scholarly journals Effects of differential diffusion on nonpremixed-flame temperature

2019 ◽  
Vol 37 (2) ◽  
pp. 1757-1766 ◽  
Author(s):  
A. Almagro ◽  
O. Flores ◽  
M. Vera ◽  
A. Liñán ◽  
A.L. Sánchez ◽  
...  
Keyword(s):  
Flame Temperature ◽  
Differential Diffusion ◽  
Nonpremixed Flame

Electron microscopy studies of plasma-sprayed materials

1983 ◽  
Vol 41 ◽  
pp. 70-71
Author(s):  
K.R. Subramanian ◽  
A.H. King ◽  
H. Herman
Keyword(s):  
Plasma Spraying ◽  
Substrate Surface ◽  
Flame Temperature ◽  
Ceramic Coatings ◽  
Metallic Substrates ◽  
Hot Plasma ◽  
Almost All ◽  
Plasma Sprayed ◽  
Hostile Environments ◽  
Plasma Spraying Process

Plasma spraying is a technique which is used to apply coatings to metallic substrates for a variety of purposes, including hardfacing, corrosion resistance and thermal barrier applications. Almost all of the applications of this somewhat esoteric fabrication technique involve materials in hostile environments and the integrity of the coatings is of paramount importance: the effects of process variables on such properties as adhesive strength, cohesive strength and hardness of the substrate/coating system, however, are poorly understood.Briefly, the plasma spraying process involves forming a hot plasma jet with a maximum flame temperature of approximately 20,000K and a gas velocity of about 40m/s. Into this jet the coating material is injected, in powder form, so it is heated and projected at the substrate surface. Relatively thick metallic or ceramic coatings may be speedily built up using this technique.

scholarly journals Research on the Ignition Height and Reaction Flame Temperature of PTFE/Al/Si/CuO with Different Mass Ratios of PTFE/Si

Materials ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3464
Author(s):  
Xuan Zou ◽  
Jingyuan Zhou ◽  
Xianwen Ran ◽  
Yiting Wu ◽  
Ping Liu ◽  
...  
Keyword(s):  
Energy Release ◽  
High Speed ◽  
Flame Temperature ◽  
Sintering Process ◽  
Release Process ◽  
Reactive Material ◽  
Temperature Changes ◽  
Release Capacity ◽  
Mass Ratios ◽  
The Relationship

Recent studies have shown that the energy release capacity of Polytetrafluoroethylene (PTFE)/Al with Si, and CuO, respectively, is higher than that of PTFE/Al. PTFE/Al/Si/CuO reactive materials with four proportions of PTFE/Si were designed by the molding–sintering process to study the influence of different PTFE/Si mass ratios on energy release. A drop hammer was selected for igniting the specimens, and the high-speed camera and spectrometer systems were used to record the energy release process and the flame spectrum, respectively. The ignition height of the reactive material was obtained by fitting the relationship between the flame duration and the drop height. It was found that the ignition height of PTFE/Al/Si/CuO containing 20% PTFE/Si is 48.27 cm, which is the lowest compared to the ignition height of other Si/PTFE ratios of PTFE/Al/Si/CuO; the flame temperature was calculated from the flame spectrum. It was found that flame temperature changes little for the same reactive material at different drop heights. Compared with the flame temperature of PTFE/Al/Si/CuO with four mass ratios, it was found that the flame temperature of PTFE/Al/Si/CuO with 20% PTFE/Si is the highest, which is 2589 K. The results show that PTFE/Al/Si/CuO containing 20% PTFE/Si is easier to be ignited and has a stronger temperature destruction effect.

scholarly journals Variable Temperature Synthesis of Tunable Flame-Generated Carbon Nanoparticles

2021 ◽  
Vol 7 (2) ◽  
pp. 44
Author(s):  
Francesca Picca ◽  
Angela Di Pietro ◽  
Mario Commodo ◽  
Patrizia Minutolo ◽  
Andrea D’Anna
Keyword(s):  
Carbon Nanoparticles ◽  
Variable Temperature ◽  
Flame Temperature ◽  
Cost Effective ◽  
Synthesis Process ◽  
Electrical Mobility ◽  
Material Synthesis ◽  
Online Measurements ◽  
Degree Of Graphitization

In this study, flame-formed carbon nanoparticles of different nanostructures have been produced by changing the flame temperature. Raman spectroscopy has been used for the characterization of the carbon nanoparticles, while the particle size has been obtained by online measurements made by electrical mobility analysis. The results show that, in agreement with recent literature data, a large variety of carbon nanoparticles, with a different degree of graphitization, can be produced by changing the flame temperature. This methodology allows for the synthesis of very small carbon nanoparticles with a size of about 3-4 nm and with different graphitic orders. Under the perspective of the material synthesis process, the variable-temperature flame-synthesis of carbon nanoparticles appears as an attractive procedure for a cost-effective and easily scalable production of highly tunable carbon nanoparticles.

Study on the Effect of Adiabatic Flame Temperature on NOx Formation Using Ethanol Gasoline Blend in SI Engine

2013 ◽  
Vol 781-784 ◽  
pp. 2471-2475 ◽  
Author(s):  
B. M. Masum ◽  
M.A. Kalam ◽  
H.H. Masjuki ◽  
S. M. Palash
Keyword(s):  
Equivalence Ratio ◽  
Gasoline Engine ◽  
Flame Temperature ◽  
Inlet Temperature ◽  
Si Engine ◽  
Nox Formation ◽  
Adiabatic Flame Temperature ◽  
No Formation ◽  
Blended Fuel ◽  
Active Research

Active research and development on using ethanol fuel in gasoline engine had been done for few decades since ethanol served as a potential of infinite fuel supply. This paper discussed analytically and provides data on the effects of compression ratio, equivalence ratio, inlet temperature, inlet pressure and ethanol blend in cylinder adiabatic flame temperature (AFT) and nitrogen oxide (NO) formation of a gasoline engine. Olikara and Borman routines were used to calculate the equilibrium products of combustion for ethanol gasoline blended fuel. The equilibrium values of each species were used to predict AFT and the NO formation of combustion chamber. The result shows that both adiabatic flame temperature and NO formation are lower for ethanol-gasoline blend than gasoline fuel.

Sign in / Sign up

Export Citation Format

Share Document