Heat propagation of circular thin-walled parts fabricated in additive manufacturing using gas metal arc welding

2018 ◽  
Vol 251 ◽  
pp. 12-19 ◽  
Author(s):  
Jun Xiong ◽  
Rong Li ◽  
Yangyang Lei ◽  
Hui Chen
Keyword(s):  
Additive Manufacturing ◽  
Arc Welding ◽  
Gas Metal Arc Welding ◽  
Heat Propagation ◽  
Metal Arc Welding ◽  
Thin Walled

scholarly journals A preliminary study on gas metal arc welding-based additive manufacturing of metal parts

2020 ◽  
Vol 23 (1) ◽  
Author(s):  
Van Thao LE
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
Mild Steel ◽  
Arc Welding ◽  
Gas Metal Arc Welding ◽  
Internal Quality ◽  
Test Machine ◽  
Welding Robot ◽  
Metal Arc Welding ◽  
Thin Walled

Introduction: In the past three decades, additive manufacturing (AM), also known as 3D printing, has emerged as a promising technology, which allows the manufacture of complex parts by adding material layer upon layer. In comparison, with other metal-based AM technologies, gas metal arc welding-based additive manufacturing (GMAW-based AM) presents a high deposition rate and has the potential for producing medium and large metal components. To validate the technological performance of such a manufacturing process, the internal quality of manufactured parts needs to be analyzed, particularly in the cases of manufacturing the parts working in a critical load-bearing condition. Therefore, this paper aims at investigating the internal quality (i.e., and mechanical properties) of components manufactured by the GMAW-based AM technology. Method: A gas metal arc welding robot was used to build a thin-walled component made of mild steel on a low-carbon substrate according to the AM principle. Thereafter, the specimens for observing and mechanical properties were extracted from the built thin-walled component. The of the specimen were observed by an optical microscope; the hardness was measured by a digital tester, and the tensile tests were carried out on a tensile test machine. Results: The results show that the GMAW-based AM-built thin-walled components possess an adequate that varies from the top to the bottom of the built component: structures with primary dendrites in the upper zone; granular structure of with small regions of at grain boundaries in the middle zone, and grains of in the lower zone. The hardness (ranged between 164±3.46 HV to 192±3.81 HV), yield strength (YS offset of 0.2% ranged from 340±2 to 349.67±1.53 ), and ultimate tensile strength (UTS ranged from 429±1 to 477±2 ) of the GMAW-based AM-built components were comparable to those of wrought mild steel. Conclusions: The results obtained in this study demonstrate that the GMAW-based AM-built components possess adequate and good mechanical properties for real applications. This allows us to confirm the feasibility of using a conventional gas metal arc welding robot for additive manufacturing or repairing/re-manufacturing of metal components.

scholarly journals Wire Arc Additive Manufacturing (WAAM) of Aluminum Alloy AlMg5Mn with Energy-Reduced Gas Metal Arc Welding (GMAW)

Materials ◽  
2020 ◽  
Vol 13 (12) ◽  
pp. 2671 ◽  
Author(s):  
Maximilian Gierth ◽  
Philipp Henckell ◽  
Yarop Ali ◽  
Jonas Scholl ◽  
Jean Pierre Bergmann
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
Arc Welding ◽  
Energy Input ◽  
Large Scale ◽  
Unit Length ◽  
Gas Metal Arc Welding ◽  
Cold Metal Transfer ◽  
Metal Arc Welding ◽  
Wire Arc Additive Manufacturing

Large-scale aluminum parts are used in aerospace and automotive industries, due to excellent strength, light weight, and the good corrosion resistance of the material. Additive manufacturing processes enable both cost and time savings in the context of component manufacturing. Thereby, wire arc additive manufacturing (WAAM) is particularly suitable for the production of large volume parts due to deposition rates in the range of kilograms per hour. Challenges during the manufacturing process of aluminum alloys, such as porosity or poor mechanical properties, can be overcome by using arc technologies with adaptable energy input. In this study, WAAM of AlMg5Mn alloy was systematically investigated by using the gas metal arc welding (GMAW) process. Herein, correlations between the energy input and the resulting temperature–time-regimes show the effect on resulting microstructure, weld seam irregularities and the mechanical properties of additively manufactured aluminum parts. Therefore, multilayer walls were built layer wise using the cold metal transfer (CMT) process including conventional CMT, CMT advanced and CMT pulse advanced arc modes. These processing strategies were analyzed by means of energy input, whereby the geometrical features of the layers could be controlled as well as the porosity to area portion to below 1% in the WAAM parts. Furthermore, the investigations show the that mechanical properties like tensile strength and material hardness can be adapted throughout the energy input per unit length significantly.

scholarly journals Gas Metal Arc Welding Modes in Wire Arc Additive Manufacturing of Ti-6Al-4V

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2457
Author(s):  
Oleg Panchenko ◽  
Dmitry Kurushkin ◽  
Fedor Isupov ◽  
Anton Naumov ◽  
Ivan Kladov ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Arc Welding ◽  
High Speed ◽  
Gas Metal Arc Welding ◽  
Metal Transfer ◽  
Process Data ◽  
Cold Metal Transfer ◽  
Wall Width ◽  
Metal Arc Welding ◽  
Wire Arc Additive Manufacturing

In wire arc additive manufacturing of Ti-alloy parts (Ti-WAAM) gas metal arc welding (GMAW) can be applied for complex parts printing. However, due to the specific properties of Ti, GMAW of Ti-alloys is complicated. In this work, three different types of metal transfer modes during Ti-WAAM were investigated: Cold Metal Transfer, controlled short circuiting metal transfer, and self-regulated metal transfer at a direct current with a negative electrode. Metal transfer modes were studied using captured waveform and high-speed video analysis. Using these modes, three walls were manufactured; the geometry preservation stability was estimated and compared using effective wall width calculation, the microstructure was analyzed using optical microscopy. Transfer process data showed that arc wandering depends not only on cathode spot instabilities, but also on anode processing properties. Microstructure analysis showed that each produced wall consists of phases and structures inherent for Ti-WAAM. α-basketweave in the center of and α-colony on the grain boundary of epitaxially grown β-grains were found with heat affected zone bands along the height of the walls, so that the microstructure did not depend on metal transfer dramatically. However, the geometry preservation stability was higher in the wall, produced with controlled short circuiting metal transfer.

scholarly journals Reduction of Energy Input in Wire Arc Additive Manufacturing (WAAM) with Gas Metal Arc Welding (GMAW)

Materials ◽  
2020 ◽  
Vol 13 (11) ◽  
pp. 2491 ◽  
Author(s):  
Philipp Henckell ◽  
Maximilian Gierth ◽  
Yarop Ali ◽  
Jan Reimann ◽  
Jean Pierre Bergmann
Keyword(s):  
Additive Manufacturing ◽  
Arc Welding ◽  
Energy Input ◽  
Gas Metal Arc Welding ◽  
Welding Process ◽  
Energy Reduction ◽  
Main Challenge ◽  
Metal Arc Welding ◽  
Welding Processes ◽  
Wire Arc Additive Manufacturing

Wire arc additive manufacturing (WAAM) by gas metal arc welding (GMAW) is a suitable option for the production of large volume metal parts. The main challenge is the high and periodic heat input of the arc on the generated layers, which directly affects geometrical features of the layers such as height and width as well as metallurgical properties such as grain size, solidification or material hardness. Therefore, processing with reduced energy input is necessary. This can be implemented with short arc welding regimes and respectively energy reduced welding processes. A highly efficient strategy for further energy reduction is the adjustment of contact tube to work piece distance (CTWD) during the welding process. Based on the current controlled GMAW process an increase of CTWD leads to a reduction of the welding current due to increased resistivity in the extended electrode and constant voltage of the power source. This study shows the results of systematically adjusted CTWD during WAAM of low-alloyed steel. Thereby, an energy reduction of up to 40% could be implemented leading to an adaptation of geometrical and microstructural features of additively manufactured work pieces.

scholarly journals Model for the Prediction of Deformations in the Manufacture of Thin-Walled Parts by Wire Arc Additive Manufacturing Technology

Metals ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 678
Author(s):  
Mikel Casuso ◽  
Fernando Veiga ◽  
Alfredo Suárez ◽  
Trunal Bhujangrao ◽  
Eider Aldalur ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Gas Metal Arc Welding ◽  
Element Model ◽  
Manufacturing Technology ◽  
Final Part ◽  
Metal Arc Welding ◽  
Thin Walled ◽  
Industrial Level ◽  
Manufacturing Alternatives ◽  
Wire Arc Additive Manufacturing

Gas Metal Arc Welding (GMAW) is a manufacturing technology included within the different Wire Arc Additive Manufacturing alternatives. These technologies have been generating great attention among scientists in recent decades. Its main qualities that make it highly productive with a large use of material with relatively inexpensive machine solutions make it a very advantageous technology. This paper covers the application of this technology for the manufacture of thin-walled parts. A finite element model is presented for estimating the deformations in this type of parts. This paper presents a simulation model that predicts temperatures with less than 5% error and deformations of the final part that, although quantitatively has errors of 20%, qualitatively allows to know the deformation modes of the part. Knowing the part areas subject to greater deformation may allow the future adaptation of deposition strategies or redesigns for their adaptation. These models are very useful both at a scientific and industrial level since when we find ourselves with a technology oriented to Near Net Shape (NNS) manufacturing where deformations are critical for obtaining the final part in a quality regime.

Sign in / Sign up

Export Citation Format

Share Document