Topology and vortex structures of a curving turbine cascade with tip clearance (I)—Experimental model and topological flow patterns on both endwalls and blade surfaces

2002 ◽  
Vol 23 (8) ◽  
pp. 948-957 ◽  
Author(s):  
Yang Qing-hai ◽  
Huang Hong-yan ◽  
Han Wan-jin
Keyword(s):  
Experimental Model ◽  
Flow Patterns ◽  
Vortex Structures ◽  
Tip Clearance ◽  
Turbine Cascade

scholarly journals Numerical Calculation of Flow for Cascade With Tip Clearance

1994 ◽  
Author(s):  
Shimpei Mizuki ◽  
Hoshio Tsujita
Keyword(s):  
Three Dimensional ◽  
Tip Clearance ◽  
Turbine Cascade ◽  
Governing Equations ◽  
Tensor Form ◽  
Pressure Surface ◽  
Rear Part ◽  
Blade Tip ◽  
Flow Through ◽  
Blade Tip Geometry

Three-dimensional incompressible turbulent flow within a linear turbine cascade with tip clearance is analyzed numerically. The governing equations involving the standard k-ε model are solved in the physical component tensor form with a boundary-fitted coordinate system. In the analysis, the blade tip geometry is treated accurately in order to predict the flow through the tip clearance in detail when the blades have large thicknesses. Although the number of grids employed in the present study is not enough because of the limitation of computer storage memory, the computed results show good agreements with the experimental results. Moreover, the results clearly exhibit the locus of minimum pressure on the rear part of the pressure surface at the blade tip.

Effects of Tip Clearance on Aerodynamic Damping in a Linear Turbine Cascade

2008 ◽  
Vol 24 (1) ◽  
pp. 26-33 ◽  
Author(s):  
Xiuquan Huang ◽  
Li He ◽  
David L. Bell
Keyword(s):  
Tip Clearance ◽  
Turbine Cascade ◽  
Aerodynamic Damping

The Measurement and Formation of Tip Clearance Loss

1989 ◽  
Vol 111 (3) ◽  
pp. 257-263 ◽  
Author(s):  
J. P. Bindon
Keyword(s):  
Pressure Gradient ◽  
Secondary Flow ◽  
Separation Bubble ◽  
Tip Clearance ◽  
Turbine Cascade ◽  
High Loss ◽  
Performance Improvements ◽  
Internal Loss ◽  
Internal Gap ◽  
First Time

The detailed development of tip clearance loss from the leading to trailing edge of a linear turbine cascade was measured and the contributions made by mixing, internal gap shear flow, and endwall/ secondary flow were identified, separated, and quantified for the first time. Only 13 percent of the overall loss arises from endwall/secondary flow and of the remaining 87 percent, 48 percent is due to mixing and 39 percent is due to internal gap shear. All loss formation appears to be dominated by phenomena connected with the gap separation bubble. Flow established within the bubble by the pressure gradient separates as the gradient disappears and most of the internal loss is created by the entrainment of this separated fluid. When this high-loss leakage wake enters the mainstream, it separates due to the suction corner pressure gradient to create virtually all the measured mixing loss. It is suggested that the control of tip clearance loss by discharge coefficient reduction actually introduces loss. Performance improvements may result from streamlined tip geometries that optimize the tradeoff between entropy production and flow deflection.

Experimental study on axially non-uniform clearances in a linear turbine cascade with a cavity squealer tip

2018 ◽  
Vol 233 (5) ◽  
pp. 1645-1655
Author(s):  
Shaowen Chen ◽  
Qinghe Meng ◽  
Weihang Li ◽  
Zhihua Zhou ◽  
Songtao Wang
Keyword(s):  
Flow Field ◽  
Buffer Zone ◽  
Aerodynamic Performance ◽  
Field Structure ◽  
Tip Clearance ◽  
Turbine Cascade ◽  
Tip Leakage Flow ◽  
Tip Leakage ◽  
Passage Vortex ◽  
Flow Loss

The effects of axially non-uniform clearances on the tip leakage flow and aerodynamic performance in a linear turbine cascade with a cavity squealer tip were investigated in this study with the objective of improving the flow loss and tip flow field structure. A calibrated five-hole probe was used for the measurement of three-dimensional flows downstream of the cascade. The method of oil-flow visualization was used to show the endwall flow field structure. The distribution of endwall static pressure was measured particularly by using the special moveable endwall. The axially non-uniform clearance, as a novel strategy that has a non-negligible influence on tip clearance flow and clearance leakage loss, may become a potential technology for improving aerodynamic performance in turbine cascades. By using the expanding clearance, the flow loss at the outlet is reduced effectively and an apparent improvement of aerodynamic performance in the turbine cascade is gained. Under the tip clearances of 0.75% H and 2% H, the maximum reduction of overall total pressure loss coefficient at the outlet is separately about 2.3% and 3.5% compared with the uniform clearance. The shrinkage of the buffer zone is considered to be able to weaken the interaction of the tip leakage vortex and passage vortex and thus reduce the loss of passage vortex. For the shrinking clearance, a noticeable decline in the aerodynamic performance of turbine cascade with cavity squealer tip is exhibited at both on and off design conditions in contrast to the uniform clearance. In addition, the effects of axially non-uniform clearances on the aerodynamic performance at off-design conditions have been investigated.

Effects of Reynolds Number and Freestream Turbulence on Turbine Tip Clearance Flow

2005 ◽  
Vol 128 (1) ◽  
pp. 166-177 ◽  
Author(s):  
Takayuki Matsunuma
Keyword(s):  
Reynolds Number ◽  
Turbulence Intensity ◽  
Three Dimensional ◽  
Tip Clearance ◽  
Pressure Probe ◽  
Turbine Cascade ◽  
Freestream Turbulence ◽  
Tip Leakage Flow ◽  
Three Dimensional Flow ◽  
Dimensional Flow

Tip clearance losses represent a major efficiency penalty of turbine blades. This paper describes the effect of tip clearance on the aerodynamic characteristics of an unshrouded axial-flow turbine cascade under very low Reynolds number conditions. The Reynolds number based on the true chord length and exit velocity of the turbine cascade was varied from 4.4×104 to 26.6×104 by changing the velocity of fluid flow. The freestream turbulence intensity was varied between 0.5% and 4.1% by modifying turbulence generation sheet settings. Three-dimensional flow fields at the exit of the turbine cascade were measured both with and without tip clearance using a five-hole pressure probe. Tip leakage flow generated a large high total pressure loss region. Variations in the Reynolds number and freestream turbulence intensity changed the distributions of three-dimensional flow, but had no effect on the mass-averaged tip clearance loss of the turbine cascade.

scholarly journals Influences of Tip Cooling Injection on Tip Clearance Control at Design and Off-Design Incidences

2009 ◽  
Vol 2009 ◽  
pp. 1-12 ◽  
Author(s):  
Maosheng Niu ◽  
Shusheng Zang
Keyword(s):  
Heat Transfer ◽  
Tip Clearance ◽  
Air Injection ◽  
Turbine Cascade ◽  
Tip Clearance Flow ◽  
Clearance Flow ◽  
Blade Tip ◽  
Design Value ◽  
Tip Injection ◽  
Clearance Control

A numerical investigation has been performed to study the influences of cooling injection from the blade tip surface on controlling tip clearance flow in an unshrouded, high-turning axial turbine cascade. Emphasis is put on the analysis of the effectiveness of tip injection when the approaching flow is at design and off-design incidences. A total of three incidence angles are investigated, 7.4°, 0°, 0°, 0°, and 7.6°, 0° relative to the design value. The results indicate that even at the off-design incidences, tip injection can also act as an obstruction to the tip clearance flow and weaken the interaction between the passage flow and the tip clearance flow. It is also found that tip injection causes the tip clearance loss to be less sensitive to the incidences. Moreover, with injection, at all these incidences the heat transfer conditions are improved significantly on the blade tip surface in the middle and aft parts of blade. Thus, tip injection is proved to be an effective method of controlling tip clearance flow, even at off-design conditions. Beside that, an indirect empirical correlation is observed to be able to perform well in predicting the losses induced by tip clearance flow at design and off-design conditions, no matter whether air injection is active or not.

Effects of Reynolds Number and Free-Stream Turbulence on Turbine Tip Clearance Flow

2005 ◽  
Author(s):  
Takayuki Matsunuma
Keyword(s):  
Reynolds Number ◽  
Turbulence Intensity ◽  
Free Stream ◽  
Three Dimensional ◽  
Tip Clearance ◽  
Turbine Cascade ◽  
Tip Leakage Flow ◽  
Three Dimensional Flow ◽  
Free Stream Turbulence ◽  
Dimensional Flow

Tip clearance losses represent a major efficiency penalty of turbine blades. This paper describes the effect of tip clearance on the aerodynamic characteristics of an unshrouded axial-flow turbine cascade under very low Reynolds number conditions. The Reynolds number based on the true chord length and exit velocity of the turbine cascade was varied from 4.4 × 104 to 26.6 × 104 by changing the velocity of fluid flow. The free-stream turbulence intensity was varied between 0.5% and 4.1% by modifying turbulence generation sheet settings. Three-dimensional flow fields at the exit of the turbine cascade were measured both with and without tip clearance using a five-hole pressure probe. Tip leakage flow generated a large high total pressure loss region. Variations in the Reynolds number and free-stream turbulence intensity changed the distributions of three-dimensional flow, but had no effect on the mass-averaged tip clearance loss of the turbine cascade.

Sign in / Sign up

Export Citation Format

Share Document