Microstructures and mechanical properties of metastable Ti–30Zr–(Cr, Mo) alloys with changeable Young’s modulus for spinal fixation applications

2011 ◽  
Vol 7 (8) ◽  
pp. 3230-3236 ◽  
Author(s):  
Xiaoli Zhao ◽  
Mitsuo Niinomi ◽  
Masaaki Nakai ◽  
Goro Miyamoto ◽  
Tadashi Furuhara
Keyword(s):  
Mechanical Properties ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Spinal Fixation ◽  
Microstructures And Mechanical Properties

Development of Changeable Young's Modulus with Good Mechanical Properties in β-Type Ti-Cr-O Alloys

2013 ◽  
Vol 575-576 ◽  
pp. 453-460
Author(s):  
Hui Hong Liu ◽  
Mitsuo Niinomi ◽  
Masaaki Nakai ◽  
Junko Hieda ◽  
Ken Cho
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Stress Shielding ◽  
Shielding Effect ◽  
Potential Candidate ◽  
Spinal Fixation ◽  
High Tensile Strength ◽  
Cold Rolled

A novel β-type titanium alloy with a changeable Youngs modulus, that is, with a low Young's modulus to prevent the stress-shielding effect for patients and a high Young's modulus to suppress springback for surgeons, should be developed in order to satisfy the conflicting requirements of both the patients and surgeons in spinal fixation operations. In this study, the oxygen content in ternary Ti-11Cr-O alloys was optimized in order to achieve a large changeable Young's modulus with good mechanical properties for spinal fixation applications. The increase in Youngs moduli of all the examined alloys by cold rolling is attributed to the deformation-induced ω-phase transformation which is suppressed by oxygen. Among the examined alloys, the Ti-11Cr-0.2O alloy exhibits the largest changeable Youngs modulus and a high tensile strength with an acceptable plasticity under both solution-treated (ST) and cold-rolled (CR) conditions. Therefore, the Ti-11Cr-0.2O alloy, which shows a good balance among a changeable Youngs modulus, high tensile strength and good plasticity, is considered a potential candidate for spinal fixation applications.

Mechanical properties of FeAlSi powders prepared by mechanical alloying from different initial feedstock materials

2019 ◽  
Vol 107 (2) ◽  
pp. 207 ◽  
Author(s):  
Jaroslav Čech ◽  
Petr Haušild ◽  
Miroslav Karlík ◽  
Veronika Kadlecová ◽  
Jiří Čapek ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Mechanical Alloying ◽  
Young’S Modulus ◽  
Milling Time ◽  
Young's Modulus ◽  
Element Model ◽  
X Ray Diffraction ◽  
X Ray ◽  
Powder Particles ◽  
Complete Homogenization

FeAl20Si20 (wt.%) powders prepared by mechanical alloying from different initial feedstock materials (Fe, Al, Si, FeAl27) were investigated in this study. Scanning electron microscopy, X-ray diffraction and nanoindentation techniques were used to analyze microstructure, phase composition and mechanical properties (hardness and Young’s modulus). Finite element model was developed to account for the decrease in measured values of mechanical properties of powder particles with increasing penetration depth caused by surrounding soft resin used for embedding powder particles. Progressive homogenization of the powders’ microstructure and an increase of hardness and Young’s modulus with milling time were observed and the time for complete homogenization was estimated.

scholarly journals First principles computation of composition dependent elastic constants of omega in titanium alloys: implications on mechanical behavior

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
R. Salloom ◽  
S. A. Mantri ◽  
R. Banerjee ◽  
S. G. Srinivasan
Keyword(s):  
Mechanical Properties ◽  
Young’S Modulus ◽  
First Principles ◽  
Young's Modulus ◽  
Group Vi ◽  
Group V ◽  
Β Phase ◽  
Ti Alloys ◽  
Ω Phase ◽  
Stabilizer Concentration

AbstractFor decades the poor mechanical properties of Ti alloys were attributed to the intrinsic brittleness of the hexagonal ω-phase that has fewer than 5-independent slip systems. We contradict this conventional wisdom by coupling first-principles and cluster expansion calculations with experiments. We show that the elastic properties of the ω-phase can be systematically varied as a function of its composition to enhance both the ductility and strength of the Ti-alloy. Studies with five prototypical β-stabilizer solutes (Nb, Ta, V, Mo, and W) show that increasing β-stabilizer concentration destabilizes the ω-phase, in agreement with experiments. The Young’s modulus of ω-phase also decreased at larger concentration of β-stabilizers. Within the region of ω-phase stability, addition of Nb, Ta, and V (Group-V elements) decreased Young’s modulus more steeply compared to Mo and W (Group-VI elements) additions. The higher values of Young’s modulus of Ti–W and Ti–Mo binaries is related to the stronger stabilization of ω-phase due to the higher number of valence electrons. Density of states (DOS) calculations also revealed a stronger covalent bonding in the ω-phase compared to a metallic bonding in β-phase, and indicate that alloying is a promising route to enhance the ω-phase’s ductility. Overall, the mechanical properties of ω-phase predicted by our calculations agree well with the available experiments. Importantly, our study reveals that ω precipitates are not intrinsically embrittling and detrimental, and that we can create Ti-alloys with both good ductility and strength by tailoring ω precipitates' composition instead of completely eliminating them.

scholarly journals Tailoring a Low Young Modulus for a Beta Titanium Alloy by Combining Severe Plastic Deformation with Solution Treatment

Materials ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3467
Author(s):  
Anna Nocivin ◽  
Doina Raducanu ◽  
Bogdan Vasile ◽  
Corneliu Trisca-Rusu ◽  
Elisabeta Mirela Cojocaru ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Plastic Deformation ◽  
Severe Plastic Deformation ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Solution Treatment ◽  
Young Modulus ◽  
Orthopedic Implants ◽  
Beta Titanium Alloy

The present paper analyzed the microstructural characteristics and the mechanical properties of a Ti–Nb–Zr–Fe–O alloy of β-Ti type obtained by combining severe plastic deformation (SPD), for which the total reduction was of etot = 90%, with two variants of super-transus solution treatment (ST). The objective was to obtain a low Young’s modulus with sufficient high strength in purpose to use the alloy as a biomaterial for orthopedic implants. The microstructure analysis was conducted through X-ray diffraction (XRD), scanning electron microscopy (SEM), and high-resolution transmission electron microscopy (HRTEM) investigations. The analyzed mechanical properties reveal promising values for yield strength (YS) and ultimate tensile strength (UTS) of about 770 and 1100 MPa, respectively, with a low value of Young’s modulus of about 48–49 GPa. The conclusion is that satisfactory mechanical properties for this type of alloy can be obtained if considering a proper combination of SPD + ST parameters and a suitable content of β-stabilizing alloying elements, especially the Zr/Nb ratio.

scholarly journals Phase Formation, Microstructure and Mechanical Properties of Mg67Ag33 as Potential Biomaterial

Metals ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 461
Author(s):  
Konrad Kosiba ◽  
Konda Gokuldoss Prashanth ◽  
Sergio Scudino
Keyword(s):  
Mechanical Properties ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Equilibrium Phase ◽  
Antibacterial Properties ◽  
Equilibrium Phase Diagram ◽  
Compressive Yield Strength ◽  
X Ray ◽  
Fine Grained ◽  
Equilibrium Phases

The phase and microstructure formation as well as mechanical properties of the rapidly solidified Mg67Ag33 (at. %) alloy were investigated. Owing to kinetic constraints effective during rapid cooling, the formation of equilibrium phases is suppressed. Instead, the microstructure is mainly composed of oversaturated hexagonal closest packed Mg-based dendrites surrounded by a mixture of phases, as probed by X-ray diffraction, electron microscopy and energy dispersive X-ray spectroscopy. A possible non-equilibrium phase diagram is suggested. Mainly because of the fine-grained dendritic and interdendritic microstructure, the material shows appreciable mechanical properties, such as a compressive yield strength and Young’s modulus of 245 ± 5 MPa and 63 ± 2 GPa, respectively. Due to this low Young’s modulus, the Mg67Ag33 alloy has potential for usage as biomaterial and challenges ahead, such as biomechanical compatibility, biodegradability and antibacterial properties are outlined.

scholarly journals Effect of Nanopores on Mechanical Properties of the Shape Memory Alloy

Micromachines ◽  
2021 ◽  
Vol 12 (5) ◽  
pp. 529
Author(s):  
Chunzhi Du ◽  
Zhifan Li ◽  
Bingfei Liu
Keyword(s):  
Mechanical Properties ◽  
Constitutive Model ◽  
Shape Memory ◽  
Young’S Modulus ◽  
Residual Strain ◽  
Surface Effect ◽  
Young's Modulus ◽  
Strain Curve ◽  
Stress Strain ◽  
Strength Limit

Nanoporous Shape Memory Alloys (SMA) are widely used in aerospace, military industry, medical and health and other fields. More and more attention has been paid to its mechanical properties. In particular, when the size of the pores is reduced to the nanometer level, the effect of the surface effect of the nanoporous material on the mechanical properties of the SMA will increase sharply, and the residual strain of the SMA material will change with the nanoporosity. In this work, the expression of Young’s modulus of nanopore SMA considering surface effects is first derived, which is a function of nanoporosity and nanopore size. Based on the obtained Young’s modulus, a constitutive model of nanoporous SMA considering residual strain is established. Then, the stress–strain curve of dense SMA based on the new constitutive model is drawn by numerical method. The results are in good agreement with the simulation results in the published literature. Finally, the stress-strain curves of SMA with different nanoporosities are drawn, and it is concluded that the Young’s modulus and strength limit decrease with the increase of nanoporosity.

Sign in / Sign up

Export Citation Format

Share Document