Editorial note to the paper by K. Kalna ?an improved method of calculating critical crack opening?

1975 ◽  
Vol 7 (11) ◽  
pp. 1324-1324
Keyword(s):  
Crack Opening ◽  
Editorial Note ◽  
Improved Method ◽  
Critical Crack ◽  
Critical Crack Opening

Test for Crack Opening Displacement of Steel Fiber Reinforced Concrete under Three-Point Bending

2010 ◽  
Vol 36 ◽  
pp. 157-161 ◽  
Author(s):  
Tin Gyi Zhang ◽  
Yuan Bao Leng ◽  
Dan Ying Gao
Keyword(s):  
Crack Opening Displacement ◽  
Crack Opening ◽  
Mouth Opening ◽  
Crack Tip ◽  
Crack Mouth Opening Displacement ◽  
Crack Tip Opening Displacement ◽  
Opening Displacement ◽  
Critical Crack ◽  
Critical Crack Opening ◽  
Crack Tip Opening

Based on the principle of electrical measurement method, the clip gauge was made to measure the crack opening displacement (COD).Through the three-point bending test on the specimens of steel fiber reinforced high strength concrete (SFHSC), the effect of the fiber volume fraction (ρf) upon the critical crack opening displacement (the critical crack tip opening displacement and the critical crack mouth opening displacement) was studied. The result shows that the effect of ρf on mouth-tip ratio (the ratio of critical crack mouth opening displacement to critical crack tip opening displacement) can reflect its effect upon the critical crack opening displacement. According to the geometrical relationship between the initial crack length and the critical crack opening displacement，calculation method for the initial crack length was proposed. Based on the test result, the formula was established for calculating the critical crack tip opening displacement.

Finite Element Analysis of Brittle Cracking due to Single Grit Rotating Scratch

2003 ◽  
Vol 70 (1) ◽  
pp. 147-151 ◽  
Author(s):  
G. Subhash ◽  
W. Zhang
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Crack Opening ◽  
Damage Zone ◽  
Depth Of Cut ◽  
Opening Displacement ◽  
Element Analysis ◽  
Critical Crack ◽  
Critical Crack Opening ◽  
Brittle Material Removal

Finite element analysis of single grit rotating scratch on brittle materials was conducted using an “elastic-plastic-cracking” (EPC) model. The brittle material removal mechanism was modeled based on a critical crack-opening displacement criterion. It was found that the tangential and normal force profiles as well as the damage morphology observed in scratch experiments were fully captured by the EPC model. The results revealed that the induced damage zone size increases linearly with a brittleness parameter EY/σf21/3 as well as the maximum depth of cut.

The Criterion of Variable COD and CTOA for Numerical Simulation with Aluminum Alloy 2524

2011 ◽  
Vol 261-263 ◽  
pp. 707-711
Author(s):  
Li Jun Shi ◽  
Li Zhong Jiang ◽  
Bang Cheng Yang
Keyword(s):  
Aluminum Alloy ◽  
Crack Opening ◽  
Opening Angle ◽  
Welding Parameters ◽  
Fracture Parameter ◽  
Opening Displacement ◽  
Critical Crack ◽  
Friction Stir ◽  
Critical Crack Opening ◽  
Performance Research

The performance research of Friction Stir Weld’s Joints of Aluminum Alloy under different welding parameters is very necessary and valuable in the engineering. Two points is proposed in this paper. One is the new fracture criterion using the function curve of the value of critical crack opening displacement (|CODc|) as a fracture parameter, the other is using critical crack opening angle (CTOA) as a fracture parameter.

The crack opening displacement approach to fracture mechanics in yielding materials

1966 ◽  
Vol 1 (2) ◽  
pp. 145-153 ◽  
Author(s):  
F. M. Burdekin ◽  
D. E. W. Stone
Keyword(s):  
Fracture Mechanics ◽  
Crack Opening Displacement ◽  
Crack Opening ◽  
Opening Displacement ◽  
Critical Crack ◽  
Absolute Size ◽  
Linear Elastic ◽  
Elastic Fracture ◽  
Critical Crack Opening ◽  
Displacement Approach

An introduction is given to the fracture mechanics approach employing the concept of crack opening displacement for application to situations in which linear elastic fracture mechanics is invalidated by yielding. The hypothesis of a critical crack opening displacement to fracture has been examined experimentally using mild steel specimens of vastly differing dimensions. Subsidiary experiments have been carried out to define the factors responsible for the apparent effect of absolute size on the results. A theoretical analysis simulates elastic-plastic conditions to give a relationship between applied stresses and strains, crack length, and crack opening displacement.

Evaluation of Wedge Splitting Fracture Tests Using the Double-K Model: Analysis of the Effect of Hemp Fibre Dosage and Length in Concrete Specimens

2016 ◽  
Vol 249 ◽  
pp. 142-146
Author(s):  
Hana Šimonová ◽  
Ivana Havlíková ◽  
Jakub Sobek ◽  
Alaa Abdulrahman ◽  
Zbyněk Keršner ◽  
...  
Keyword(s):  
Fracture Toughness ◽  
Crack Propagation ◽  
Crack Opening Displacement ◽  
Crack Opening ◽  
Opening Displacement ◽  
Critical Crack ◽  
Hemp Fibre ◽  
Fracture Tests ◽  
Critical Crack Opening ◽  
Wedge Splitting

This paper deals with the results obtained from the employment of a selected fracture model to evaluate wedge splitting fracture tests carried out on hemp fibre concrete specimens. The research work was focused mainly on the effect of the dosage and length of hemp fibres on the initiation part of crack propagation in concrete specimens, and on critical crack opening displacement. Concrete mixtures with different volumetric dosages (0.5, 1.0 and 2.0 %) and fibre lengths (10, 20 and 40 mm) were prepared, and six identical specimens were cast from each mixture. Specimens were also cast from a reference mixture, which was without fibres. The specimens were provided with an initial notch and tested using the wedge splitting test method. Load versus crack mouth opening displacement diagrams were recorded during testing and (after data filtering and appropriate modifications) subsequently evaluated using the Double-K fracture model. This model allows the evaluation of two material parameters – the initiation fracture toughness, which defines the onset of stable crack propagation, and the unstable fracture toughness, which defines the onset of unstable cracking or failure. Finally, the critical crack opening displacement was determined with the assumption of the bilinear function of softening in tension.

Sign in / Sign up

Export Citation Format

Share Document