Influence of reinforcement volume fraction and size on the microstructure and abrasion wear resistance of hot Isostatic pressed white iron matrix composites

1996 ◽  
Vol 27 (12) ◽  
pp. 4171-4181 ◽  
Author(s):  
E. Pagounis ◽  
V. K. Lindroos ◽  
M. Talvitie
Keyword(s):  
Wear Resistance ◽  
Volume Fraction ◽  
Matrix Composites ◽  
White Iron ◽  
Iron Matrix ◽  
Abrasion Wear

Infiltration Casting and In Situ Fabrication of NbC Particulates – Reinforced Iron Matrix Composites

2011 ◽  
Vol 284-286 ◽  
pp. 269-272
Author(s):  
Li Sheng Zhong ◽  
Yun Hua Xu ◽  
Na Na Wang ◽  
Xiao Jie Liu ◽  
Fang Xia Ye ◽  
...  
Keyword(s):  
Wear Resistance ◽  
Volume Fraction ◽  
Niobium Carbide ◽  
Wear Testing ◽  
Matrix Composites ◽  
X Ray Diffraction ◽  
Iron Matrix ◽  
Micro Cracks ◽  
Particulate Reinforced

Niobium carbide (NbC) particulates -reinforced iron matrix composites were prepared by in- situ fabrication method combining an infiltration casting with a subsequent heat treatment. The microstructure and wear-resistance of NbC particulate-reinforced iron matrix composites were studied using scanning electron microscopy, X-ray diffraction, and wear testing. The results indicate that at 1172 °C for 3 hours NbC particulate-reinforced iron matrix composites were fabricated, and the size of NbC reinforcement was 0.3–3.5 μm. The relative wear resistance of the composites was 5.4 times higher than that of gray cast iron under a 20 N load. This was achieved at 22 % NbC volume fraction. Wear of the composites manifests as grooves, broken carbide particulates and some micro-cracks.

scholarly journals Improvement in Hardness and Wear Behaviour of Iron-Based Mn–Cu–Sn Matrix for Sintered Diamond Tools by Dispersion Strengthening

Materials ◽  
2021 ◽  
Vol 14 (7) ◽  
pp. 1774
Author(s):  
Elżbieta Cygan-Bączek ◽  
Piotr Wyżga ◽  
Sławomir Cygan ◽  
Piotr Bała ◽  
Andrzej Romański
Keyword(s):  
Wear Resistance ◽  
Metal Matrix Composites ◽  
Metal Matrix ◽  
Base Material ◽  
Wear Behaviour ◽  
Matrix Composites ◽  
Diamond Tools ◽  
Abrasion Wear ◽  
Sintered Diamond ◽  
Abrasive Stone

The work presents the possibility of fabricating materials for use as a matrix in sintered metallic-diamond tools with increased mechanical properties and abrasion wear resistance. In this study, the effect of micro-sized SiC, Al2O3, and ZrO2 additives on the wear behaviour of dispersion-strengthened metal-matrix composites was investigated. The development of metal-matrix composites (based on Fe–Mn–Cu–Sn–C) reinforced with micro-sized particles is a new approach to the substitution of critical raw materials commonly used for the matrix in sintered diamond-impregnated tools used for the machining of abrasive stone and concrete. The composites were prepared using spark plasma sintering (SPS). Apparent density, microstructural features, phase composition, Young’s modulus, hardness, and abrasion wear resistance were determined. An increase in the hardness and wear resistance of the dispersion-strengthened composites as compared to the base material (Fe–Mn–Cu–Sn–C) and the commercial alloy Co-20% WC provides metallic-diamond tools with high-performance properties.

In Situ Production of (Fe,Cr)7C3 Particulate Bundles Reinforced Iron Matrix Composites

2012 ◽  
Vol 602-604 ◽  
pp. 456-459
Author(s):  
Jing Lai Tian ◽  
Fang Xia Ye ◽  
Li Sheng Zhong ◽  
Yun Hua Xu
Keyword(s):  
Heat Treatment ◽  
Wear Resistance ◽  
White Cast Iron ◽  
Treatment Time ◽  
Reference Sample ◽  
Chemical Compositions ◽  
Matrix Composites ◽  
Iron Matrix ◽  
Pin On Disc

In-situ production of (Fe,Cr)7C3 particulate bundles -reinforced iron matrix composite was prepared by infiltration casting between Cr wires and white cast iron at 1200°C plus subsequent heat treatment. The composites under different heat treatment times were comparatively characterized by scanning electron microscopy (SEM) and pin-on-disc wear resistance tests. The results show that the area of the particle bundles gradually increases with the heat treatment time increasing, and the chemical compositions change from eutectic to hypoeutectic, the morphologies of the reinforcements present chrysanthemum-shaped, granular and intercrystalline eutectics. Under 5 N loads, the composites appear excellent wear resistance, which is 36 times for the reference sample.

Infiltration Casting and In Situ Fabrication of (Fe,Cr)7C3 Particulates Bundle – Reinforced Iron Matrix Composites

2011 ◽  
Vol 284-286 ◽  
pp. 273-276
Author(s):  
Li Sheng Zhong ◽  
Yun Hua Xu ◽  
Xin Cheng Liu ◽  
Fang Xia Ye ◽  
Jing Lai Tian ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Wear Resistance ◽  
Cast Iron ◽  
Phase Analysis ◽  
Matrix Composite ◽  
Treatment Process ◽  
Heat Treatment Process ◽  
Matrix Composites ◽  
Iron Matrix

The method of infiltration casting plus heat treatment process employing chromium wires and cast iron applied to in-situ synthesized (Fe,Cr)7C3 particulates bundle reinforced iron matrix composites. The phase analysis, microstructure, microhardness and wear-resistance of composite were observed and measured. The results show that it is possible to fabricate (Fe,Cr)7C3 particulates bundle reinforced iron matrix composite produced by this technology, and a special structure which called particulates bundle was fabricated. (Fe,Cr)7C3 particulates bundle were distributed in the forms of granular, lath-shaped and hexagon-shaped in the particulates bundle. The macrohardness of particulates bundle was 52 HRC, and the relative wear resistance of the composites is 2.3—23 times higher than that of the cast iron.

Wear Characteristics of Particulate Reinforced Metal Matrix Composites Fabricated by a Pressureless Metal Infiltration Process

2006 ◽  
Vol 510-511 ◽  
pp. 234-237 ◽  
Author(s):  
Jae Dong Kim ◽  
Hyung Jin Kim ◽  
Sung Wi Koh
Keyword(s):  
Wear Resistance ◽  
Metal Matrix Composites ◽  
Metal Matrix ◽  
Volume Fraction ◽  
Wear Loss ◽  
Matrix Composites ◽  
Slow Speed ◽  
Infiltration Process ◽  
Sliding Speed ◽  
Metal Infiltration

The effect of size and volume fraction of ceramic particles with sliding speed on the wear properties were investigated for metal matrix composites fabricated by a pressureless metal infiltration process. The particulate metal matrix composites exhibited about 5.5 - 6 times greater wear resistance compared with AC8A alloys at high sliding speed, and by increasing the particle size and decreasing the volume fraction the wear resistance improved. The wear resistance of the metal matrix composites and AC8A alloy represented different aspects: the wear loss of the AC8A alloy increased with sliding speed linearly, whereas, the metal matrix composites displayed more wear loss than the AC8A alloy in the slow-speed region. However, a transition point of wear loss was found in the middle-speed region, which shows the minimum wear loss. Furthermore, wear loss in the high-speed region exhibited almost the same value as the slow-speed region. In terms of wear mechanism, the metal matrix composites showed abrasive wear at a slow to high sliding speed generally. However, the AC8A alloy showed abrasive wear at low sliding speed and adhesive and melt wear at a high sliding speed.

Volume Fraction Dependent Wear Behavior of Titanium-Reinforced Aluminum Matrix Composites Manufactured by Melt Infiltration Casting

2018 ◽  
Vol 141 (2) ◽  
Author(s):  
Ridvan Gecu ◽  
Ahmet Karaaslan
Keyword(s):  
Wear Resistance ◽  
Volume Fraction ◽  
Wear Behavior ◽  
Pure Titanium ◽  
Aluminum Matrix ◽  
Aluminum Matrix Composites ◽  
Matrix Composites ◽  
Melt Infiltration ◽  
Cp Ti ◽  
Melt Infiltration Casting

This study aims to investigate the effect of volume fraction of commercially pure titanium (CP-Ti) on microstructural, mechanical, and tribological features of A356 aluminum matrix composites. Vacuum-assisted melt infiltration casting was performed to produce composites with 50%, 65%, 75%, and 80% CP-Ti contents. CP-Ti sawdusts were assembled under mechanical pressure in order to attain porous one-piece CP-Ti preforms which were infiltrated by A356 melt at 730 °C under 10−5 Pa vacuum atmosphere. TiAl3 layer was formed at the interface between A356 and CP-Ti phases. Owing to increased diffusion time through decreased diffusion path length, both thickness and hardness of TiAl3 phase were increased with increasing CP-Ti ratio, whereas the best wear resistance was obtained at 65% CP-Ti ratio. The main reason for decrease in wear resistance of 75% and 80% CP-Ti reinforced composites was fragmentation of TiAl3 layer during wear process due to its excessively increased brittleness. Strongly bonded TiAl3 phase at the interface provided better wear resistance, while weakly bonded ones caused to multiply wear rate.

scholarly journals Niobium Additions to a 15%Cr–3%C White Iron and Its Effects on the Microstructure and on Abrasive Wear Behavior

Metals ◽  
2019 ◽  
Vol 9 (12) ◽  
pp. 1321 ◽  
Author(s):  
Arnoldo Bedolla-Jacuinde ◽  
Francisco Guerra ◽  
Ignacio Mejia ◽  
Uzzi Vera
Keyword(s):  
Heat Treatment ◽  
Wear Resistance ◽  
Abrasive Wear ◽  
Volume Fraction ◽  
Wear Behavior ◽  
Solidification Process ◽  
White Iron ◽  
Bulk Hardness ◽  
Abrasive Wear Behavior ◽  
Cast Alloys

From the present study, niobium additions of 1.79% and 3.98% were added to a 15% Cr–3% C white iron, and their effects on the microstructure, hardness and abrasive wear were analyzed. The experimental irons were melted in an open induction furnace and cast into sand molds to obtain bars of 45 mm diameter. The alloys were characterized by optical and electron microscopy, and X-ray diffraction. Bulk hardness was measured in the as-cast conditions and after a destabilization heat treatment at 900 °C for 30 min. Abrasive wear resistance tests were undertaken for the different irons according to the ASTM G65 standard in both as-cast and heat-treated conditions under three loads (58, 75 and 93 N). The results show that niobium additions caused a decrease in the carbon content in the alloy and that some carbon is also consumed by forming niobium carbides at the beginning of the solidification process; thus decreasing the eutectic M7C3 carbide volume fraction (CVF) from 30% for the base iron to 24% for the iron with 3.98% Nb. However, the overall carbide content was constant at 30%; bulk hardness changed from 48 to 55 hardness Rockwell C (HRC) and the wear resistance was found to have an interesting behavior. At the lowest load, wear resistance for the base iron was 50% lower than that for the 3.98% Nb iron, which is attributed to the presence of hard NbC. However, at the highest load, the wear behavior was quite similar for all the irons, and it was attributed to a severe carbide cracking phenomenon, particularly in the as-cast alloys. After the destabilization heat treatment, the wear resistance was higher for the 3.98% Nb iron at any load; however, at the highest load, not much difference in wear resistance was observed. Such a behavior is discussed in terms of the carbide volume fraction (CVF), the amount of niobium carbides, the amount of martensite/austenite in matrix and the amount of secondary carbides precipitated during the destabilization heat treatment.

Microstructure and Wear Properties of In Situ Production of (Fe,Cr)7C3 Particulate Bundles Reinforced Iron Matrix Composites

2013 ◽  
Vol 652-654 ◽  
pp. 64-68 ◽  
Author(s):  
Jing Lai Tian ◽  
Fang Xia Ye ◽  
Li Sheng Zhong ◽  
Yun Hua Xu
Keyword(s):  
Heat Treatment ◽  
Wear Resistance ◽  
Treatment Time ◽  
Heat Treatment Time ◽  
Wear Testing ◽  
Dry Sliding Wear ◽  
Matrix Composites ◽  
Wear Properties ◽  
Iron Matrix

In-situ production of (Fe,Cr)7C3 particulate bundles-reinforced iron matrix composites were prepared by infiltration casting between Cr wires and white cast iron at 1200°C plus subsequent heat treatment. The composites prepared under different heat treatment time were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), macrohardness test and pin-on-disc wear resistance test. The results show that the composite is mainly consist of (Fe,Cr)7C3 carbides and γ-Fe. The area of the particulate bundles gradually increases with the increase of heat treatment time, the microstructure evolved from eutectic to hypoeutectic, and the morphologies of the reinforcements present chrysanthemum-shaped, granular and intercrystalline eutectics, respectively. The (Fe,Cr)7C3 particulate bundles reinforced composite has high macrohardness and excellent wear resistance under dry sliding wear testing conditons.

Sign in / Sign up

Export Citation Format

Share Document