A new approach to the determination of methane content of coal seams

1987 ◽  
Vol 5 (4) ◽  
pp. 369-376 ◽  
Author(s):  
Bangsi Dhar Banerjee
Energies ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 982
Author(s):  
Nikodem Szlązak ◽  
Dariusz Obracaj ◽  
Marek Korzec

The determination of natural gas content in coal seams is essential to safe mining activities and to estimate gas resources. It is used to estimate methane emissions into workings, which is very important when using preventive measures of methane ignition and explosion. Methane content in a coal seam is mostly determined using a direct method. However, a problem with estimation of gas loss during collecting a sample in a mine occurs in each method. That gas loss is estimated using different procedures. In the Polish mining industry, methane content in a coal seam is mostly determined during roadway advancing faces in coal seams. The differences in procedures for determining methane content in coal in various laboratories gave rise to starting research into developing a new method. This article presents results of study of gas loss unification for the determination of methane content in coal seams. The research focused mainly on determining a uniform method for estimating gas loss using the early adsorption diffusion process. The method of coal sample saturation with methane was used to measure gas desorption rate. Saturation pressures of samples were determined for coal seams in the Upper-Silesian Coal Basin. The analysis of desorption results allowed to determine the dependence between methane content in a coal sample and the initial methane content in a coal seam. It was concluded that the desorption rate was highest within two minutes. For the procedure of coal sampling, gas loss was determined at 12% of both desorbed and residual gases. The presented research results gave rise to developing a uniform method for determining gas content used in Polish coal mining. The method was accepted as the national standard. Methodology using a new gas loss estimation procedure allows for achieving relatively fast results of the determination of methane content in coal seams, which is very important, especially in gassy mines.


Author(s):  
E.V. Fedorov ◽  
◽  
S.B. Kulibaba ◽  
A.A. Meshkov ◽  
◽  
...  

S.M. Kirov mine of JSC SUEK-Kuzbass develops Boldyrevsky and Polenovsky seams and is classified as a super-category for methane. Under these conditions, the development of seams requires a set of measures for their degassing. Methods and parameters for degassing the main sources of methane release in the coal mines are selected considering the faces gas content. It is calculated based on the natural methane content of the coal seams and host rocks determined at the stage of geologic exploration activity. The aim of the work conducted by the authors is to establish the actual distribution of natural methane seam Boldyrevsky based on the analysis of research results of the coal-gas samples and experimental evaluation of the residual gas content in the mine workings. Natural gas content of the mine field of S.M. Kirov JSC SUEK-Kuzbass mine was determined based on the analysis of 538 coal-gas samples on 30 seams. All the coal and gas samples taken from Boldyrevsky seam were analyzed. Distribution of the actual values of natural methane content from the hypsometric depths of the seam was plotted. Distribution was plotted concerning the actual values of natural methane from hypsometric depths of the formation. The obtained data were compared with the results of experimental determination of the residual gas content of Boldyrevsky seam from the mine workings. Based on the results obtained, CH4 isogases were constructed based on the actual and maximum values of the natural methane content in Boldyrevsky seam. It is established that the natural methane content of Boldyrevsky seam, that was determined at the stage of geological exploration for the entire field of S.V. Kirov mine, has overestimated values — by 35–40 % compared to the actual data, and by 25–30% in relation to the maximum actual data.


Energies ◽  
2021 ◽  
Vol 15 (1) ◽  
pp. 178
Author(s):  
Nikodem Szlązak ◽  
Marek Korzec ◽  
Kazimierz Piergies

The determination of methane content of coal seams is conducted in hard coal mines in order to assess the state of methane hazard but also to evaluate gas resources in the deposit. In the world’s mining industry, natural gas content in coal determination is usually based on direct methods. It remains the basic method in Poland as well. An important element in the determination procedure is the gas loss that occurs while collecting a sample for testing in underground conditions. In the method developed by the authors, which is a Polish standard, based on taking a sample in the form of drill cuttings, this loss was established at a level of 12%. Among researchers dealing with the methane content of coal, there are doubts related to the procedures adopted for coal sampling and the time which passes from taking a sample to enclosing it in a sealed container. Therefore, the studies were designed to evaluate the degree of degassing of the sample taken in the form of drill cuttings according to the standard procedure and in the form of the drill core from a coal mine roadway. The results show that the determinations made for the core coincide with the determinations made for the drill cutting samples, with the loss of gas taken into account.


2017 ◽  
Vol 30 (1) ◽  
pp. 273-289
Author(s):  
Anmari Meerkotter

The Constitutional Court (CC) judgment of Lee v Minister of Correction Services 2013 2SA 144 (CC) is a recent contribution to transformative constitutional jurisprudence in the field of the law of delict. This matter turned on the issue of factual causation in the context of wrongful and negligent systemic omissions by the state. In this case note, I explore the law relating to this element of delictual liability with specific regard to the traditional test for factual causation – the conditio sine qua non (‘but-for’) test. In particular, I note the problems occasioned by formalistic adherence to this test in the context of systemic state omissions as evidenced by the SCA judgment in the same matter. I also consider the manner in which English courts have addressed this problem. Thereafter, I analyse the CC’s broader approach to the determination of factual causation as one based on common sense and justice. I argue that this approach endorses a break from a formalistic application of the test and constitutes a step towards an approach which resonates with the foundational constitutional values of freedom, dignity and equality. Furthermore, it presents an appropriate solution to the problems associated with factual causation where systemic omissions are concerned. I then consider the transformative impact of the Lee judgment. In particular, I argue that the broader enquiry favoured by the CC facilitates the realisation of constitutionally guaranteed state accountability, and amounts to an extension of the existing norm of accountability jurisprudence. Hence, I contend that the judgment presents a further effort by the Constitutional Court to effect wholesale the constitutionalisation of the law of delict, as well as a vindicatory tool to be used by litigants who have been adversely affected by systemic state omissions.


Author(s):  
Romain Desplats ◽  
Timothee Dargnies ◽  
Jean-Christophe Courrege ◽  
Philippe Perdu ◽  
Jean-Louis Noullet

Abstract Focused Ion Beam (FIB) tools are widely used for Integrated Circuit (IC) debug and repair. With the increasing density of recent semiconductor devices, FIB operations are increasingly challenged, requiring access through 4 or more metal layers to reach a metal line of interest. In some cases, accessibility from the front side, through these metal layers, is so limited that backside FIB operations appear to be the most appropriate approach. The questions to be resolved before starting frontside or backside FIB operations on a device are: 1. Is it do-able, are the metal lines accessible? 2. What is the optimal positioning (e.g. accessing a metal 2 line is much faster and easier than digging down to a metal 6 line)? (for the backside) 3. What risk, time and cost are involved in FIB operations? In this paper, we will present a new approach, which allows the FIB user or designer to calculate the optimal FIB operation for debug and IC repair. It automatically selects the fastest and easiest milling and deposition FIB operations.


Sensors ◽  
2021 ◽  
Vol 21 (9) ◽  
pp. 3070
Author(s):  
Sebastian Iwaszenko ◽  
Jakub Munk ◽  
Stefan Baron ◽  
Adam Smoliński

Modern dentistry commonly uses a variety of imaging methods to support diagnosis and treatment. Among them, cone beam computed tomography (CBCT) is particularly useful in presenting head structures, such as the temporomandibular joint (TMJ). The determination of the morphology of the joint is an important part of the diagnosis as well as the monitoring of the treatment results. It can be accomplished by measurement of the TMJ gap width at three selected places, taken at a specific cross-section. This study presents a new approach to these measurements. First, the CBCT images are denoised using curvilinear methods, and the volume of interest is determined. Then, the orientation of the vertical cross-section plane is computed based on segmented axial sections of the TMJ head. Finally, the cross-section plane is used to determine the standardized locations, at which the width of the gap between condyle and fossa is measured. The elaborated method was tested on selected TMJ CBCT scans with satisfactory results. The proposed solution lays the basis for the development of an autonomous method of TMJ index identification.


Sign in / Sign up

Export Citation Format

Share Document