Influences of material parameters and microstructure on superplastic forming

1982 ◽  
Vol 13 (5) ◽  
pp. 733-743 ◽  
Author(s):  
A. K. Ghosh ◽  
C. H. Hamilton
Keyword(s):  
Superplastic Forming ◽  
Material Parameters

Cavity Nucleation in AL 5083 Alloys

1999 ◽  
Vol 601 ◽  
Author(s):  
N. Chandra ◽  
Z. Chen
Keyword(s):  
Electron Microscopy ◽  
Rolling Direction ◽  
Interfacial Strength ◽  
Superplastic Forming ◽  
Simplified Model ◽  
Hard Phase ◽  
Cavity Nucleation ◽  
Material Parameters ◽  
State Of Stress ◽  
Process Material

AbstractIn this paper we address the controversial issue of nucleation of cavities in Al 5083 alloys. We focus on the origin of cavities during the manufacture of these alloys into SPF (superplastic forming) sheet form. Experimental observations on the pre-existing cavities in this alloy are made using optical and electron microscopy. The effects of rolling direction and state of stress during superplastic deformations on the formation of cavities are also discussed. Numerical simulations of the sheet manufacturing process are carried out to understand the effect of hard phase/matrix, mechanical properties and interfacial strength on the origin of cavities. Based on the numerical results, a simplified model relating the process, material parameters and the cavity nucleation is presented.

scholarly journals Determination of Material Parameters during Superplastic Forming of AA 5086 Alloy

2014 ◽  
Vol 97 ◽  
pp. 1379-1386 ◽  
Author(s):  
S. Ramesh Babu ◽  
S. Deivanayagam ◽  
M. Aravind
Keyword(s):  
Superplastic Forming ◽  
Material Parameters

A very rapid in situ Kikuchi technique to determine relative crystal misorientation

1988 ◽  
Vol 46 ◽  
pp. 830-831
Author(s):  
J. I. Bennetch
Keyword(s):  
Electron Beam ◽  
Analytical Techniques ◽  
Superplastic Forming ◽  
The Other ◽  
Kikuchi Pattern ◽  
Kikuchi Line ◽  
Line Analysis

In a recent study of the superplastic forming (SPF) behavior of certain Al-Li-X alloys, the relative misorientation between adjacent (sub)grains proved to be an important parameter. It is well established that the most accurate way to determine misorientation across boundaries is by Kikuchi line analysis. However, the SPF study required the characterization of a large number of (sub)grains in each sample to be statistically meaningful, a very time-consuming task even for comparatively rapid Kikuchi analytical techniques.In order to circumvent this problem, an alternate, even more rapid in-situ Kikuchi technique was devised, eliminating the need for the developing of negatives and any subsequent measurements on photographic plates. All that is required is a double tilt low backlash goniometer capable of tilting ± 45° in one axis and ± 30° in the other axis. The procedure is as follows. While viewing the microscope screen, one merely tilts the specimen until a standard recognizable reference Kikuchi pattern is centered, making sure, at the same time, that the focused electron beam remains on the (sub)grain in question.

“Cavity” formation in superplastically deformed aluminium alloys

1990 ◽  
Vol 48 (4) ◽  
pp. 958-959
Author(s):  
A. Cziráki ◽  
E. Ková-csetényi ◽  
T. Torma ◽  
T. Turmezey
Keyword(s):  
Grain Boundaries ◽  
Aluminium Alloys ◽  
Superplastic Deformation ◽  
Volume Fraction ◽  
Superplastic Forming ◽  
Polished Surface ◽  
Cavity Formation ◽  
Stress Concentrations ◽  
Electron Microscopic ◽  
Commercial Aluminium

It is known that the formation of cavities during superplastic deformation can be correlated with the development of stress concentrations at irregularities along grain boundaries such as particles, ledges and triple points. In commercial aluminium alloys Al-Fe-Si particles or other coarse constituents may play an important role in cavity formation.Cavity formation during superplastic deformation was studied by optical metallography and transmission scanning electron microscopic investigations on Al-Mg-Si and Al-Mg-Mn alloys. The structure of particles was characterized by selected area diffraction and X-ray micro analysis. The volume fraction of “voids” was determined on mechanically polished surface.It was found by electron microscopy that strongly deformed regions are formed during superplastic forming at grain boundaries and around coarse particles.According to electron diffraction measurements these areas consist of small micro crystallized regions. See Fig.l.Comparing the volume fraction and morphology of cavities found by optical microscopy a good correlation was established between that of micro crystalline regions.

Lifetime Prediction of Tires with Regard to Oxidative Aging5

2008 ◽  
Vol 36 (1) ◽  
pp. 63-79 ◽  
Author(s):  
L. Nasdala ◽  
Y. Wei ◽  
H. Rothert ◽  
M. Kaliske
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Temperature Distribution ◽  
Superposition Principle ◽  
Accelerated Aging ◽  
Material Model ◽  
Aging Behavior ◽  
Element Analysis ◽  
Material Parameters ◽  
Reaction Processes

Abstract It is a challenging task in the design of automobile tires to predict lifetime and performance on the basis of numerical simulations. Several factors have to be taken into account to correctly estimate the aging behavior. This paper focuses on oxygen reaction processes which, apart from mechanical and thermal aspects, effect the tire durability. The material parameters needed to describe the temperature-dependent oxygen diffusion and reaction processes are derived by means of the time–temperature–superposition principle from modulus profiling tests. These experiments are designed to examine the diffusion-limited oxidation (DLO) effect which occurs when accelerated aging tests are performed. For the cord-reinforced rubber composites, homogenization techniques are adopted to obtain effective material parameters (diffusivities and reaction constants). The selection and arrangement of rubber components influence the temperature distribution and the oxygen penetration depth which impact tire durability. The goal of this paper is to establish a finite element analysis based criterion to predict lifetime with respect to oxidative aging. The finite element analysis is carried out in three stages. First the heat generation rate distribution is calculated using a viscoelastic material model. Then the temperature distribution can be determined. In the third step we evaluate the oxygen distribution or rather the oxygen consumption rate, which is a measure for the tire lifetime. Thus, the aging behavior of different kinds of tires can be compared. Numerical examples show how diffusivities, reaction coefficients, and temperature influence the durability of different tire parts. It is found that due to the DLO effect, some interior parts may age slower even if the temperature is increased.

Sign in / Sign up

Export Citation Format

Share Document