Relationship between yield stress in compression and mechanical properties of steel, copper, aluminum and their alloys

1972 ◽  
Vol 4 (6) ◽  
pp. 708-715 ◽  
Author(s):  
V. A. Krokha
Keyword(s):  
Mechanical Properties ◽  
Yield Stress ◽  
Copper Aluminum

Mechanichal Properties of DGEBA/TEPA Modified Epoxy Resin

2014 ◽  
Vol 775-776 ◽  
pp. 588-592
Author(s):  
Camila Rodrigues Amaral ◽  
Ruben Jesus Sanchez Rodriguez ◽  
Magno Luiz Tavares Bessa ◽  
Verônica Scarpini Cândido ◽  
Sergio Neves Monteiro
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Epoxy Resin ◽  
Yield Stress ◽  
Diglycidyl Ether ◽  
Notch Toughness ◽  
Epoxy Network ◽  
Structural Network ◽  
Flexural Tests ◽  
Modified Epoxy

The correlation between the structural network of a diglycidyl ether of the bisphenol-A (DGEBA) epoxy resin, modified by two distinct aliphatic amines (tetraethylenepentamine TEPA and jeffamine D230), and its mechanical properties, was investigated as possible matrix for abrasive composites applications. Both flexural tests, to determine the yield stress and the elastic modulus, as well as impact tests to determine the notch toughness, were performed. The DGEBA/D230 presented the highest stiffness and toughness but lowest yield stress. This epoxy network also displayed a greater plastic deformation during fracture.

INVESTIGATING THE INFLUENCE OF ENVIRONMENTAL CONDITIONING ON EPOXY RESINS AT QUASISTATIC AND HIGH STRAIN RATES FOR MATERIAL OPERATING LIMIT

2021 ◽  
Author(s):  
SAGAR M. DOSHI, SAGAR M. DOSHI, ◽  
NITHINKUMAR MANOHARAN ◽  
BAZLE Z. (GAMA) HAQUE, ◽  
JOSEPH DEITZEL ◽  
JOHN W. GILLESPIE, JR.
Keyword(s):  
Mechanical Properties ◽  
Epoxy Resin ◽  
Yield Stress ◽  
High Strain ◽  
Operating Conditions ◽  
Strain Rates ◽  
High Strain Rates ◽  
Stress Strain ◽  
Wide Range ◽  
Environmental Aging

Epoxy resin-based composite panels used for armors may be subjected to a wide range of operating temperatures (-55°C to 76°C) and high strain rates on the order of 103-104 s-1. Over the life cycle, various environmental factors also affect the resin properties and hence influence the performance of the composites. Therefore, it is critical to determine the stress-strain behavior of the epoxy resin over a wide range of strain rates and temperatures for accurate multi-scale modeling of composites and to investigate the influence of environmental aging on the resin properties. Additionally, the characterization of key mechanical properties such as yield stress, modulus, and energy absorption (i.e. area under the stress-strain curve) at varying temperatures and moisture can provide critical data to calculate the material operating limits. In this study, we characterize mechanical properties of neat epoxy resin, SC-15 (currently used in structural armor) and RDL-RDC using uniaxial compression testing. RDL-RDC, developed by Huntsman Corporation, has a glass transition temperature of ~ 120°C, compared to ~ 85°C of SC-15. A split Hopkinson pressure bar is used for high strain rate testing. Quasistatic testing is conducted using a screw-driven testing machine (Instron 4484) at 10-3 s-1 and 10-1 s-1 strain rates and varying temperatures. The yield stress is fit to a modified Eyring model over the varying strain rates at room temperature. For rapid investigation of resistance to environmental aging, accelerated aging tests are conducted by immersing the specimens in 100°C water for 48 hours. Specimens are conditioned in an environmental chamber at 76 °C and 88% RH until they reach equilibrium. Tests are then conducted at five different temperatures from 0°C to 95°C, and key mechanical properties are then plotted vs. temperature. The results presented are an important step towards developing a methodology to identify environmental operating conditions for composite ground vehicle applications.

Mechanical Properties of Electroplated Copper Thin Films

1999 ◽  
Vol 594 ◽  
Author(s):  
R. Spolenak ◽  
C. A. Volkert ◽  
K. Takahashi ◽  
S. Fiorillo ◽  
J. Miner ◽  
...  
Keyword(s):  
Thin Films ◽  
Mechanical Properties ◽  
Grain Size ◽  
Film Thickness ◽  
Yield Stress ◽  
Laser Scanning ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Cu Films ◽  
Electroplated Copper

AbstractIt is well known that the mechanical properties of thin films depend critically on film thickness However, the contributions from film thickness and grain size are difficult to separate, because they typically scale with each other. In one study by Venkatraman and Bravman, Al films, which were thinned using anodic oxidation to reduce film thickness without changing grain size, showed a clear increase in yield stress with decreasing film thickness.We have performed a similar study on both electroplated and sputtered Cu films by using chemical-mechanical polishing (CMP) to reduce the film thickness without changing the grain size. Stress-temperature curves were measured for both the electroplated and sputtered Cu films with thicknesses between 0.1 and 1.8 microns using a laser scanning wafer curvature technique. The yield stress at room temperature was found to increase with decreasing film thickness for both sets of samples. The sputtered films, however, showed higher yield stresses in comparison to the electroplated films. Most of these differences can be attributed to the different microstructures of the films, which were determined by focused ion beam (FIB) microscopy and x-ray diffraction.

scholarly journals Hardening of Nickel Alloys by Ion Implantation of Titanium and Carbon

1996 ◽  
Vol 444 ◽  
Author(s):  
S. M. Myers ◽  
D. M. Follstaedt ◽  
J. A. Knapp ◽  
T. R. Christenson
Keyword(s):  
Mechanical Properties ◽  
Finite Element ◽  
Surface Layer ◽  
Ion Implantation ◽  
Finite Element Modeling ◽  
Yield Stress ◽  
Nickel Alloys ◽  
Element Modeling ◽  
Order Of Magnitude ◽  
Amorphous Surface

AbstractDual ion implantation of titanium and carbon was shown to produce an amorphous surface layer in annealed bulk nickel, in electroformed Ni, and in electroformed Ni7 5Fe 2 5. Diamond-tip nanoindentation coupled with finite-element modeling quantified the elastic and plastic mechanical properties of the implanted region. The amorphized matrix, with a thickness of about 100 nm, has a yield stress of approximately 6 GP and an intrinsic hardness near 16 GPa, exceeding by an order of magnitude the corresponding values for annealed bulk Ni. Implications for micro-electromechanical systems are discussed.

Effects of a pre-anneal on the mechanical properties of γ-TiAl

2000 ◽  
Vol 646 ◽  
Author(s):  
Fabienne Grégori ◽  
Philippe Penhoud ◽  
Patrick Veyssière
Keyword(s):  
Mechanical Properties ◽  
Yield Stress ◽  
Alloy Composition ◽  
Heat Treatments ◽  
Tial Alloys ◽  
Clear Effect ◽  
Interstitial Atoms

ABSTRACTThe temperature, TP, and the stress, σP, at which the yield stress of γ-TiAl alloys peaks are influenced by factors such as alloy composition and load orientation. Available data indicates that in the absence of adequate heat treatments, TP and σP are shifted towards values significantly higher than those of samples pre-annealed in order to precipitate interstitial atoms. Conditions under which precipitation influences the anomalous regime are revealed by dedicated tests. In addition to pointing out the clear effect of interstitials, these tests suggest that further ordering may contribute to the strength of Al-rich γ-TiAl.

scholarly journals Evaluating Mechanical Properties of Thin Layers using Nanoindentation and Finite-Element Modeling: Implanted Metals and Deposited Layers

1996 ◽  
Vol 438 ◽  
Author(s):  
J. A. Knapp ◽  
D. M. Follstaedt ◽  
J. C. Barbour ◽  
S. M. Myers ◽  
J. W. Ager ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Finite Element ◽  
Finite Element Modeling ◽  
Yield Stress ◽  
Young’S Modulus ◽  
Layer Thickness ◽  
Young's Modulus ◽  
Thin Layers ◽  
Element Modeling ◽  
Surface Modified

AbstractWe present a methodology based on finite-element modeling of nanoindentation data to extract reliable and accurate mechanical properties from thin, hard films and surface-modified layers on softer substrates. The method deduces the yield stress, Young's modulus, and hardness from indentations as deep as 50% of the layer thickness.

Biomimetic composites inspired by venous leaf

2017 ◽  
Vol 52 (3) ◽  
pp. 361-372 ◽  
Author(s):  
Gongdai Liu ◽  
R Ghosh ◽  
A Vaziri ◽  
A Hossieni ◽  
D Mousanezhad ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Yield Stress ◽  
Poisson’S Ratio ◽  
Composite Structures ◽  
Volume Fraction ◽  
Matrix Material ◽  
Poisson's Ratio ◽  
Fiber Volume ◽  
Young’S Moduli

A typical plant leaf can be idealized as a composite having three principal fibers: the central mid-fiber corresponding to the mid-rib, straight parallel secondary fibers attached to the mid-fiber representing the secondary veins, and then another set of parallel fibers emanating from the secondary fibers mimicking the tertiary fibers embedded in a matrix material. This paper introduces a biomimetic composite design inspired by the morphology of venous leafs and investigates the effects of venation morphologies on the in-plane mechanical properties of the biomimetic composites using finite element method. The mechanical properties such as Young’s moduli, Poisson’s ratio, and yield stress under uniaxial loading of the resultant composite structures was studied and the effect of different fiber architectures on these properties was investigated. To this end, two broad types of architectures were used both having similar central main fiber but differing in either having only secondary fibers or additional tertiary fibers. The fiber and matrix volume fractions were kept constant and a comparative parametric study was carried out by varying the inclination of the secondary fibers. The results show that the elastic modulus of composite in the direction of main fiber increases linearly with increasing the angle of the secondary fibers. Furthermore, the elastic modulus is enhanced if the secondary fibers are closed, which mimics composites with closed cellular fibers. In contrast, the elastic modulus of composites normal to the main fiber ( x direction) exponentially decreases with the increase of the angle of the secondary fibers and it is little affected by having secondary fibers closed. Similar results were obtained for the yield stress of the composites. The results also indicate that Poisson’s ratio linearly increases with the secondary fiber angle. The results also show that for a constant fiber volume fraction, addition of various tertiary fibers may not significantly enhance the mechanical properties of the composites. The mechanical properties of the composites are mainly dominated by the secondary fibers. Finally, a simple model was proposed to predict these behaviors.

Effects of cross-sessional area and aspect ratio coupled with orientation on mechanical properties and deformation behavior of Cu nanowires

2021 ◽  
Author(s):  
Hui Cao ◽  
Wenke Chen ◽  
Zhiyuan Rui ◽  
Changfeng Yan
Keyword(s):  
Mechanical Properties ◽  
Aspect Ratio ◽  
Yield Stress ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Cross Sectional Area ◽  
Sectional Area ◽  
Cross Sectional ◽  
Cu Nanowires ◽  
The Cross

Abstract Metal nanomaterials exhibit excellent mechanical properties compared with corresponding bulk materials and have potential applications in various areas. Despite a number of studies of the size effect on Cu nanowires mechanical properties with square cross-sectional, investigations of them in rectangular cross-sectional with various sizes at constant volume are rare, and lack of multifactor coupling effect on mechanical properties and quantitative investigation. In this work, the dependence of mechanical properties and deformation mechanisms of Cu nanowires/nanoplates under tension on cross-sessional area, aspect ratio of cross-sectional coupled with orientation were investigated using molecular dynamics simulations and the semi-empirical expressions related to mechanical properties were proposed. The simulation results show that the Young’s modulus and the yield stress sharply increase with the aspect ratio except for the <110>{110}{001} Cu nanowires/nanoplates at the same cross-sectional area. And the Young’s modulus increases while the yield stress decreases with the cross-sectional area of Cu nanowires. However, both of them increase with the cross-sectional area of Cu nanoplates. Besides, the Young’s modulus increases with the cross-sectional area at all the orientations. The yield stress shows a mildly downward trend except for the <111> Cu nanowires with increased cross-sectional area. For the Cu nanowires with a small cross-sectional area, the surface force increases with the aspect ratio. In contrast, it decreases with the aspect ratio increase at a large cross-sectional area. At the cross-sectional area of 13.068 nm2, the surface force decreases with the aspect ratio of the <110> Cu nanowires while it increases at other orientations. The surface force is a linearly decreasing function of the cross-sectional area at different orientations. Quantitative studies show that Young’s modulus and yield stress to the aspect ratio of the Cu nanowires satisfy exponent relationship. In addition, the main deformation mechanism of Cu nanowires is the nucleation and propagation of partial dislocations while it is the twinning-dominated reorientation for Cu nanoplates.

Effect of Thermomechanical Processing on Grain Size, Texture and Mechanical Properties of Pure Magnesium

2020 ◽  
Vol 985 ◽  
pp. 97-108
Author(s):  
Mouhamadou Moustapha Sarr ◽  
Motohiro Yuasa ◽  
Hiroyuki Miyamoto
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Yield Stress ◽  
Thermomechanical Processing ◽  
Pure Magnesium ◽  
Grain Structure ◽  
Misorientation Distribution ◽  
Processed Material ◽  
Texture Characterization

This study aims to investigate the effect of processing routes (A and Bc) and temperature on microstructure, texture and mechanical properties of pure magnesium was studied in this research. An extruded pure magnesium (~99,9 %) was subjected to severe plastic deformation (SPD) by ECAP. Deformation was conducted at 523K and 473K and two different processing routes (A and Bc) were used to control the texture. The microstructure and texture characterization of the pressed materials were carried out. It was found that the microstructure displayed a bimodal grain structure after two passes and then became homogeneous after four passes following both routes A and Bc. The misorientation distribution was examined and the results revealed that the fraction of high angle grain boundaries (HAGB) was higher at temperature 473K. The texture was randomized following route Bc whereas it became strengthened in route A after four passes. According to the Hall-Petch (HP) relationship, the yield stress of polycrystalline metals increases with a decrease in grain size. In this study, a positive slope k was achieved in the strengthened texture while a negative one was obtained in the softened texture. The ductility of ECAP processed material was considerably improved (from 23% to 38%) without sacrificing the yield stress by route Bc at 423K.

scholarly journals Investigation of the Mechanical Properties of St. Lawrence River Ice

1971 ◽  
Vol 8 (2) ◽  
pp. 163-169 ◽  
Author(s):  
L. W. Gold ◽  
A. S. Krausz
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Yield Stress ◽  
Power Law ◽  
River Ice ◽  
Stress Strain ◽  
Strain Behavior ◽  
Brittle Transition ◽  
Ductile To Brittle Transition ◽  
St Lawrence River

Observations are reported on the stress–strain behavior at −9.5 ± 0.5 °C of four types of ice obtained from the St. Lawrence River. The ice was subject to nominal rates of strain covering the range 2.1 × 10−5 min−1 to 5.8 × 10−2 min−1. A ductile-to-brittle transition was observed for strain rate of about 10−2 min−1. In the ductile range the four types had an upper yield stress that increased with strain rate according to a power law.

Sign in / Sign up

Export Citation Format

Share Document