High hardness dual-phase high entropy alloy thin films produced by interface alloying

2019 ◽  
Vol 162 ◽  
pp. 281-285 ◽  
Author(s):  
Y.P. Cai ◽  
G.J. Wang ◽  
Y.J. Ma ◽  
Z.H. Cao ◽  
X.K. Meng
Keyword(s):  
Thin Films ◽  
High Hardness ◽  
High Entropy Alloy ◽  
Dual Phase ◽  
High Entropy

scholarly journals High Strength and Deformation Mechanisms of Al0.3CoCrFeNi High-Entropy Alloy Thin Films Fabricated by Magnetron Sputtering

Entropy ◽  
2019 ◽  
Vol 21 (2) ◽  
pp. 146 ◽  
Author(s):  
Wei-Bing Liao ◽  
Hongti Zhang ◽  
Zhi-Yuan Liu ◽  
Pei-Feng Li ◽  
Jian-Jun Huang ◽  
...  
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Magnetron Sputtering ◽  
High Hardness ◽  
Deformation Mechanisms ◽  
High Entropy Alloy ◽  
Alloy Thin Film ◽  
Face Centered Cubic ◽  
High Entropy ◽  
Strength And Deformation

Recently, high-entropy alloy thin films (HEATFs) with nanocrystalline structures and high hardness were developed by magnetron sputtering technique and have exciting potential to make small structure devices and precision instruments with sizes ranging from nanometers to micrometers. However, the strength and deformation mechanisms are still unclear. In this work, nanocrystalline Al0.3CoCrFeNi HEATFs with a thickness of ~4 μm were prepared. The microstructures of the thin films were comprehensively characterized, and the mechanical properties were systematically studied. It was found that the thin film was smooth, with a roughness of less than 5 nm. The chemical composition of the high entropy alloy thin film was homogeneous with a main single face-centered cubic (FCC) structure. Furthermore, it was observed that the hardness and the yield strength of the high-entropy alloy thin film was about three times that of the bulk samples, and the plastic deformation was inhomogeneous. Our results could provide an in-depth understanding of the mechanics and deformation mechanism for future design of nanocrystalline HEATFs with desired properties.

scholarly journals An advancement in the synthesis of unique soft magnetic CoCuFeNiZn high entropy alloy thin films

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Chokkakula L. P. Pavithra ◽  
Reddy Kunda Siri Kiran Janardhana ◽  
Kolan Madhav Reddy ◽  
Chandrasekhar Murapaka ◽  
Joydip Joardar ◽  
...  
Keyword(s):  
Thin Films ◽  
Saturation Magnetization ◽  
Functional Materials ◽  
Single Step ◽  
High Entropy Alloy ◽  
High Saturation Magnetization ◽  
Soft Magnetic ◽  
High Entropy ◽  
High Saturation ◽  
Electrochemical Approach

AbstractDiscovery of advanced soft-magnetic high entropy alloy (HEA) thin films are highly pursued to obtain unidentified functional materials. The figure of merit in current nanocrystalline HEA thin films relies in integration of a simple single-step electrochemical approach with a complex HEA system containing multiple elements with dissimilar crystal structures and large variation of melting points. A new family of Cobalt–Copper–Iron–Nickel–Zinc (Co–Cu–Fe–Ni–Zn) HEA thin films are prepared through pulse electrodeposition in aqueous medium, hosts nanocrystalline features in the range of ~ 5–20 nm having FCC and BCC dual phases. The fabricated Co–Cu–Fe–Ni–Zn HEA thin films exhibited high saturation magnetization value of ~ 82 emu/g, relatively low coercivity value of 19.5 Oe and remanent magnetization of 1.17%. Irrespective of the alloying of diamagnetic Zn and Cu with ferromagnetic Fe, Co, Ni elements, the HEA thin film has resulted in relatively high saturation magnetization which can provide useful insights for its potential unexplored applications.

Laser Assisted High Entropy Alloy Coating on Low Carbon Steel

2019 ◽  
Vol 813 ◽  
pp. 159-164
Author(s):  
Carlos Alberto Souto ◽  
Gustavo Faria Melo da Silva ◽  
Laura Angelica Ardila Rodriguez ◽  
Aline C. de Oliveira ◽  
Kátia Regina Cardoso
Keyword(s):  
Wear Resistance ◽  
Carbon Steel ◽  
Low Carbon Steel ◽  
High Hardness ◽  
Alloy Coating ◽  
High Entropy Alloy ◽  
Nominal Composition ◽  
Low Carbon ◽  
High Entropy ◽  
Scan Speed

Coatings with high entropy alloys of the AlCoCrFeNiV system were obtained by selective laser melting on low carbon steel substrates. The effect of the variation of the Fe and V contents as well as the laser processing parameters in the development of the coating were evaluated. The coatings were obtained from the simple powder mixtures of the high purity elemental components in a planetary ball mill. The coatings were obtained by using CO2 laser with a power of 100 W, diameter of 0.16 mm, and scan speed varying from 3 to 12 mm/s. Phase constituents, microstructure and hardness were investigated by XRD, SEM, and microhardness tester, respectively. Wear resistance measurements were carried out by the micro-abrasion method using ball-cratering tests. The coatings presented good adhesion to the substrate and high hardness, of the order of 480 to 650 HV. Most homogeneous coating with nominal composition was obtained by using the higher scan speed, 12 mm/s. Vanadium addition increased hardness and gave rise to a high entropy alloy coating composed by BCC solid solutions. Ball cratering tests conducted on HEA layer showing improvement of material wear resistance, when compared to base substrate, decreasing up to 88% its wear rate, from 1.91x10-6 mm3/Nmm to 0.23x10-6 mm3/Nmm.

Electrochemical deposition and microstructural characterization of AlCrFeMnNi and AlCrCuFeMnNi high entropy alloy thin films

2015 ◽  
Vol 358 ◽  
pp. 533-539 ◽  
Author(s):  
V. Soare ◽  
M. Burada ◽  
I. Constantin ◽  
D. Mitrică ◽  
V. Bădiliţă ◽  
...  
Keyword(s):  
Thin Films ◽  
Electrochemical Deposition ◽  
Microstructural Characterization ◽  
High Entropy Alloy ◽  
High Entropy

Microstructure and compression properties of a dual-phase FeCoCrMn high-entropy alloy

2021 ◽  
Author(s):  
Lijing Lin ◽  
Xin Xian ◽  
Zhihong Zhong ◽  
Kuijing Song ◽  
Chengyong Wang ◽  
...  
Keyword(s):  
High Entropy Alloy ◽  
Dual Phase ◽  
High Entropy ◽  
Compression Properties

Chemical evolution-induced strengthening on AlCoCrNi dual-phase high-entropy alloy with high specific strength

2019 ◽  
Vol 777 ◽  
pp. 828-834 ◽  
Author(s):  
Elyorjon Jumaev ◽  
Sung Hwan Hong ◽  
Jeong Tae Kim ◽  
Hae Jin Park ◽  
Young Seok Kim ◽  
...  
Keyword(s):  
Chemical Evolution ◽  
High Entropy Alloy ◽  
Dual Phase ◽  
High Entropy ◽  
Specific Strength ◽  
High Specific Strength

scholarly journals Enhanced Wear Behaviour of Spark Plasma Sintered AlCoCrFeNiTi High-Entropy Alloy Composites

Materials ◽  
2018 ◽  
Vol 11 (11) ◽  
pp. 2225 ◽  
Author(s):  
Martin Löbel ◽  
Thomas Lindner ◽  
Thomas Lampke
Keyword(s):  
Wear Resistance ◽  
High Hardness ◽  
Solid Lubricants ◽  
Wear Behaviour ◽  
High Entropy Alloy ◽  
Surface Protection ◽  
High Entropy ◽  
Production Route ◽  
The Coefficient Of Friction ◽  
Spark Plasma

High hardness and good wear resistance have been revealed for the high-entropy alloy (HEA) system AlCoCrFeNiTi, confirming the potential for surface protection applications. Detailed studies to investigate the microstructure and phase formation have been carried out using different production routes. Powder metallurgical technologies allow for much higher flexibility in the customisation of materials compared to casting processes. Particularly, spark plasma sintering (SPS) enables the fast processing of the feedstock, the suppression of grain coarsening and the production of samples with a low porosity. Furthermore, solid lubricants can be incorporated for the improvement of wear resistance and the reduction of the coefficient of friction (COF). This study focuses on the production of AlCoCrFeNiTi composites comprising solid lubricants. Bulk materials with a MoS2 content of up to 15 wt % were produced. The wear resistance and COF were investigated in detail under sliding wear conditions in ball-on-disk tests at room temperature and elevated temperature. At least 10 wt % of MoS2 was required to improve the wear behaviour in both test conditions. Furthermore, the effects of the production route and the content of solid lubricant on microstructure formation and phase composition were investigated. Two major body-centred cubic (bcc) phases were detected in accordance with the feedstock. The formation of additional phases indicated the decomposition of MoS2.

scholarly journals High-pressure preparation of high-hardness CoCrFeNiMo0.4 high-entropy alloy

2021 ◽  
pp. 105718
Author(s):  
Yulin Qin ◽  
Yipeng Wang ◽  
Shixue Guan ◽  
Chuqi Wang ◽  
Bo Jiang ◽  
...  
Keyword(s):  
High Pressure ◽  
High Hardness ◽  
High Entropy Alloy ◽  
High Entropy

scholarly journals Synthesis of high-entropy alloy thin films via grain boundary diffusion–assisted solid-state alloying

2022 ◽  
Vol 207 ◽  
pp. 114302
Author(s):  
Seungjin Nam ◽  
Sang Jun Kim ◽  
Moon J. Kim ◽  
Manuel Quevedo-Lopez ◽  
Jun Yeon Hwang ◽  
...  
Keyword(s):  
Thin Films ◽  
Solid State ◽  
Grain Boundary ◽  
Boundary Diffusion ◽  
Grain Boundary Diffusion ◽  
High Entropy Alloy ◽  
High Entropy
Sign in / Sign up

Export Citation Format

Share Document