Influence of the wall boundary layer thickness on a gas jet injected into a liquid crossflow

2001 ◽  
Vol 30 (4) ◽  
pp. 458-466 ◽  
Author(s):  
O. Vigneau ◽  
S. Pignoux ◽  
J. L. Carreau ◽  
F. Roger
Keyword(s):  
Boundary Layer ◽  
Layer Thickness ◽  
Boundary Layer Thickness ◽  
Gas Jet ◽  
Wall Boundary Layer ◽  
Wall Boundary

A Review of Cascade Data on Secondary Losses in Turbines

1970 ◽  
Vol 12 (1) ◽  
pp. 48-59 ◽  
Author(s):  
J. Dunham
Keyword(s):  
Boundary Layer ◽  
Layer Thickness ◽  
Boundary Layers ◽  
Boundary Layer Thickness ◽  
Blade Loading ◽  
Axial Turbine ◽  
Wall Boundary Layer ◽  
Wall Boundary ◽  
Turbine Cascades

Theories and experiments on secondary losses in axial turbine cascades without end clearance are reviewed. A formula is given which correlates the effect of blade loading on secondary losses more successfully than hitherto. However, it is also shown that secondary losses increase with upstream wall boundary layer thickness. Only a tentative expression for that effect can be suggested. In order to predict secondary losses reliably more must be known about these wall boundary layers.

Characteristics of the Flow Past a Wall-Mounted Finite-Length Square Cylinder at Low Reynolds Number With Varying Boundary Layer Thickness

2019 ◽  
Vol 141 (6) ◽  
Author(s):  
Sachidananda Behera ◽  
Arun K. Saha
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Flow Field ◽  
Layer Thickness ◽  
Finite Length ◽  
Boundary Layer Thickness ◽  
Square Cylinder ◽  
Near Wake ◽  
Wall Boundary Layer ◽  
Wall Boundary

Direct numerical simulation (DNS) is performed to investigate the modes of shedding of the wake of a wall-mounted finite-length square cylinder with an aspect ratio (AR) of 7 for six different boundary layer thicknesses (0.0–0.30) at a Reynolds number of 250. For all the cases of wall boundary layer considered in this study, two modes of shedding, namely, anti-symmetric and symmetric modes of shedding, were found to coexist in the cylinder wake with symmetric one occurring intermittently for smaller time duration. The phase-averaged flow field revealed that the symmetric modes of shedding occur only during instances when the near wake experiences the maximum strength of upwash/downwash flow. The boundary layer thickness seems to have a significant effect on the area of dominance of both downwash and upwash flow in instantaneous and time-averaged flow field. It is observed that the near-wake topology and the total drag force acting on the cylinder are significantly affected by the bottom-wall boundary layer thickness. The overall drag coefficient is found to decrease with thickening of the wall boundary layer thickness.

Modeling the 3-D Flow Effects on Deviation Angle for Axial Compressor Middle Stages

1986 ◽  
Vol 108 (1) ◽  
pp. 131-137 ◽  
Author(s):  
W. B. Roberts ◽  
G. K. Serovy ◽  
D. M. Sandercock
Keyword(s):  
Boundary Layer ◽  
Layer Thickness ◽  
Boundary Layer Thickness ◽  
Axial Compressor ◽  
Tip Clearance ◽  
Blade Element Theory ◽  
Wall Boundary Layer ◽  
Wall Boundary ◽  
Flow Effects ◽  
End Wall

A model of the spanwise variation of the 3-D flow effects on deviation is proposed for middle-stage rotors and stators. This variation is taken as the difference above or below that predicted by blade element theory at any spanwise location. It was found that the stator variation is strongly affected by the end-wall boundary-layer thickness as well as camber, solidity, and blade channel aspect ratio. Rotor variation was found to depend on end-wall boundary layer thickness and tip clearance normalized by blade span. If these parameters are known or can be calculated, the models provide a reasonable approximation to the spanwise variation of deviation for middle compressor stages operating at low to high subsonic inlet Mach numbers.

Annulus Wall Boundary-Layer Measurements in a Four-Stage Compressor

1986 ◽  
Vol 108 (1) ◽  
pp. 2-6 ◽  
Author(s):  
N. A. Cumpsty
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Layer Thickness ◽  
Boundary Layers ◽  
Boundary Layer Thickness ◽  
Tip Clearance ◽  
The Other ◽  
Wall Boundary Layer ◽  
Multistage Compressors ◽  
Full Design

There are few available measurements of the boundary layers in multistage compressors when the repeating-stage condition is reached. These tests were performed in a small four-stage compressor; the flow was essentially incompressible and the Reynolds number based on blade chord was about 5 • 104. Two series of tests were performed; in one series the full design number of blades were installed, in the other series half the blades were removed to reduce the solidity and double the staggered spacing. Initially it was wished to examine the hypothesis proposed by Smith [1] that staggered spacing is a particularly important scaling parameter for boundary layer thickness; the results of these tests and those of Hunter and Cumpsty [2] tend to suggest that it is tip clearance which is most potent in determining boundary-layer integral thicknesses. The integral thicknesses agree quite well with those published by Smith.

EFFECTS OF BOUNDARY-LAYER THICKNESS ON UNSTEADY FLOW CHARACTERISTICS INSIDE OPEN CAVITIES AT SUBSONIC AND TRANSONIC SPEEDS

2012 ◽  
Vol 19 ◽  
pp. 206-213
Author(s):  
DANG-GUO YANG ◽  
JIAN-QIANG LI ◽  
ZHAO-LIN FAN ◽  
XIN-FU LUO
Keyword(s):  
Boundary Layer ◽  
Unsteady Flow ◽  
Layer Thickness ◽  
Boundary Layer Thickness ◽  
Sound Pressure ◽  
Flow Characteristics ◽  
Open Cavity ◽  
Aerodynamic Noise ◽  
Sustained Oscillation ◽  
Cavity Depth

An experimental study was conducted in a 0.6m by 0.6m wind-tunnel to analyze effects of boundary-layer thickness on unsteady flow characteristics inside a rectangular open cavity at subsonic and transonic speeds. The sound pressure level (SPL) distributions at the centerline of the cavity floor and Sound pressure frequency spectrum (SPFS) characteristics on some measurement positions presented herein was obtained with cavity length-to-depth ratio (L/D) of 8 over Mach numbers (Ma) of 0.6 and 1.2 at a Reynolds numbers (Re) of 1.23 × 107 and 2.02 × 107 per meter under different boundary-layer thickness to cavity-depth ratios (δ/D). The experimental angle of attack, yawing and rolling angles were 0°. The results indicate that decrease in δ/D leads to severe flow separation and unsteady pressure fluctuation, which induces increase in SPL at same measurement points inside the cavity at Ma of 0.6. At Ma of 1.2, decrease in δ/D results in enhancing compressible waves. Generally, decrease in δ/D induces more flow self-sustained oscillation frequencies. It also makes severer aerodynamic noise inside the open cavity.

Sign in / Sign up

Export Citation Format

Share Document