3F2 transitions in BN:Pr. Additional peaks are observed from AlN:Pr at 335 nm and 385 nm from 1S0 → 1D2 and 1S0 → 1I6 which are not observed in GaN:Pr and BN:Pr films.

Structure and properties of compact articles from high-alloyed iron powder with adding of boron nitride

2020 ◽  
pp. 39-48
Author(s):  
B. O. Bolshakov ◽  
◽  
R. F. Galiakbarov ◽  
A. M. Smyslov ◽  
◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Boron Nitride ◽  
Grain Boundary ◽  
Bending Strength ◽  
Physical And Mechanical Properties ◽  
Operating Conditions ◽  
Structure And Properties ◽  
Steam Turbines ◽  
Friction Forces ◽  
Wide Range

The results of the research of structure and properties of a composite compact from 13 Cr – 2 Мо and BN powders depending on the concentration of boron nitride are provided. It is shown that adding boron nitride in an amount of more than 2% by weight of the charge mixture leads to the formation of extended grain boundary porosity and finely dispersed BN layers in the structure, which provides a high level of wearing properties of the material. The effect of boron nitride concentration on physical and mechanical properties is determined. It was found that the introduction of a small amount of BN (up to 2 % by weight) into the compacts leads to an increase in plasticity, bending strength, and toughness by reducing the friction forces between the metal powder particles during pressing and a more complete grain boundary diffusion process during sintering. The formation of a regulated structure-phase composition of powder compacts of 13 Cr – 2 Mо – BN when the content of boron nitride changes in them allows us to provide the specified physical and mechanical properties in a wide range. The obtained results of studies of the physical and mechanical characteristics of the developed material allow us to reasonably choose the necessary composition of the powder compact for sealing structures of the flow part of steam turbines, depending on their operating conditions.

Boron nitride for modification of rubber based on isoprene elastomer

2020 ◽  
pp. 105-112
Author(s):  
K. S. Zhansakova ◽  
E. N. Eremin ◽  
G. S. Russkikh ◽  
O. V. Kropotin
Keyword(s):  
Mechanical Properties ◽  
Boron Nitride ◽  
Gradual Increase ◽  
Physical And Mechanical Properties ◽  
Curing Time ◽  
Cross Link ◽  
Start Time ◽  
Link Density ◽  
Cross Link Density ◽  
Isoprene Rubber

The work studies vulcanization characteristics of elastomers based on isoprene rubber filled with carbon black N330 and boron nitride (BN). The influence of the boron nitride (BN) concentration on technological, dynamic, physical and mechanical properties of elastomers has been researched. The application of boron nitride for producing rubber with good properties has been considered. With a gradual increase of the inert filler BN concentration up to 35%, a decrease in the curing rate by 33% and polymer cross-link density by 26% is observed. Moreover, the start time of vulcanization increases by almost 300%, the optimal curing time by 200%.

Electro-mechanical properties of multilayered aluminum nitride and platinum thin films at high temperatures

2019 ◽  
Vol 293 ◽  
pp. 128-135 ◽  
Author(s):  
P. Schmid ◽  
F. Triendl ◽  
C. Zarfl ◽  
S. Schwarz ◽  
W. Artner ◽  
...  
Keyword(s):  
Thin Films ◽  
Mechanical Properties ◽  
Aluminum Nitride ◽  
High Temperatures
Sign in / Sign up

Export Citation Format

Share Document