Mechanical-pulse hardening of electrochemical composite coatings

2000 ◽  
Vol 36 (1) ◽  
pp. 118-121
Author(s):  
R. S. Mardarevych ◽  
V. I. Kyryliv ◽  
V. I. Pokhmurs'kyi
Keyword(s):  
Composite Coatings ◽  
Pulse Hardening ◽  
Mechanical Pulse

Microwave Absorbing Properties of Carbon Fibers Modified with BN/SiC Composite Coatings

2014 ◽  
Vol 29 (10) ◽  
pp. 1093 ◽  
Author(s):  
ZHOU Wei ◽  
XIAO Peng ◽  
LI Yang ◽  
LUO Heng ◽  
HONG Wen
Keyword(s):  
Carbon Fibers ◽  
Composite Coatings ◽  
Microwave Absorbing Properties ◽  
Microwave Absorbing

Laser cladding Ni-base composite coatings reinforced by in-situ synthesized multiple carbide particles

2008 ◽  
Author(s):  
Ruiquan Kang ◽  
Mingxing Ma ◽  
Wenjin Liu ◽  
Minlin Zhong ◽  
Yide Kan ◽  
...  
Keyword(s):  
Laser Cladding ◽  
Composite Coatings ◽  
Base Composite ◽  
Carbide Particles

Super hard WC-Cr composite coatings: An approach to potential wear applications

2016 ◽  
Vol 58 (10) ◽  
pp. 864-869
Author(s):  
Orkut Sancakoğlu ◽  
Erdal Çelik
Keyword(s):  
Composite Coatings

Evaluation of the Diamond Particle Content in Ni-P Nano-Composite Coatings

2016 ◽  
Vol 53 (3) ◽  
pp. 144-160
Author(s):  
D. Dietrich ◽  
A. Eilert ◽  
D. Nickel ◽  
T. Lampke
Keyword(s):  
Composite Coatings ◽  
Diamond Particle ◽  
Particle Content ◽  
Nano Composite

Studies and Research on the Corrosion Behavior of Ni-Al2O3 Compound Coatings Obtained by Electrochemical Methods

2020 ◽  
Vol 43 (3) ◽  
pp. 21-25
Author(s):  
Simona BOICIUC ◽  
◽  
◽  
Keyword(s):  
Corrosion Resistance ◽  
Corrosion Behavior ◽  
Corrosion Behaviour ◽  
Composite Coatings ◽  
Point Of View ◽  
Electrochemical Methods ◽  
Dispersed Phase ◽  
Nickel Matrix ◽  
Technical Alumina ◽  
Compound Coatings

The undertaken research which is described in this paper aims at the corrosion behaviour of composite coatings in nickel matrix using as dispersed phase technical alumina with dimensions of 5 μm and their characterization from a microstructural point of view. The corrosion resistance in the saline fog of the coatings is influenced by the microstructure, the stresses developed in the layer and the roughness.

Chemical deposition of hard composite coatings Ni–Cu–P–Cr2O3

2020 ◽  
pp. 179-181
Author(s):  
A.A. Abrashov A.A. ◽  
E.G. Vinokurov ◽  
M.A. Egupova ◽  
V.D. Skopintsev
Keyword(s):  
Chromium Oxide ◽  
Alkaline Solution ◽  
Composite Coatings ◽  
Chemical Deposition ◽  
Alkaline Solutions ◽  
Functional Surface ◽  
Heat Treated ◽  
Weakly Acid Solution ◽  
Coating Composition ◽  
Weakly Acidic Solution

The technological (deposition rate, coating composition) and functional (surface roughness, microhardness) characteristics of chemical composite coatings Ni—Cu—P—Cr2O3 obtained from weakly acidic and slightly alkaline solutions are compared. It is shown that coatings deposited from slightly alkaline solution contain slightly less phosphorus and chromium oxide than coatings deposited from weakly acid solution (2...3 % wt. phosphorus and up to 3.4 % wt. chromium oxide), formed at higher rate (24...25 microns per 1 hour of deposition at temperature of 80 °C), are characte rized by lower roughness and increased microhardness. The Vickers microhardness at 0.05 N load of composite coatings obtained from slightly alkaline solution and heat-treated at 400 °C for 1 hour is 13.5...15.2 GPa, which is higher than values for coatings deposited made of weakly acidic solution. The maximum microhardness of coatings is achieved at concentration 20 g/l of Cr2O3 particles. The technology of chemical deposition of Ni—Cu—P—Cr2O3 coatings formed in slightly alkaline solution is promising for obtaining of materials with increased hardness and wear resistance.

scholarly journals Preparation of MCrAlY–Al2O3 Composite Coatings with Enhanced Oxidation Resistance through a Novel Powder Manufacturing Process

2019 ◽  
Vol 28 (3) ◽  
pp. 433-443 ◽  
Author(s):  
Mingwen Bai ◽  
Bo Song ◽  
Liam Reddy ◽  
Tanvir Hussain
Keyword(s):  
Oxidation Resistance ◽  
Manufacturing Process ◽  
Composite Powder ◽  
Composite Coatings ◽  
Submicron Particles ◽  
Second Phase ◽  
Mcraly Coatings ◽  
Powder Feedstock ◽  
Enhanced Oxidation ◽  
Powder Manufacturing

Abstract MCrAlY–Al2O3 composite coatings were prepared by high-velocity oxygen fuel thermal spraying with bespoke composite powder feedstock for high-temperature applications. Powder processing via a suspension route was employed to achieve a fine dispersion of α-Al2O3 submicron particles on the MCrAlY powder surface. This was, however, compromised by ~ 50% less flowability of the feedstock during spraying. Nevertheless, the novel powder manufacturing process introduced in this study has shown potential as an alternative route to prepare tailored composite powder feedstock for the production of metal matrix composites. In addition, the newly developed MCrAlY–Al2O3 composite coatings exhibited superior oxidation resistance, compared to conventional MCrAlY coatings, with the formation of nearly exclusively Al2O3 scale after isothermal oxidation at 900 °C for 10 h. The addition of α-Al2O3 particles in the MCrAlY coatings as a second phase was found to have promoted the formation of YAG oxides (YxAlyOz) during spraying and also accelerated the outwards diffusion of Al, which resulted in enhanced oxidation resistance.

Sign in / Sign up

Export Citation Format

Share Document