Pressure drop and heat transfer associated with flows moving laminarly in straight ducts of irregular, singly connected cross-sections

1997 ◽  
Vol 32 (3) ◽  
pp. 193-197 ◽  
Author(s):  
A. Campo ◽  
J. C. Morales ◽  
A. E. Larreteguy
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Cross Sections

scholarly journals Numerical Analysis of Microchannels Designed for Heat Sinks

2021 ◽  
Author(s):  
Matthew McCormack ◽  
Fengzhou Fang ◽  
Jufan Zhang
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Cross Sections ◽  
High Performance ◽  
Three Dimensional ◽  
Heat Fluxes ◽  
Dean Flow ◽  
System Pressure ◽  
Spatial Frequencies ◽  
Geometric Variation

AbstractConjugate heat transfer is numerically investigated using a three-dimensional computational fluid dynamics approach in various microchannel geometries to identify a high-performance cooling method for piezoelectric ceramic stacks and spindle units in high-precision machines. Straight microchannels with rectangular cross sections are first considered, showing the performance limitations of decreasing the size of the microchannels, so other solutions are needed for high applied heat fluxes. Next, many microchannel designs, focusing on streamwise geometric variation, are compared to straight channels to assess their performances. Sinusoidally varying channels produce the highest heat transfer rates of those studied. Thus, their optimization is considered at a channel width and height of 35 and 100 μm, respectively. Heat transfer increases as the amplitude and spatial frequencies of the channels increase due to increased interfacial surface area and enhanced Dean flow. The highest performance efficiencies are observed at intermediate levels of amplitude and frequency, with efficiency decreasing as these geometric parameters are increased further at the onset of flow separation. The sinusoidal channel geometries are then optimized with respect to minimizing the system’s pressure drop for all applied heat fluxes between 5690 and 6510 kW/m2. Doing so created an optimal geometry curve and showed that all geometries in this region had amplitudes close to 40 μm. Therefore, imposing a fixed heat flux requirement for a case study of cooling piezoelectric ceramics, the optimized sinusoidal geometry decreases the system pressure drop by 79% relative to a straight channel while maintaining a larger minimum feature size.

scholarly journals Ice slurry flow and heat transfer during flow through tubes of rectangular and slit cross-sections

2014 ◽  
Vol 35 (3) ◽  
pp. 171-190
Author(s):  
Beata Niezgoda-Żelasko ◽  
Jerzy Żelasko
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Cross Sections ◽  
Heat Transfer Process ◽  
Solid Particles ◽  
Ice Slurry ◽  
Slurry Flow ◽  
Transfer Coefficients ◽  
Laminar And Turbulent Flow ◽  
Flow Through

Abstract The paper presents the results of experimental research of pressure drop and heat transfer coefficients of ice slurry during its flow through tubes of rectangular and slit cross-sections. Moreover, the work discusses the influence of solid particles, type of motion and cross-section on the changes in the pressure drop and heat transfer coefficient. The analysis presented in the paper allows for identification of the criterial relations used to calculate the Fanning factor and the Nusselt number for laminar and turbulent flow, taking into account elements such as phase change, which accompanies the heat transfer process. Ice slurry flow is treated as a generalized flow of a non-Newtonian fluid.

Thermo-Fluidic Characteristics in a Cross-Linked Silicon Microchannel Heat Sink

2007 ◽  
Author(s):  
R. Muwanga ◽  
I. Hassan
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Cross Sections ◽  
Heat Sink ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Working Fluid ◽  
Microchannel Heat Sink ◽  
Significant Difference ◽  
The Cross

This paper presents the flow and heat transfer characteristics in a cross-linked silicon microchannel heat sink. The heat sink is composed of 45 channels, 270 μm wide × 285 μm tall in a silicon substrate formed via deep reactive ion etching. A detailed discussion of the pressure drop data reduction is described, including characterization of the channel cross-sections and methods to account for inlet and exit loss coefficients. No significant difference is observed in the pressure drop measurements between the cross-linked and standard heat sinks flowing air and water. The use of un-encapsulated liquid crystal thermography was successfully utilized to obtain local heat transfer data with FC-72 as the working fluid. The heat transfer results show inflections in the thermal profile due to the cross-links.

Numerical investigation of the effect of water/Al2O3 nanofluid on heat transfer in trapezoidal, sinusoidal and stepped microchannels

2019 ◽  
Vol 30 (5) ◽  
pp. 2439-2465 ◽  
Author(s):  
Vahid Jaferian ◽  
Davood Toghraie ◽  
Farzad Pourfattah ◽  
Omid Ali Akbari ◽  
Pouyan Talebizadehsardari
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Cross Section ◽  
Cross Sections ◽  
Volume Fraction ◽  
Pure Water ◽  
Circular Cross Section ◽  
Reynolds Numbers ◽  
Two Phase ◽  
Content Type

Purpose The purpose of this study is three-dimensional flow and heat transfer investigation of water/Al2O3 nanofluid inside a microchannel with different cross-sections in two-phase mode. Design/methodology/approach The effect of microchannel walls geometry (trapezoidal, sinusoidal and stepped microchannels) on flow characteristics and also changing circular cross section to trapezoidal cross section in laminar flow at Reynolds numbers of 50, 100, 300 and 600 were investigated. In this study, two-phase water/Al2O3 nanofluid is simulated by the mixture model, and the effect of volume fraction of nanoparticles on performance evaluation criterion (PEC) is studied. The accuracy of obtained results was compared with the experimental and numerical results of other similar papers. Findings Results show that in flow at lower Reynolds numbers, sinusoidal walls create a pressure drop in pure water flow which improves heat transfer to obtain PEC < 1. However, in sinusoidal and stepped microchannel with higher Reynolds numbers, PEC > 1. Results showed that the stepped microchannel had higher pressure drop, better thermal performance and higher PEC than other microchannels. Originality/value Review of previous studies showed that existing papers have not compared and investigated nanofluid in a two-phase mode in inhomogeneous circular, stepped and sinusoidal cross and trapezoidal cross-sections by considering the effect of changing channel shape, which is the aim of the present paper.

Numerical investigation of several twisted tubes with non-conventional tube cross sections on heat transfer and pressure drop

2019 ◽  
Vol 140 (3) ◽  
pp. 1555-1568 ◽  
Author(s):  
B. Indurain ◽  
D. Uystepruyst ◽  
F. Beaubert ◽  
S. Lalot ◽  
Á. Helgadóttir
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Numerical Investigation ◽  
Cross Sections ◽  
Twisted Tubes

Efficiency assessment of using graphene nanoplatelets-silver/water nanofluids in microchannel heat sinks with different cross-sections for electronics cooling

2019 ◽  
Vol 30 (1) ◽  
pp. 347-372 ◽  
Author(s):  
Marjan Goodarzi ◽  
Iskander Tlili ◽  
Zhe Tian ◽  
Mohammad Reza Safaei
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Pressure Drop ◽  
Friction Factor ◽  
Cross Sections ◽  
Graphene Nanoplatelets ◽  
Heat Sinks ◽  
Pumping Power ◽  
Content Type

Purpose This study aims to model the nanofluid flow in microchannel heat sinks having the same length and hydraulic diameter but different cross-sections (circular, trapezoidal and square). Design/methodology/approach The nanofluid is graphene nanoplatelets-silver/water, and the heat transfer in laminar flow was investigated. The range of coolant Reynolds number in this investigation was 200 ≤ Re ≤ 1000, and the concentrations of nano-sheets were from 0 to 0.1 vol. %. Findings Results show that higher temperature leads to smaller Nusselt number, pressure drop and pumping power, and increasing solid nano-sheet volume fraction results in an expected increase in heat transfer. However, the influence of temperature on the friction factor is insignificant. In addition, by increasing the Reynolds number, the values of pressure drop, pumping power and Nusselt number augments, but friction factor diminishes. Research limitations/implications Data extracted from a recent experimental work were used to obtain thermo-physical properties of nanofluids. Originality/value The effects of temperature, microchannel cross-section shape, the volume concentration of nanoparticles and Reynolds number on thermal and hydraulics behavior of the nanofluid were investigated. Results are presented in terms of velocity, Nusselt number, pressure drop, friction loss and pumping power in various conditions. Validation of the model against previous papers showed satisfactory agreement.

Sign in / Sign up

Export Citation Format

Share Document