On near-wall hot-wire measurements

2000 ◽  
Vol 29 (5) ◽  
pp. 448-460 ◽  
Author(s):  
B. C. Khoo ◽  
Y. T. Chew ◽  
C. J. Teo
Keyword(s):  
Hot Wire ◽  
2000 ◽  
Author(s):  
Li Wenzhong ◽  
B. C. Khoo ◽  
Xu Diao

Abstract The present paper is to determine the correction of hot-wire measurements when it is used to measure the shear flows region very close to the non-conducting wall. By numerical simulation of the Navier-Stokes and energy equations using the control volume method, we found that reasonably deployed grid distribution could largely reduce the computational domain size (for a typical Reynolds number for hot-wire near-wall measurements 4.0×10−3∼1.2, the domain boundary placing 650 diameters from the cylinder in front, rear and top is fair enough for accurate simulation, other than the domain boundary which places the 2000 diameters from the cylinder in front and top, and 3000 diameters from the cylinder in rear), and obtain the similar accuracy results for the correction of hot-wire measurements in the near-wall region. Numerical simulation results also show that, only taking the εf,εw (the maximum difference between the respective values of stream function and vorticity on successive iterations) as the criterion for convergence without judge to convergence of the temperature field seems not enough to obtain a convergent simulation result. This may be the possible reason which caused the discrepancy between the simulation results for hot-wire correction when using hot wire to measure the shear flows very close to the non-conducting wall.


2011 ◽  
Vol 677 ◽  
pp. 179-203 ◽  
Author(s):  
I. JACOBI ◽  
B. J. McKEON

The zero-pressure-gradient turbulent boundary layer over a flat plate was perturbed by a short strip of two-dimensional roughness elements, and the downstream response of the flow field was interrogated by hot-wire anemometry and particle image velocimetry. Two internal layers, marking the two transitions between rough and smooth boundary conditions, are shown to represent the edges of a ‘stress bore’ in the flow field. New scalings, based on the mean velocity gradient and the third moment of the streamwise fluctuating velocity component, are used to identify this ‘stress bore’ as the region of influence of the roughness impulse. Spectral composite maps reveal the redistribution of spectral energy by the impulsive perturbation – in particular, the region of the near-wall peak was reached by use of a single hot wire in order to identify the significant changes to the near-wall cycle. In addition, analysis of the distribution of vortex cores shows a distinct structural change in the flow associated with the perturbation. A short spatially impulsive patch of roughness is shown to provide a vehicle for modifying a large portion of the downstream flow field in a controlled and persistent way.


2009 ◽  
Vol 635 ◽  
pp. 103-136 ◽  
Author(s):  
N. HUTCHINS ◽  
T. B. NICKELS ◽  
I. MARUSIC ◽  
M. S. CHONG

Careful reassessment of new and pre-existing data shows that recorded scatter in the hot-wire-measured near-wall peak in viscous-scaled streamwise turbulence intensity is due in large part to the simultaneous competing effects of the Reynolds number and viscous-scaled wire length l+. An empirical expression is given to account for these effects. These competing factors can explain much of the disparity in existing literature, in particular explaining how previous studies have incorrectly concluded that the inner-scaled near-wall peak is independent of the Reynolds number. We also investigate the appearance of the so-called outer peak in the broadband streamwise intensity, found by some researchers to occur within the log region of high-Reynolds-number boundary layers. We show that the ‘outer peak’ is consistent with the attenuation of small scales due to large l+. For turbulent boundary layers, in the absence of spatial resolution problems, there is no outer peak up to the Reynolds numbers investigated here (Reτ = 18830). Beyond these Reynolds numbers – and for internal geometries – the existence of such peaks remains open to debate. Fully mapped energy spectra, obtained with a range of l+, are used to demonstrate this phenomenon. We also establish the basis for a ‘maximum flow frequency’, a minimum time scale that the full experimental system must be capable of resolving, in order to ensure that the energetic scales are not attenuated. It is shown that where this criterion is not met (in this instance due to insufficient anemometer/probe response), an outer peak can be reproduced in the streamwise intensity even in the absence of spatial resolution problems. It is also shown that attenuation due to wire length can erode the region of the streamwise energy spectra in which we would normally expect to see kx−1 scaling. In doing so, we are able to rationalize much of the disparity in pre-existing literature over the kx−1 region of self-similarity. Not surprisingly, the attenuated spectra also indicate that Kolmogorov-scaled spectra are subject to substantial errors due to wire spatial resolution issues. These errors persist to wavelengths far beyond those which we might otherwise assume from simple isotropic assumptions of small-scale motions. The effects of hot-wire length-to-diameter ratio (l/d) are also briefly investigated. For the moderate wire Reynolds numbers investigated here, reducing l/d from 200 to 100 has a detrimental effect on measured turbulent fluctuations at a wide range of energetic scales, affecting both the broadband intensity and the energy spectra.


1999 ◽  
Vol 26 (5) ◽  
pp. 475-477 ◽  
Author(s):  
C. F. Lange ◽  
F. Durst ◽  
M. Breuer
Keyword(s):  
Hot Wire ◽  

Author(s):  
Zi-Liang Zhang ◽  
Ming-Ming Zhang ◽  
Chang Cai ◽  
Yu Cheng

Riblet is one of the most promising passive drag reduction techniques in turbulent flows. In this paper, hot-wire measurements on a turbulent boundary layer perturbed by a drag-reducing riblet surface are carried out to further understand the riblet effects on the turbulent flows and the drag reduction mechanism. Compared with the smooth case, different energy variations in the near-wall region and the logarithmic region are observed over riblets. Then, by using a spectral filter of a given wavelength, the time series of the hot-wire data are decomposed into large- and small-scale components. It is indicated that large-scale structures in the logarithmic region impose a footprint (amplitude modulating effect) on the near-wall small-scale structures. By quantifying this footprint, it is found that the interactions between large- and small-scale structures over riblets are weakened in the near-wall region. Furthermore, the bursting process of large and small scales is studied. For both large- and small-scale structures, a shorter bursting duration and a higher bursting frequency are observed over the riblet surface, which indicates that riblets impede the formation of large- and small-scale bursting events. The flow physics behind these phenomena are also discussed in detail.


Sign in / Sign up

Export Citation Format

Share Document