Water vapor and CO2 transport through amine-containing facilitated transport membranes

2015 ◽  
Vol 86 ◽  
pp. 111-116 ◽  
Author(s):  
Zi Tong ◽  
Varun K. Vakharia ◽  
Michael Gasda ◽  
W.S. Winston Ho
Keyword(s):  
Water Vapor ◽  
Facilitated Transport ◽  
Co2 Transport

scholarly journals Effect of Mobile Carrier on the Performance of PVAm–Nanocellulose Facilitated Transport Membranes for CO2 Capture

Membranes ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 442
Author(s):  
Riccardo Casadei ◽  
Elham Firouznia ◽  
Marco Giacinti Baschetti
Keyword(s):  
Relative Humidity ◽  
Water Uptake ◽  
Co2 Capture ◽  
Water Sorption ◽  
Facilitated Transport ◽  
Gas Permeation ◽  
High Relative Humidity ◽  
Co2 Transport ◽  
Mobile Carrier

Facilitated transport membranes obtained by coupling polyvinylamine with highly charged carboxymethylated nanocellulose fibers were studied considering both water sorption and gas permeation experiments. In particular, the effect of the L-arginine as a mobile carrier was investigated to understand possible improvements in CO2 transport across the membranes. The results show that L-arginine addition decreases the water uptake of the membrane, due to the lower polyvinylamine content, but was able to improve the CO2 transport. Tests carried on at 35 °C and high relative humidity indeed showed an increase of both CO2 permeability and selectivity with respect to nitrogen and methane. In particular, the CO2 permeability increased from 160 to about 340 Barrer when arginine loading was increased from 0 to 45 wt%. In the same conditions, selectivity with respect to nitrogen was more than doubled, increasing from 20 to 45. Minor improvements were instead obtained with respect to methane; CO2/CH4 selectivity, indeed, even in presence of the mobile carrier, was limited to about 20.

New Design for a Differentially Pumped Hydration Chamber for a Siemens IA

1971 ◽  
Vol 29 ◽  
pp. 44-45
Author(s):  
R. C. Moretz ◽  
G. G. Hausner ◽  
D. F. Parsons
Keyword(s):  
Electron Microscopy ◽  
Water Vapor ◽  
Electron Diffraction ◽  
Water Vapor Pressure ◽  
Biological Materials ◽  
Thin Membrane ◽  
Reliable System ◽  
System A ◽  
Water Films ◽  
Aperture Opening

Electron microscopy and diffraction of biological materials in the hydrated state requires the construction of a chamber in which the water vapor pressure can be maintained at saturation for a given specimen temperature, while minimally affecting the normal vacuum of the remainder of the microscope column. Initial studies with chambers closed by thin membrane windows showed that at the film thicknesses required for electron diffraction at 100 KV the window failure rate was too high to give a reliable system. A single stage, differentially pumped specimen hydration chamber was constructed, consisting of two apertures (70-100μ), which eliminated the necessity of thin membrane windows. This system was used to obtain electron diffraction and electron microscopy of water droplets and thin water films. However, a period of dehydration occurred during initial pumping of the microscope column. Although rehydration occurred within five minutes, biological materials were irreversibly damaged. Another limitation of this system was that the specimen grid was clamped between the apertures, thus limiting the yield of view to the aperture opening.

Hydration Chamber for Jeolco 200 Kv Microscope

1970 ◽  
Vol 28 ◽  
pp. 542-543
Author(s):  
V. R. Matricardi ◽  
G. G. Hausner ◽  
D. F. Parsons
Keyword(s):  
Electron Microscope ◽  
Water Vapor ◽  
Vapor Pressure ◽  
Pressure Gradient ◽  
Room Temperature ◽  
List Type ◽  
Type Number ◽  
Equilibrium Vapor Pressure

In order to observe room temperature hydrated specimens in an electron microscope, the following conditions should be satisfied: The specimen should be surrounded by water vapor as close as possible to the equilibrium vapor pressure corresponding to the temperature of the specimen.The specimen grid should be inserted, focused and photo graphed in the shortest possible time in order to minimize dehydration.The full area of the specimen grid should be visible in order to minimize the number of changes of specimen required.There should be no pressure gradient across the grid so that specimens can be straddled across holes.Leakage of water vapor to the column should be minimized.

Warm and freeze-fracture of cotton seed radicles

1987 ◽  
Vol 45 ◽  
pp. 984-985
Author(s):  
E. L. Vigil ◽  
E. F. Erbe
Keyword(s):  
Thin Film ◽  
Water Vapor ◽  
Fracture Surface ◽  
Membrane Structure ◽  
Room Temperature ◽  
Freeze Fracture ◽  
Longitudinal Axis ◽  
Fracture Plane ◽  
Cotton Seeds ◽  
Condensed Water

In cotton seeds the radicle has 12% moisture content which makes it possible to prepare freeze-fracture replicas without fixation or cryoprotection. For this study we have examined replicas of unfixed radicle tissue fractured at room temperature to obtain data on organelle and membrane structure.Excised radicles from seeds of cotton (Gossyplum hirsutum L. M-8) were fractured at room temperature along the longitudinal axis. The fracture was initiated by spliting the basal end of the excised radicle with a razor. This procedure produced a fracture through the tissue along an unknown fracture plane. The warm fractured radicle halves were placed on a thin film of 100% glycerol on a flat brass cap with fracture surface up. The cap was rapidly plunged into liquid nitrogen and transferred to a freeze- etch unit. The sample was etched for 3 min at -95°C to remove any condensed water vapor and then cooled to -150°C for platinum/carbon evaporation.

LINE SHAPE PARAMETERS OF WATER VAPOR TRANSITIONS IN THE 3645-3975 cm−1 REGION

2017 ◽  
Author(s):  
Mary Smith ◽  
Thomas Blake ◽  
Robert Sams ◽  
Candice Renaud ◽  
Bastien Vispoel ◽  
...  
Keyword(s):  
Water Vapor ◽  
Line Shape ◽  
Shape Parameters
Sign in / Sign up

Export Citation Format

Share Document