On thermal boundary layer of a non-Newtonian fluid on a power-law stretched surface of variable temperature with suction or injection

2001 ◽  
Vol 37 (4-5) ◽  
pp. 459-465 ◽  
Author(s):  
Bourhan Tashtoush ◽  
Z. Kodah ◽  
A. Al-Ghasem
Keyword(s):  
Boundary Layer ◽  
Newtonian Fluid ◽  
Power Law ◽  
Thermal Boundary Layer ◽  
Variable Temperature ◽  
Suction Or Injection

Experimental studies of the viscous boundary layer properties in turbulent Rayleigh–Bénard convection

2008 ◽  
Vol 605 ◽  
pp. 79-113 ◽  
Author(s):  
CHAO SUN ◽  
YIN-HAR CHEUNG ◽  
KE-QING XIA
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Shear Stress ◽  
Rayleigh Number ◽  
Power Law ◽  
Thermal Boundary Layer ◽  
Viscous Sublayer ◽  
Viscous Boundary Layer ◽  
Velocity Boundary Layer ◽  
Viscous Boundary

We report high-resolution measurements of the properties of the velocity boundary layer in turbulent thermal convection using the particle image velocimetry (PIV) technique and measurements of the temperature profiles and the thermal boundary layer. Both velocity and temperature measurements were made near the lower conducting plate of a rectangular convection cell using water as the convecting fluid, with the Rayleigh number Ra varying from 109 to 1010 and the Prandtl number Pr fixed at 4.3. From the measured profiles of the horizontal velocity we obtain the viscous boundary layer thickness δυ. It is found that δυ follows the classical Blasius-like laminar boundary layer in the present range of Ra, and it scales with the Reynolds number Re as δυ/H = 0.64Re−0.50±0.03 (where H is the cell height). While the measured viscous shear stress and Reynolds shear stress show that the boundary layer is laminar for Ra < 2.0 × 1010, two independent extrapolations, one based on velocity measurements and the other on velocity and temperature measurements, both indicate that the boundary layer will become turbulent at Ra ~ 1013. Just above the thermal boundary layer but within the mixing zone, the measured temperature r.m.s. profiles σT(z) are found to follow either a power law or a logarithmic behaviour. The power-law fitting may be slightly favoured and its exponent is found to depend on Ra and varies from −0.6 to −0.77, which is much larger than the classical value of −1/3. In the same region, the measured profiles of the r.m.s. vertical velocity σw(z) exhibit a much smaller scaling range and are also consistent with either a power-law or a logarithmic behaviour. The Reynolds number dependence of several wall quantities is also measured directly. These are the wall shear stress τw ~ Re1.55, the viscous sublayer δw ~ Re−0.91, the friction velocity uτ ~ Re0.80, and the skin-friction coefficient cf ~ Re−0.34. All of these scaling properties are very close to those predicted for a classical Blasius-type laminar boundary layer, except that of cf. Similar to classical shear flows, a viscous sublayer is also found to exist in the present system despite the presence of a nested thermal boundary layer. However, velocity profiles normalized by wall units exhibit no obvious logarithmic region, which is likely to be a result of the very limited distance between the edge of the viscous sublayer and the position of the maximum velocity. Compared to traditional shear flows, the peak position of the wall-unit-normalized r.m.s. profiles is found to be closer to the plate (at z+ = z/δw ≃ 5). Our overall conclusion is that a Blasius-type laminar boundary condition is a good approximation for the velocity boundary layer in turbulent thermal convection for the present range of Rayleigh number and Prandtl number.

An analysis of the characteristics of the thermal boundary layer in power law fluid

2008 ◽  
Vol 17 (3) ◽  
pp. 233-237 ◽  
Author(s):  
Hao Zhang ◽  
Xinxin Zhang ◽  
Liancun Zheng
Keyword(s):  
Boundary Layer ◽  
Power Law ◽  
Thermal Boundary Layer ◽  
Power Law Fluid
Sign in / Sign up

Export Citation Format

Share Document