scholarly journals Influence of gel content on the physical properties of unfilled and carbon black filled natural rubber vulcanizates

2013 ◽  
Vol 32 (6) ◽  
pp. 1135-1144 ◽  
Author(s):  
Adun Nimpaiboon ◽  
Sureerut Amnuaypornsri ◽  
Jitladda Sakdapipanich
Keyword(s):  
Carbon Black ◽  
Natural Rubber ◽  
Physical Properties ◽  
Gel Content ◽  
Natural Rubber Vulcanizates

Effect of Carbon Blacks on Swelling of Neoprene GRM-10 Vulcanizates

1949 ◽  
Vol 22 (3) ◽  
pp. 812-819 ◽  
Author(s):  
N. L. Catton ◽  
D. C. Thompson
Keyword(s):  
Carbon Black ◽  
Natural Rubber ◽  
Physical Properties ◽  
Compression Modulus ◽  
Tension Stress ◽  
Limited Extent ◽  
Carbon Blacks ◽  
Reinforcing Fillers ◽  
Swelling Characteristics ◽  
Natural Rubber Vulcanizates

Abstract Reinforcement of elastomers with fillers has generally been measured by physical properties, such as tension stress-strain, tear resistance, hardness, and compression modulus. To a more limited extent, swelling in solvents has been recognized as associated with reinforcement. In natural-rubber vulcanizates it has been demonstrated that reinforcing fillers impart greater resistance to solvents and oils than do nonreinforcing types. Addition of the latter gives only the reduction in swelling attributable to elastomer dilution. In the case of Neoprene vulcanizates, Catton and Fraser reported that fillers function only as elastomer diluents and that those fillers commonly considered as of the reinforcing type impart no greater resistance to solvents than the nonreinforcing type. More recently, however, Buist and Mottram, in describing the effects of carbon blacks on the physical properties of natural rubber and Neoprene, reported that with both of these elastomers compounds containing thermal type carbon black gave slightly greater swelling in benzene than compounds containing equal loadings of other types of carbon black. With Neoprene, they reported good correlation between moduli and swelling characteristics.

Oxidative Aging of Natural Rubber Vulcanizates. Part III. Crosslink Scission in Monosulfidic Networks

1969 ◽  
Vol 42 (3) ◽  
pp. 924-935 ◽  
Author(s):  
T. Colclough ◽  
J. I. Cunneen ◽  
G. M. C. Hrggins
Keyword(s):  
Natural Rubber ◽  
Physical Properties ◽  
Chemical Structure ◽  
Spectroscopic Methods ◽  
Chemical Probes ◽  
Conjugated Diene ◽  
Strain Measurements ◽  
Oxidative Aging ◽  
Tert Butyl Hydroperoxide ◽  
Natural Rubber Vulcanizates

Abstract A natural rubber vulcanizate containing almost entirely monosulfidic crosslinks was oxidized in oxygen and with tert-butyl hydroperoxide. The changes in physical properties due to oxidation were followed by stress—strain measurements, and the changes in chemical structure were investigated with chemical probes, and by spectroscopic methods. The results show that when the oxidized vulcanizates are heated at 75° C, the monosulfidic crosslinks are broken, that crosslinks containing two sulfur atoms are formed, and that conjugated diene and triene structures are introduced into the main polyisoprene chains.

Structural Characterization of Filled Vulcanizates Part 1. Determination of the Concentration of Chemical Crosslinks in Natural Rubber Vulcanizates Containing High Abrasion Furnace Black

1967 ◽  
Vol 40 (3) ◽  
pp. 866-882 ◽  
Author(s):  
M. Porter
Keyword(s):  
Carbon Black ◽  
Natural Rubber ◽  
Volume Fraction ◽  
Exponential Relationship ◽  
Furnace Black ◽  
Simple Linear Relationship ◽  
Chemical Crosslinks ◽  
Natural Rubber Vulcanizates

Abstract The degree to which HAF black restricts the swelling of natural rubber vulcanizates in n-decane has been determined using a vulcanizing system in which the stoichiometry of crosslinking is unaffected by the carbon black. The dependence of the degree of restriction, as measured by the ratio of the volume fractions of rubber in the filled and unfilled vulcanizates swollen to equilibrium, on the concentration of carbon black follows an exponential relationship previously proposed by Lorenz and Parks. This is found to be equivalent to a simple linear relationship between the apparent and actual crosslink concentrations: napparent/nactual=1+Kϕ, where K is a constant characteristic of the filler and φ is its volume fraction in the vulcanizate. The relation has been used to determine actual crosslink concentrations in filled natural rubber vulcanizates. HAF black is found to cause increases of up to 25 per cent in the yield of polymer to polymer crosslinks in conventional sulfur vulcanizing systems, accompanied by changes in rate of cure and of crosslink reversion. All these are small compared with the effect of the filler on many physical properties.

Prototype of Geocell from Natural Rubber: Effect of Dual-Phase Fillers on Physical Properties of Rubber Compounds Reinforced with Silica and Carbon Black

2017 ◽  
Vol 737 ◽  
pp. 572-577
Author(s):  
Sompatsorn Wongwilatnurak ◽  
Surakit Tuampoemsab ◽  
Rapeephun Dangtungee
Keyword(s):  
Carbon Black ◽  
Natural Rubber ◽  
Physical Properties ◽  
Mechanical Tests ◽  
Silica Content ◽  
Dual Phase ◽  
Chemical Formula ◽  
Tear Strength ◽  
The Road ◽  
Static Mechanical

Geocell, a type of the geosynthetics, is normally used to improve natural geomaterial properties and performance because of confinement and confinement force. This work was an attempt to apply the solid natural rubber (NR) for producing the prototype of geocell with reinforcing the pavement structure of the road. There are three parts of all work in research, which consist of finding the optimal chemical formula, designing and producing the prototype and civil engineering testing of flexible pavement components. This research has emphasized and focused on finding the optimal chemical formula for the prototype production. The effect of silica-carbon black (CB) dual-phase filler on physical properties in terms of only static mechanical tests of the prototype was investigated. The total amount of hybrid reinforcing filler was fixed at 60 phr while the silica/CB ratios were 0/60, 10/50, 20/40, 30/30 and 40/20, respectively. Cure characteristic of the NR compound and physical properties in terms of static mechanical tests such as hardness, tensile and tear strengths of the NR vulcanizates were carried out. The results showed that time to 90% cross-linked (TC 90), hardness and tensile strength of the vulcanized rubber were increased with the increasing of silica content but not for its tear strength. Dispersion of the dual-phase filler in the prototype was reduced when the higher amount of silica in the dual-phase filler was employed as proved by images from the scanning electron microscope. There was only 60 phr CB that was selected as the optimal chemical formula for prototype production as the result of tensile and tear strength.

Effect of Crosslink Density on Cut Growth in Black-Filled Natural Rubber Vulcanizates

2002 ◽  
Vol 75 (5) ◽  
pp. 935-942 ◽  
Author(s):  
G. R. Hamed ◽  
N. Rattanasom
Keyword(s):  
Carbon Black ◽  
Natural Rubber ◽  
Crack Growth ◽  
Crosslink Density ◽  
Longitudinal Crack ◽  
Test Pieces ◽  
Filled Rubber ◽  
Longitudinal Cracks ◽  
Natural Rubber Vulcanizates ◽  
High Crosslink Density

Abstract Tensile strengths, σb, of gum and N115-filled natural rubber test pieces, with and without edge pre-cuts, have been determined. At low crosslink density, the regular (uncut) σb of filled and gum vulcanizates is similar. However, at high crosslink density, the gum NR becomes brittle, while the corresponding filled rubber remains strong and resistant to cut growth. It is proposed that the tightly linked gum does not strain-crystallize appreciably during stretching, but that its filled counterpart does. Carbon black appears capable of inducing crystallization in a network that alone remains amorphous during extension. Filled vulcanizates of various crosslink densities have similar normal tensile strengths ( ≈ 30 MPa), but strengths differ, sometimes more than twofold, if a pre-cut is present. Lightly crosslinked specimens containing a small cut have strengths that depend very weakly on cut size, c. Furthermore, these develop long longitudinal cracks from which catastrophic rupture initiates. With larger cuts, strength decreases more rapidly with increasing c, there is less longitudinal crack growth, and rupture initiates near the original cut tip. In contrast, the strength of a highly crosslinked vulcanizate is sensitive to small cuts and test pieces exhibit minimal longitudinal cracking before failure.

Aromatic and Epoxidised Oil Curing and Rebound Resilience Characteristic and their Humidity Effect of Hardness on NR Vulcanizates

2013 ◽  
Vol 812 ◽  
pp. 138-144 ◽  
Author(s):  
Mohamed Rahmah ◽  
Wan Zain Norazira ◽  
Shafie Nur Ashyikin ◽  
Mohd Nurazzi Norizan
Keyword(s):  
Natural Rubber ◽  
Physical Properties ◽  
Room Temperature ◽  
Rubber Compound ◽  
Humidity Effect ◽  
Humidity Level ◽  
Cure Time ◽  
Humidity Chamber ◽  
Overall Performance ◽  
Natural Rubber Vulcanizates

Recently, aromatic oil (AO) is one of the substances that is typically used as a processing aid especially for high filler loadings in formulating rubber compound. Aromatic oil has disadvantages in that, it is hazardous to environment, toxic and has been labeled as carcinogenic. In this research, an epoxidised oil (EO) and aromatic oil were used to investigate the effect incorporation of oil onto the SBR/NR natural rubber vulcanizates (NR). From the result obtained, EO showed shorter cure time and scorch time as the oil loading were increased up to 20 pphr of EO. Physical properties such as hardness and rebound resilience of NR/EO vulcanisate were also investigated upon exposure to different humidity level in humidity chamber. At room temperature, the hardness of EO loading onto the SBR/NR vulcanisate is lower than AO loadings. Hardness was slightly decreased with increasing rate of humidity. There is great difference in hardness and rebound resilience values between AO and EO. Both hardness and rebound resilience were not affected by humidity. This implies the existence of good filler interaction with EO and rubber which do not impart changes in the hardness and resilience properties of rubber compound. Epoxidised oil has great promising potential to replace the carcinogenic aromatic oil as it has good overall performance and renewable in nature .

Effect of Vulcanization Additive on Cure Characteristics and Physical Properties of Silica Filled Epoxidised Natural Rubber Truck Tyre Tread Compound

2015 ◽  
Vol 1107 ◽  
pp. 113-118
Author(s):  
Ahmad Kifli Che Aziz ◽  
Teku Zakwan Zaeimoedin ◽  
Mazlina Mustafa Kamal
Keyword(s):  
Carbon Black ◽  
Natural Rubber ◽  
Physical Properties ◽  
Abrasion Resistance ◽  
Butadiene Rubber ◽  
Cure Characteristics ◽  
Truck Tyre ◽  
Curing Systems

The challenges of using Epoxidised Natural Rubber (ENR) in truck tyre tread are to achieve good cure reversion resistant and physical properties especially on abrasion resistance towards long vulcanization time. The objectives of the project are to study the effects of vulcanization additive on cure characteristics and physical properties of silica filled ENR compound. In this work, a variation of curing systems were employed and a standard carbon black filled Natural Rubber/Butadiene Rubber (NR/BR) compound as a comparison. Greater reversion resistance and physical properties were observed with inclusion of vulcanization additive in the silica compound as compared to compound containing any. The abrasion resistance on the hand improved in spite of long vulcanisation time which commonly practices in truck tyre manufacturing.Keywords: ENR, silica, vulcanization additive, cure reversion, abrasion resistance

Modeling of Carbon Black Filled Natural Rubber Vulcanizates by the Standard Triboelastic Solid

1999 ◽  
Vol 72 (4) ◽  
pp. 673-683 ◽  
Author(s):  
V. A. Coveney ◽  
D. E. Johnson
Keyword(s):  
Mathematical Modeling ◽  
Carbon Black ◽  
Natural Rubber ◽  
Dynamic Behavior ◽  
Low Frequency ◽  
Specific Reference ◽  
Published Data ◽  
General Terms ◽  
Wide Range ◽  
Natural Rubber Vulcanizates

Abstract Mathematical modeling of the dynamic behavior of vulcanizates is reviewed with the emphasis on carbon black filled natural rubber (NR). The 3 constant standard triboelastic solid (STS) model and its behavior are described, in general terms and with specific reference to low frequency shear data for a wide range of filled NR vulcanizates. Good general agreement is found between model and experiment for the data obtained at strain amplitudes down to 0.01; there is also acceptably good correlation between carbon black loading and values of STS constants. For previously published data down to very low strain amplitudes (1×10−4), agreement is much less satisfactory.

Sign in / Sign up

Export Citation Format

Share Document