Fully recrystallized nanostructure fabricated without severe plastic deformation in high-Mn austenitic steel

2013 ◽  
Vol 68 (10) ◽  
pp. 813-816 ◽  
Author(s):  
Rajib Saha ◽  
Rintaro Ueji ◽  
Nobuhiro Tsuji
Keyword(s):  
Plastic Deformation ◽  
Severe Plastic Deformation ◽  
Austenitic Steel

Reversible Martensitic Transformation Produced by Severe Plastic Deformation of Metastable Austenitic Steel

2013 ◽  
Vol 738-739 ◽  
pp. 491-495 ◽  
Author(s):  
Igor Litovchenko ◽  
Alexander Tyumentsev ◽  
Alexander V. Korznikov
Keyword(s):  
Plastic Deformation ◽  
High Pressure ◽  
Martensitic Transformation ◽  
Severe Plastic Deformation ◽  
Dynamic Recrystallization ◽  
Austenitic Steel ◽  
High Pressure Torsion ◽  
Martensitic Transformations ◽  
Metastable Austenitic Steel ◽  
Nanostructured States

The peculiarities of martensitic transformations and formation of nanostructured states in metastable austenitic steel (Fe-18Cr-8Ni-Ti) after severe plastic deformation by high pressure torsion are investigated. It is shown that during severe plastic deformation with increased strain rate not only direct (γ→α΄) but also reverse (α΄→γ) martensitic transformations occur, which is revealed by the changes in the volume content of α΄ - martensite during deformation. The fragments thought to be formed by direct and reverse martensitic transformations and those of dynamic recrystallization of austenite are observed.

Severe plastic deformation of Al-1%Cu Alloy processed by a Simple Cyclic Extrusion Compression technique

2018 ◽  
Vol 1 (1) ◽  
pp. 77-90
Author(s):  
Walaa Abdelaziem ◽  
Atef Hamada ◽  
Mohsen A. Hassan
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Severe Plastic Deformation ◽  
Deformation Behavior ◽  
Cast Alloy ◽  
Surface Hardness ◽  
Grain Structure ◽  
Compression Technique ◽  
Cu Alloy ◽  
Cyclic Extrusion Compression

Severe plastic deformation is an effective method for improving the mechanical properties of metallic alloys through promoting the grain structure. In the present work, simple cyclic extrusion compression technique (SCEC) has been developed for producing a fine structure of cast Al-1 wt. % Cu alloy and consequently enhancing the mechanical properties of the studied alloy. It was found that the grain structure was significantly reduced from 1500 µm to 100 µm after two passes of cyclic extrusion. The ultimate tensile strength and elongation to failure of the as-cast alloy were 110 MPa and 12 %, respectively. However, the corresponding mechanical properties of the two pass CEC deformed alloy are 275 MPa and 35%, respectively. These findings ensure that a significant improvement in the grain structure has been achieved. Also, cyclic extrusion deformation increased the surface hardness of the alloy by 49 % after two passes. FE-simulation model was adopted to simulate the deformation behavior of the material during the cyclic extrusion process using DEFORMTM-3D Ver11.0. The FE-results revealed that SCEC technique was able to impose severe plastic strains with the number of passes. The model was able to predict the damage, punch load, back pressure, and deformation behavior.

TECHNOLOGIES FOR MANUFACTURING NANOSTRUCTURED SURFACES

2020 ◽  
Author(s):  
Андрей Дмитриевич Бухтеев ◽  
Виктория Буянтуевна Бальжиева ◽  
Анна Романовна Тарасова ◽  
Фидан Гасанова ◽  
Светлана Викторовна Агасиева
Keyword(s):  
Plastic Deformation ◽  
Surface Modification ◽  
Severe Plastic Deformation ◽  
Pressing Pressure ◽  
Pressure Treatment ◽  
Structured Surfaces ◽  
Nanostructured Surfaces ◽  
Angular Pressing ◽  
Multilayer Composites ◽  
Compaction Of Powders

В данной статье рассматривается применение и технологии получения наноструктурированных поверхностей. Рассмотрены такие методы как компактирование порошков (изостатическое прессование, метод Гляйтера), интенсивная пластическая деформация (угловое кручение, равноканальное угловое прессование, обработка давлением многослойных композитов) и модификация поверхности (лазерная обработка, ионная бомбардировка). This article discusses the application and technology for obtaining nano-structured surfaces. Methods such as compaction of powders (isostatic pressing, Gleiter method), severe plastic deformation (angular torsion, equal-channel angular pressing, pressure treatment of multilayer composites) and surface modification (laser treatment, ion bombardment) are considered.

Sign in / Sign up

Export Citation Format

Share Document