Effect of electron irradiation on creep and dislocation structure of aluminium

1979 ◽  
Vol 29 (11) ◽  
pp. 1260-1265
Author(s):  
L. I. Ivanov ◽  
A. Orlová ◽  
V. M. Lazorenko ◽  
O. V. Martishin
Keyword(s):  
Dislocation Structure ◽  
Electron Irradiation

Evaluation of single-electron movies of glutamine synthetase molecules

1983 ◽  
Vol 41 ◽  
pp. 280-281
Author(s):  
W. Kunath ◽  
E. Zeitler ◽  
M. Kessel
Keyword(s):  
Electron Microscope ◽  
Glutamine Synthetase ◽  
Electron Irradiation ◽  
Structural Damage ◽  
Structural Changes ◽  
Single Electron ◽  
Continuous Series ◽  
Digital Recording ◽  
Recording Device ◽  
Low Exposure

The features of digital recording of a continuous series (movie) of singleelectron TV frames are reported. The technique is used to investigate structural changes in negatively stained glutamine synthetase molecules (GS) during electron irradiation and, as an ultimate goal, to look for the molecules' “undamaged” structure, say, after a 1 e/Å2 dose.The TV frame of fig. la shows an image of 5 glutamine synthetase molecules exposed to 1/150 e/Å2. Every single electron is recorded as a unit signal in a 256 ×256 field. The extremely low exposure of a single TV frame as dictated by the single-electron recording device including the electron microscope requires accumulation of 150 TV frames into one frame (fig. lb) thus achieving a reasonable compromise between the conflicting aspects of exposure time per frame of 3 sec. vs. object drift of less than 1 Å, and exposure per frame of 1 e/Å2 vs. rate of structural damage.

The dislocation structure of a 10° [110] tilt boundary in silicon

1983 ◽  
Vol 41 ◽  
pp. 114-115
Author(s):  
B. Cunningham ◽  
D.G. Ast
Keyword(s):  
Dislocation Structure ◽  
Tilt Angle ◽  
Imaging Technique ◽  
Diamond Lattice ◽  
Tilt Boundary ◽  
Formation Mechanisms ◽  
Diffraction Contrast ◽  
Lattice Fringe ◽  
Tilt Boundaries ◽  
Chemically Vapor Deposited

There have Been a number of studies of low-angle, θ < 4°, [10] tilt boundaries in the diamond lattice. Dislocations with Burgers vectors a/2<110>, a/2<112>, a<111> and a<001> have been reported in melt-grown bicrystals of germanium, and dislocations with Burgers vectors a<001> and a/2<112> have been reported in hot-pressed bicrystals of silicon. Most of the dislocations were found to be dissociated, the dissociation widths being dependent on the tilt angle. Possible dissociation schemes and formation mechanisms for the a<001> and a<111> dislocations from the interaction of lattice dislocations have recently been given.The present study reports on the dislocation structure of a 10° [10] tilt boundary in chemically vapor deposited silicon. The dislocations in the boundary were spaced about 1-3nm apart, making them difficult to resolve by conventional diffraction contrast techniques. The dislocation structure was therefore studied by the lattice-fringe imaging technique.

Radiation-Induced Precipitation at Thin Foil Surfaces in Ni-Be Alloys

1982 ◽  
Vol 40 ◽  
pp. 598-599
Author(s):  
T. Mukai ◽  
T. E. Mitchell
Keyword(s):  
Electron Microscopy ◽  
High Voltage ◽  
Electron Irradiation ◽  
High Vacuum ◽  
Thin Foil ◽  
Homogeneous Precipitation ◽  
High Voltage Electron Microscopy ◽  
Voltage Electron ◽  
High Voltage Electron ◽  
Radiation Induced

Radiation-induced homogeneous precipitation in Ni-Be alloys was recently observed by high voltage electron microscopy. A coupling of interstitial flux with solute Be atoms is responsible for the precipitation. The present investigation further shows that precipitation is also induced at thin foil surfaces by electron irradiation under a high vacuum.

Void-Lattice Formation in Natural Fluorite by Electron Irradiation

1976 ◽  
Vol 34 ◽  
pp. 614-615 ◽  
Author(s):  
L.E. Murr
Keyword(s):  
Electron Microscope ◽  
Electron Irradiation ◽  
Heavy Ion ◽  
High Energy ◽  
Stoichiometric Ratio ◽  
Direct Observations ◽  
Transmission Electron ◽  
Anion Vacancies ◽  
Cation And Anion Vacancies ◽  
Lattice Formation

The production of void lattices in metals as a result of displacement damage associated with high energy and heavy ion bombardment is now well documented. More recently, Murr has shown that a void lattice can be developed in natural (colored) fluorites observed in the transmission electron microscope. These were the first observations of a void lattice in an irradiated nonmetal, and the first, direct observations of color-center aggregates. Clinard, et al. have also recently observed a void lattice (described as a high density of aligned "pores") in neutron irradiated Al2O3 and Y2O3. In this latter work, itwas pointed out that in order that a cavity be formed,a near-stoichiometric ratio of cation and anion vacancies must aggregate. It was reasoned that two other alternatives to explain the pores were cation metal colloids and highpressure anion gas bubbles.Evans has proposed that void lattices result from the presence of a pre-existing impurity lattice, and predicted that the formation of a void lattice should restrict swelling in irradiated materials because it represents a state of saturation.

Mechanical Properties and Dislocation Structure of Single Crystal Cdte Deformed in Compression at 300°C

1976 ◽  
Vol 34 ◽  
pp. 592-593
Author(s):  
Ernest L. Hall ◽  
J. B. Vander Sande
Keyword(s):  
Mechanical Properties ◽  
Single Crystal ◽  
Dislocation Structure ◽  
Room Temperature ◽  
Elevated Temperatures ◽  
Strain Curve ◽  
Optical Devices ◽  
Semiconductor Compound ◽  
Wide Range ◽  
Sample Orientation

The present paper describes research on the mechanical properties and related dislocation structure of CdTe, a II-VI semiconductor compound with a wide range of uses in electrical and optical devices. At room temperature CdTe exhibits little plasticity and at the same time relatively low strength and hardness. The mechanical behavior of CdTe was examined at elevated temperatures with the goal of understanding plastic flow in this material and eventually improving the room temperature properties. Several samples of single crystal CdTe of identical size and crystallographic orientation were deformed in compression at 300°C to various levels of total strain. A resolved shear stress vs. compressive glide strain curve (Figure la) was derived from the results of the tests and the knowledge of the sample orientation.

HREM Study of electron-induced surface radiation damage in ReO3

1991 ◽  
Vol 49 ◽  
pp. 636-637
Author(s):  
R. Ai ◽  
H.-J. Fan ◽  
L. D. Marks
Keyword(s):  
Transition Metal ◽  
Metal Ions ◽  
Metal Oxides ◽  
Electron Irradiation ◽  
Transition Metal Oxides ◽  
Carbon Film ◽  
Transition Metal Ions ◽  
Surface Radiation ◽  
Valence Transition ◽  
Electron Microscopes

It has been known for a long time that electron irradiation induces damage in maximal valence transition metal oxides such as TiO2, V2O5, and WO3, of which transition metal ions have an empty d-shell. This type of damage is excited by electronic transition and can be explained by the Knoteck-Feibelman mechanism (K-F mechanism). Although the K-F mechanism predicts that no damage should occur in transition metal oxides of which the transition metal ions have a partially filled d-shell, namely submaximal valence transition metal oxides, our recent study on ReO3 shows that submaximal valence transition metal oxides undergo damage during electron irradiation.ReO3 has a nearly cubic structure and contains a single unit in its cell: a = 3.73 Å, and α = 89°34'. TEM specimens were prepared by depositing dry powders onto a holey carbon film supported on a copper grid. Specimens were examined in Hitachi H-9000 and UHV H-9000 electron microscopes both operated at 300 keV accelerating voltage. The electron beam flux was maintained at about 10 A/cm2 during the observation.

Observations of dislocation interactions with recrystallized grain boundaries

1988 ◽  
Vol 46 ◽  
pp. 628-629
Author(s):  
C. W. Price
Keyword(s):  
Dislocation Density ◽  
Grain Boundary ◽  
Strain Rate ◽  
Grain Boundaries ◽  
Dislocation Structure ◽  
Hot Deformation ◽  
Static Recrystallization ◽  
High Dislocation Density ◽  
High Angle ◽  
Dislocation Interactions

Little evidence exists on the interaction of individual dislocations with recrystallized grain boundaries, primarily because of the severely overlapping contrast of the high dislocation density usually present during recrystallization. Interesting evidence of such interaction, Fig. 1, was discovered during examination of some old work on the hot deformation of Al-4.64 Cu. The specimen was deformed in a programmable thermomechanical instrument at 527 C and a strain rate of 25 cm/cm/s to a strain of 0.7. Static recrystallization occurred during a post anneal of 23 s also at 527 C. The figure shows evidence of dissociation of a subboundary at an intersection with a recrystallized high-angle grain boundary. At least one set of dislocations appears to be out of contrast in Fig. 1, and a grainboundary precipitate also is visible. Unfortunately, only subgrain sizes were of interest at the time the micrograph was recorded, and no attempt was made to analyze the dislocation structure.

Bright field and weak-beam images of dislocations gliding on (001) planes in F.C.C. metals

1978 ◽  
Vol 36 (1) ◽  
pp. 352-353
Author(s):  
H. P. Karnthaler ◽  
A. Korner
Keyword(s):  
Single Crystals ◽  
Dislocation Structure ◽  
Room Temperature ◽  
Stage Ii ◽  
Bright Field ◽  
Weak Beam ◽  
Standard Orientation

In f.c.c. metals slip is observed to occur generally on {111} planes. Glide dislocations on intersecting {111} planes can react with each other and form Lomer-Cottrell locks which lie along a <110> direction and are sessile since they are split on two {111} planes. Cottrell already pointed out that these dislocations could glide on {001} planes if they were not split. The first study of this phenomenon has been published recently. It is the purpose of this paper to report some interesting new details of the dislocations gliding on {001} planes in pure Ni, Cu, and Ag deformed at room temperature.Single crystals are grown with standard orientation and strained into stage II. The crystals are sliced parallel to the (001) planes. The dislocation structure is studied by TEM and the Burgers vectors ḇ and glide planes of the dislocations are determined unambiguously.In Fig.l primary P and secondary S dislocations react and form composite dislocations K.

Ordering in Ni4Mo by TEM and APFIM

1987 ◽  
Vol 45 ◽  
pp. 214-215
Author(s):  
E.A. Kenik ◽  
T.A. Zagula ◽  
M.K. Miller ◽  
J. Bentley
Keyword(s):  
Electron Irradiation ◽  
Low Temperatures ◽  
Short Range ◽  
Atom Probe ◽  
Range Order ◽  
Considerable Time ◽  
Probe Field ◽  
Disordered Phase ◽  
Transmission Electron ◽  
Diffraction Patterns

The state of long-range order (LRO) and short-range order (SRO) in Ni4Mo has been a topic of interest for a considerable time (see Brooks et al.). The SRO is often referred to as 1½0 order from the apparent position of the diffuse maxima in diffraction patterns, which differs from the positions of the LRO (D1a) structure. Various studies have shown that a fully disordered state cannot be retained by quenching, as the atomic arrangements responsible for the 1½0 maxima are present at temperatures above the critical ordering temperature for LRO. Over 20 studies have attempted to identify the atomic arrangements associated with this state of order. A variety of models have been proposed, but no consensus has been reached. It has also been shown that 1 MeV electron irradiation at low temperatures (∼100 K) can produce the disordered phase in Ni4Mo. Transmission electron microscopy (TEM), atom probe field ion microscopy (APFIM), and electron irradiation disordering have been applied in the current study to further the understanding of the ordering processes in Ni4Mo.

The butterfly martensite nucleation in an iron and nickel alloy

1990 ◽  
Vol 48 (4) ◽  
pp. 906-907
Author(s):  
Q.Z. Chen ◽  
X.F. Wu ◽  
T. Ko
Keyword(s):  
Nickel Alloy ◽  
Ethyl Alcohol ◽  
Dislocation Structure ◽  
Martensite Transformation ◽  
Room Temperature ◽  
The Matrix

Some butterfly martensite nuclei were observed in an Fe-27.6Ni-0.89V-0.05C alloy. The alloy was austenitized at 1200°C for 1 hour. Some samples were aged at 850° C for 40 minutes and quenched in 10% brine at room temperature. All the samples were cooled in ethyl alcohol for martensite transformation.A nucleus in an unaged specimen is shown in Fig.1. The nucleus has certain contrast different from the matrix and is shaped like one wing of a butter fly martensite. The SADP of the circled region is measured to be: da=dh, and approximate to dγ(111) and dm(110) with ∠AOB = 55° . It is similar to [011]f.c.c and b patterns in the anglez ∠AOB and the ratio ra/rb, respectively. The SADP shows that the structure of the nucleus is between f.c.c and b.c.c. The dislocation structure within the nucleus is shown in Fig.2. Their Burgers vectors and line directions are also given in it. There are many long dislocations near it without dislocations piled up as shown in Fig.3.Long dislocations are closed at one end as an envelope.

Sign in / Sign up

Export Citation Format

Share Document