Research of the recast layer on implant surface modified by micro-current electrical discharge machining using deionized water mixed with titanium powder as dielectric solvent

2014 ◽  
Vol 311 ◽  
pp. 47-53 ◽  
Author(s):  
Sung-Long Chen ◽  
Ming-Hong Lin ◽  
Guo-Xin Huang ◽  
Chia-Ching Wang
Keyword(s):  
Electrical Discharge ◽  
Titanium Powder ◽  
Electrical Discharge Machining ◽  
Recast Layer ◽  
Deionized Water ◽  
Implant Surface ◽  
Surface Modified

scholarly journals The Effect of Discharge Current and Pulse-On Time on Biocompatible Zr-based BMG Sinking-EDM

2020 ◽  
Vol 10 (1) ◽  
pp. 401-407
Author(s):  
Yanuar Rohmat Aji Pradana ◽  
Aldi Ferara ◽  
Aminnudin Aminnudin ◽  
Wahono Wahono ◽  
Jason Shian-Ching Jang
Keyword(s):  
Surface Roughness ◽  
Metallic Glasses ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Surface Hardness ◽  
Recast Layer ◽  
Surface Evaporation ◽  
Pulse On Time

AbstractThe machinability information of Zr-based bulk metallic glasses (BMGs) are recently limited but essential to provide technological recommendation for the fabrication of the medical devices due to the material’s metastable nature. This study aims to investigate the material removal rate (MRR) and surface roughness under different current and pulse-on time of newly developed Ni- and Cu-free Zr-based BMG using sinking-electrical discharge machining (EDM). By using weightloss calculation, surface roughness test and scanning electron microscopy (SEM) observation on the workpiece after machining, both MRR and surface roughness were obtained to be increased up to 0.594 mm3/min and 5.50 μm, respectively, when the higher current was applied. On the other hand, the longer pulse-on time shifted the Ra into the higher value but lower the MRR value to only 0.183 mm3/min at 150 μs. Contrary, the surface hardness value was enhanced by both higher current and pulse-on time applied during machining indicating different level of structural change after high-temperature spark exposure on the BMG surface. These phenomena are strongly related to the surface evaporation which characterize the formation of crater and recast layer in various thicknesses and morphologies as well as the crystallization under the different discharge energy and exposure time.

Machining Feasibility of a New Developed Medium in Electrical Discharge Machining

2015 ◽  
Vol 656-657 ◽  
pp. 335-340 ◽  
Author(s):  
Fang Pin Chuang ◽  
Yan Cherng Lin ◽  
Hsin Min Lee ◽  
Han Ming Chow ◽  
A. Cheng Wang
Keyword(s):  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Environmentally Friendly ◽  
Industrial Applications ◽  
Deionized Water ◽  
Machining Parameters ◽  
Machining Performance ◽  
Machining Characteristics

The environment issue and green machining technique have been induced intensive attention in recent years. It is urgently need to develop a new kind dielectric to meet the requirements for industrial applications. The aim of this study is to develop a novel dielectric using gas media immersed in deionized water for electrical discharge machining (EDM). The developed machining medium for EDM can fulfill the environmentally friendly issue and satisfy the demand of high machining performance. The experiments were conducted by this developed medium to investigate the effects of machining parameters on machining characteristics in terms of material removal rate (MRR) and surface roughness. The developed EDM medium revealed the potential to obtain a stabilizing progress with excellent machining performance and environmentally friendly feature.

scholarly journals Experimental Research on Discharge Forming Cutting-Electrochemical Machining of Single-Crystal Silicon

2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Bin Xin ◽  
Wei Liu
Keyword(s):  
Surface Roughness ◽  
Single Crystal ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Electrochemical Machining ◽  
Single Crystal Silicon ◽  
Recast Layer ◽  
Movement Speed ◽  
Crystal Silicon ◽  
Wedm Process

During the wire electrical discharge machining (WEDM) process, a large number of discharge pits and a recast layer are easily generated on the workpiece surface, resulting in high surface roughness. A discharge forming cutting-electrochemical machining method for fabricating single-crystal silicon is proposed in this study to solve this problem. On the same processing equipment, single-crystal silicon is first cut using the discharge forming cutting method. Second, electrochemical anodic reaction technology is used to dissolve the discharge pits and recast layer on the single-crystal silicon surface. The machining mechanism of this process, the surface elements of the processed single-crystal silicon and a comparison of the kerf width are analyzed through experiments. On this basis, the influence of the movement speed of the copper foil electrode during electrochemical anodic dissolution on the final surface roughness is qualitatively analyzed. The experimental results show that discharge forming cutting-electrochemical machining can effectively eliminate the electrical discharge pits and recast layer, which are caused by electric discharge cutting, on the surface of single-crystal silicon, thereby reducing the surface roughness of the workpiece.

scholarly journals Processing Characteristics of Micro Electrical Discharge Machining for Surface Modification of TiNi Shape Memory Alloys Using a TiC Powder Dielectric

Micromachines ◽  
2020 ◽  
Vol 11 (11) ◽  
pp. 1018
Author(s):  
Ziliang Zhu ◽  
Dengji Guo ◽  
Jiao Xu ◽  
Jianjun Lin ◽  
Jianguo Lei ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Surface Modification ◽  
Shape Memory ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Recast Layer ◽  
Powder Concentration ◽  
Micro Electrical Discharge Machining ◽  
Machining Properties

Titanium-nickel shape memory alloy (SMA) has good biomedical application value as an implant. Alloy corrosion will promote the release of toxic nickel ions and cause allergies and poisoning of cells and tissues. With this background, surface modification of TiNi SMAs using TiC-powder-assisted micro-electrical discharge machining (EDM) was proposed. This aims to explore the effect of the electrical discharge machining (EDM) parameters and TiC powder concentration on the machining properties and surface characteristics of the TiNi SMA. It was found that the material removal rate (MRR), surface roughness, and thickness of the recast layer increased with an increase in the discharge energy. TiC powder’s addition had a positive effect on increasing the electro-discharge frequency and MRR, reducing the surface roughness, and the maximum MRR and the minimum surface roughness occurred at a mixed powder concentration of 5 g/L. Moreover, the recast layer had good adhesion and high hardness due to metallurgical bonding. XRD analysis found that the machined surface contains CuO2, TiO2, and TiC phases, contributing to an increase in the surface microhardness from 258.5 to 438.7 HV, which could be beneficial for wear resistance in biomedical orthodontic applications.

Surfactant and graphite powder–assisted electrical discharge machining of titanium alloy

2016 ◽  
Vol 231 (4) ◽  
pp. 641-657 ◽  
Author(s):  
Murahari Kolli ◽  
Adepu Kumar
Keyword(s):  
Surface Roughness ◽  
Titanium Alloy ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Graphite Powder ◽  
Recast Layer ◽  
Dielectric Fluid ◽  
Recast Layer Thickness

Surfactant and graphite powder–assisted electrical discharge machining was proposed and experiments were performed on titanium alloy in this investigation. Analysis was carried out to observe changes in dielectric fluid behaviour, material removal rate, surface roughness, recast layer thickness, surface topography and energy-dispersive X-ray spectroscopy. It was found out that the addition of surfactant to dielectric fluid (electrical discharge machining oil + graphite powder) improved the material removal rate and surface roughness. It was noticed to have reduced the recast layer thickness and agglomeration of graphite and sediment particles. Biface material migrations between the electrode and the workpiece surface were identified, and migration behaviour was powerfully inhibited by the mixing of surfactant. Surfactant added into dielectric fluid played an important role in the discharge gap, which increased the conductivity, and suspended debris particles in dielectric fluid reduced the abnormal discharge conditions of the machine and improved the overall machining efficiency.

Modeling of Recast Layer in Micro-Electrical Discharge Machining

2010 ◽  
Vol 132 (3) ◽  
Author(s):  
P. C. Tan ◽  
S. H. Yeo
Keyword(s):  
Numerical Model ◽  
Electrical Discharge ◽  
Prediction Models ◽  
Electrical Discharge Machining ◽  
Performance Measure ◽  
Recast Layer ◽  
Micro Edm ◽  
Machined Surface ◽  
Functional Layer ◽  
Pulse On Time

The thickness of recast layers produced during electrical discharge machining (EDM) is an important process performance measure as it may indicate an extent of crack propagation in a machined surface or thickness of a functional layer alloyed onto a machined surface. Thus, the availability of the recast layer thickness prediction models is needed to allow better control of machining outcomes, which becomes more vital for micro-EDM due to the microscale of machined features. The proposed numerical model, based on a multiple discharge approach for recast layer prediction, is developed to fill an existing gap in micro-EDM. The multiple discharge approach accounts for the overlapping nature by which craters are generated on the machined surface and considers the recast layer to be a combination of individual recast regions from individual craters. The numerical analysis, based on finite element methods, is used to determine the melting isotherms due to heat inputs on overlapping crater profiles. Then, a hemispherical-capped crater profile is estimated by applying a recast plasma flushing efficiency to the amount of molten material bounded by the melting isotherm. Finally, the recast region is defined to be bounded by the melting isotherm and crater profile. The model, developed for a peak discharge current of 1.45 A and pulse on time between 166 ns and 606 ns, predicted recast layer thicknesses of between 1.0 μm and 1.82 μm. It is then validated at pulse on time settings of 244 ns and 458 ns, which generated average recast layer thicknesses of 1.18 μm and 1.56 μm, respectively. Thus, the numerical model developed using the multiple discharge approach is suitable for estimation of recast layer thicknesses in micro-EDM.

Crack-Less Electrical Discharge Machining of Molybdenum with Titanium Electrode

2014 ◽  
Vol 510 ◽  
pp. 101-105 ◽  
Author(s):  
Kaneko Kensei ◽  
Furutani Katsushi
Keyword(s):  
High Temperature ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Base Material ◽  
Negative Electrode ◽  
High Hardness ◽  
Recast Layer ◽  
Recrystallization Temperature ◽  
High Temperature Strength ◽  
Electrode Polarity

This paper describescrack-less electrical discharge machining (EDM) of molybdenum (Mo) with titanium (Ti) electrode. Mo is often machined by EDM because of its high hardness. However, a molybdenum carbide (MoC and Mo2C) layer with high hardness and brittleness is formed by EDM in kerosene oil. Moreover, Mo becomes recrystallizationembrittlement at high temperature. Therefore, many cracks occurred in the EDMed surface. On the other hand, the addition of Ti rises recrystallization temperature and improves high temperature strength of Mo.In order to decrease the cracks in the machined surface, Mo was machined by EDM with a Ti electrode in deionized water. In the case of the positive electrode polarity, many cracks occurred in the base material and recast layer. The cracks in the base material might generate by crystal grain boundary embrittlement. In contrast, the EDMed surface indicated crack-less on the negative electrode polarity. To clarify the causes of crack-less surface on negative electrode polarity, componential analysis of EDMed surface was carried out. The component ratio of Ti on the negative electrode polarity was higher than that on the positive. In addition, the recast layer was composed by Mo-Ti solid solution.

Sign in / Sign up

Export Citation Format

Share Document