Calorimetric measurement of the maximum glass transition temperature in a thermosetting resin

1993 ◽  
Vol 40 (2) ◽  
pp. 553-563 ◽  
Author(s):  
S. Montserrat
Keyword(s):  
Glass Transition ◽  
Transition Temperature ◽  
Glass Transition Temperature ◽  
Thermosetting Resin ◽  
Calorimetric Measurement

A Novel Poly(Ionic Liquid) as the Thermal Insulating Material

2020 ◽  
Vol 13 (3) ◽  
pp. 241-247
Author(s):  
Wenxin Wei ◽  
Guifeng Ma ◽  
Hongtao Wang ◽  
Jun Li
Keyword(s):  
Thermal Conductivity ◽  
Ionic Liquid ◽  
Glass Transition ◽  
Transition Temperature ◽  
Glass Transition Temperature ◽  
Flame Resistance ◽  
Insulating Material ◽  
Low Thermal Conductivity ◽  
Thermal Insulating ◽  
Poly Ionic Liquid

Objective: A new poly(ionic liquid)(PIL), poly(p-vinylbenzyltriphenylphosphine hexafluorophosphate) (P[VBTPP][PF6]), was synthesized by quaternization, anion exchange reaction, and free radical polymerization. Then a series of the PIL were synthesized at different conditions. Methods: The specific heat capacity, glass-transition temperature and melting temperature of the synthesized PILs were measured by differential scanning calorimeter. The thermal conductivities of the PILs were measured by the laser flash analysis method. Results: Results showed that, under optimized synthesis conditions, P[VBTPP][PF6] as the thermal insulator had a high glass-transition temperature of 210.1°C, high melting point of 421.6°C, and a low thermal conductivity of 0.0920 W m-1 K-1 at 40.0°C (it was 0.105 W m-1 K-1 even at 180.0°C). The foamed sample exhibited much low thermal conductivity λ=0.0340 W m-1 K-1 at room temperature, which was comparable to a commercial polyurethane thermal insulating material although the latter had a much lower density. Conclusion: In addition, mixing the P[VBTPP][PF6] sample into polypropylene could obviously increase the Oxygen Index, revealing its efficient flame resistance. Therefore, P[VBTPP][PF6] is a potential thermal insulating material.

High-temperature carbon plastics based on thermoreactive polyimide binder

2020 ◽  
pp. 89-102
Author(s):  
M. I. Valueva ◽  
I. V. Zelenina ◽  
M. A. Zharinov ◽  
M. A. Khaskov
Keyword(s):  
Glass Transition ◽  
High Temperature ◽  
Transition Temperature ◽  
Glass Transition Temperature ◽  
Strength Properties ◽  
High Glass Transition Temperature ◽  
Reinforced Plastics ◽  
Carbon Plastics ◽  
Fundamental Possibility ◽  
Fiber Reinforced Plastics

The article presents results of studies of experimental carbon plastics based on thermosetting PMRpolyimide binder. Сarbon fiber reinforced plastics (CFRPs) are made from prepregs prepared by melt and mortar technologies, so the rheological properties of the polyimide binder were investigated. The heat resistance of carbon plastics was researched and its elastic-strength characteristics were determined at temperatures up to 320°С. The fundamental possibility of manufacturing carbon fiber from prepregs based on polyimide binder, obtained both by melt and mortar technologies, is shown. CFRPs made from two types of prepregs have a high glass transition temperature: 364°C (melt) and 367°C (solution), with this temperature remaining at the 97% level after boiling, and also at approximately the same (86–97%) level of conservation of elastic strength properties at temperature 300°С.

Sign in / Sign up

Export Citation Format

Share Document