Increasing the efficiency of mining equipment at the Komsomol Mining Commission

Refractories ◽  
1971 ◽  
Vol 12 (3-4) ◽  
pp. 162-162
Author(s):  
A. V. Anikeev ◽  
A. P. Pomorgailo
Keyword(s):  
Mining Equipment ◽  
Mining Commission

Advanced Systems to Prevent Collisions of Mining Equipment and Personnel Accidents in Surface Mining

2020 ◽  
pp. 24-29
Author(s):  
A.F. Klebanov ◽  
M.V. Kadochnikov ◽  
V.V. Ulitin ◽  
D.N. Sizemov
Keyword(s):  
Human Life ◽  
Surface Mining ◽  
Production Cycle ◽  
Mining Equipment ◽  
Mining Operations ◽  
Emergency Situations ◽  
Surface Mines ◽  
Technical Requirements ◽  
Personal Devices ◽  
Blind Spots

The article addresses the issues of ensuring safe operation of mining equipment in surface mining. It describes the main factors and situations that pose a high risk to human life and health. The most dangerous incidents are shown to be related to limited visibility and blind spots for operators of mining equipment, which can result in collisions and personnel run over. The main technologies and specific solutions used to design collision avoidance systems are described and their general comparison is provided. A particular focus is placed on monitoring the health of employees at their workplace by means of portable personal devices that promptly inform the dispatcher of emergency situations. General technical requirements are formulated for designing of the system to prevent equipment collisions and personnel run over in surface mining operations. The paper emphasizes the importance of introducing a multifunctional safety system in surface mines in order to minimise the possibility of incidents and accidents throughout the entire production cycle.

TRI-MARK TM-115

Alloy Digest ◽  
1983 ◽  
Vol 32 (8) ◽  
Keyword(s):  
Fracture Toughness ◽  
Corrosion Resistance ◽  
Arc Welding ◽  
High Strength ◽  
Heat Treating ◽  
Low Alloy Steels ◽  
Mining Equipment ◽  
Alloy Steels ◽  
Temperature Impact ◽  
Welding Electrode

Abstract TRI-MARK TM-115 is a gas-shielded flux-cored welding electrode for continuous high deposition are welding. It is designed specifically for semiautomatic and automatic arc welding of high-strength low-alloy steels and quenched-and-tempered steels. This gas-sheilded tubular wire can be used for single and multiple-pass welding. It has outstanding low-temperature impact properties. Its applications including mining equipment, large vehicles and similar items. This datasheet provides information on composition, physical properties, elasticity, and tensile properties as well as fracture toughness. It also includes information on corrosion resistance as well as heat treating, machining, and joining. Filing Code: SA-392. Producer or source: Tri-Mark Inc..

On effect of surface hardening on impact and abrasive wear resistance of Hadfi eld steel

2020 ◽  
pp. 252-255
Author(s):  
V.I. Bolobov ◽  
V.S. Bochkov ◽  
E.V. Akhmerov ◽  
V.A. Plashchinsky ◽  
E.A. Krivokrisenko E.A.
Keyword(s):  
Plastic Deformation ◽  
Wear Resistance ◽  
Abrasive Wear ◽  
Work Hardening ◽  
Surface Hardening ◽  
Cold Work ◽  
Abrasive Wear Resistance ◽  
Hadfield Steel ◽  
Mining Equipment ◽  
Effect Of Surface

On the example of Hadfield steel, as the most common material of fast-wearing parts of mining equipment, the effect of surface hardening by plastic deformation on their impact and abrasive wear resistance is considered. Wear test is conducted on magnetic ironstone as typical representative of abrasive and hard rock. As result of wear of initial samples with hardness of ∼200 HB and samples pre-hardened with different intensities to the hardness of 300, 337 and 368 HB, it is found that during the initial testing period, the initial samples pass the “self-cold-work hardening” stage with increase in hardness to ∼250 HB, which remains virtually unchanged during further tests; the hardness of the pre-hardened samples does not change significantly throughout the tests. It is established that the rate of impact-abrasive wear of pre-hardened samples is significantly (up to 1.4 times) lower than the original ones that are not subjected to plastic deformation, and decreases with increasing degree of cold-work hardening. Preliminary surface hardening by plastic deformation can serve as effective way to increase the service life of fast-wearing working parts of mining equipment.

Corrosion of Welded Metal Structures of Mining Equipment

2018 ◽  
Vol 69 (9) ◽  
pp. 2563-2566
Author(s):  
Dan Dobrota
Keyword(s):  
Carbon Concentration ◽  
Welded Joints ◽  
Construction Material ◽  
Working Environment ◽  
Mining Equipment ◽  
Metal Structures ◽  
Corrosion Phenomenon ◽  
Welding Regime ◽  
New Material ◽  
Initial Research

Mining equipment made of welded metal structures is strongly affected by the corrosion phenomenon due to the working conditions. Initial research has shown that the corrosion phenomenon is most pronounced in the area of cross-welded joints and welded T-shaped joints. In the researches, there was made a chemical analysis of the welded construction material used respectively of the new material and it was observed a reduction in carbon concentration in the material used, but also a substantial increase in the sulfur concentration compared to the new material. The pronounced corrosion of the metallic structure is influenced by the chemical composition change because the sulfur is a grafitizing and weakening element, and the decrease in carbon concentration causes a decrease in corrosion resistance. Also, the pronounced corrosion is due to the action of sulfurous acid (H2SO3) and hydrogen sulfide (H2S), elements that are present in the working environment of welded constructions. In order to achieve a reduction in the corrosion phenomenon, it is very important that the welded joints are made using the optimal parameters of the welding regime so as to obtain metallographic structure with finer granulations.

scholarly journals A Multiple Criteria Decision Making Method to Weight the Sustainability Criteria of System Selection for Surface Mining

Energies ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3066
Author(s):  
Michał Patyk ◽  
Przemysław Bodziony ◽  
Zbigniew Krysa
Keyword(s):  
Decision Making ◽  
Performance Assessment ◽  
Multiple Criteria Decision Making ◽  
Surface Mining ◽  
Open Pit ◽  
Mining Equipment ◽  
Surface Mines ◽  
Mining Conditions ◽  
And Performance ◽  
Selection Of

Selection and assessment of mining equipment used in open pit rock mines relies chiefly on estimates of overall exploitation cost. The rational arrangement of mining equipment and systems comprising loading machines, haul trucks and crushing plants should be preceded by a thorough analysis of technical and economic aspects, such as investment outlays and the costs of further exploitation, which largely determine the costs of mining operations and the deposit value. Additionally, the operational parameters of the mining equipment ought to be considered. In this study, a universal set of evaluation criteria has been developed, and an evaluation method has been applied for the selection of surface mining equipment and the processing system to be operated in specific mining conditions, defined by the user. The objective of this study is to develop and apply the new methodology of multi-criteria selection of open pit rock mining equipment based on multiple criteria decision-making (MCDM) procedures, to enable the optimization of loading, handling and crushing processes. The methodology, underpinned by the principles of MCDM, provides the dedicated ranking procedures, including the ELECTRE III. The applied methodology allows the alternative options (variants) to be ranked accordingly. Ultimately, a more universal methodology is developed, applicable in other surface mines where geological and mining conditions are similar. It may prove particularly useful in selection and performance assessment of mining equipment and process line configurations in mining of low-quality rock deposits. Therefore, we undertook to develop universal criteria and applications for the selection and performance assessment of process machines for surface mines, taking into account environmental aspects as well as deposit quality.

Sign in / Sign up

Export Citation Format

Share Document