On the description of cyclic creep and rate dependent plastic deformation

1985 ◽  
Vol 55 (1-2) ◽  
pp. 123-136 ◽  
Author(s):  
M. O. Faruque
Keyword(s):  
Plastic Deformation ◽  
Cyclic Creep ◽  
Rate Dependent

STRAIN RATE–DEPENDENT BEHAVIOR OF UNCURED RUBBER: EXPERIMENTAL INVESTIGATION AND CONSTITUTIVE MODELING

2022 ◽  
Author(s):  
Sanghyeub Kim ◽  
Thomas Berger ◽  
Michael Kaliske
Keyword(s):  
Strain Rate ◽  
Evolution Equations ◽  
Cyclic Creep ◽  
Tensile Tests ◽  
Internal Variables ◽  
Creep Tests ◽  
Rate Dependent ◽  
Nonlinear Viscosity ◽  
Dependent Behavior ◽  
Building Process

ABSTRACT The strain rate dependence of uncured rubber is investigated through a series of tensile tests (monotonic, multistep relaxation, cyclic creep tests) at different strain rates. In addition, loading/unloading tests in which the strain rate is varied every cycle are carried out to observe their dependence on the deformation history. A strain rate–dependent viscoelastic–viscoplastic constitutive model is proposed with the nonlinear viscosity and process-dependent recovery properties observed in the test results. Those properties are implemented by introducing evolution equations for additional internal variables. The identified material parameters capture the experiments qualitatively well. The proposed model is also evaluated by finite element simulations of the building process of a tire, followed by the in-molding.

Analysis of Plastic Deformation in Metal-Ceramic Nanolayers During Cyclic Indentation

2012 ◽  
Author(s):  
C. B. Blada ◽  
Y.-L. Shen
Keyword(s):  
Plastic Deformation ◽  
Transient Behavior ◽  
Primary Objective ◽  
Cyclic Plasticity ◽  
Rate Dependent ◽  
Diamond Indenter ◽  
Metal Ceramic ◽  
Elastic Loading ◽  
Cyclic Indentation ◽  
And Control

The indentation behavior of metal/ceramic nanolayers is studied, with attention devoted to cyclic response under fixed maximum and minimum indentation loads. The primary objective is to examine the evolving plastic deformation in the ductile metal constrained by the hard ceramic layers. The model consists of alternating aluminum (Al) and silicon carbide (SiC) thin films on a silicon substrate, with the Al/SiC layered structure being indented by a diamond indenter. The rate-dependent viscoplastic response of Al is taken into account in the numerical model. It is shown that plastic deformation in the ductile Al layers continues to occur during the unloading phase of the first cycle, as well as during subsequent reload/unload processes. The cyclic plasticity results in an open load-displacement loop, and the indenter continues to move deeper with each cycle. For the control model of a homogeneous Al film, there is no hysteresis loop and the transient behavior soon approaches stabilization, showing repetitive elastic loading/unloading. The modeling results are also compared with cyclic nanoindentation experiments conducted on the same metal-ceramic multilayer system and control specimen.

Strain Rate Sensitivity of Commercial Aluminum Alloys

2019 ◽  
Author(s):  
R.C. Picu
Keyword(s):  
Plastic Deformation ◽  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Solid Solutions ◽  
Elevated Temperatures ◽  
Rate Sensitivity ◽  
Solute Diffusion ◽  
Rate Dependent ◽  
Ultrafine Grained ◽  
Using Data

This article presents a review of the strain rate-dependent mechanical behavior of aluminum and its commercial alloys. The importance of strain rate sensitivity (SRS) stems from its relation with ductility and formability. Plastic deformation is stable and localization less likely in alloys with higher SRS. After discussing the basic formulation used to interpret experimental data, the methods used to measure the SRS parameter are presented. This is followed by a brief review of the main mechanisms that render the flow stress sensitive to the deformation rate, including mechanisms leading to positive and negative SRS. The generic dependence of the SRS parameter on the strain, temperature, and strain rate are further presented using data for pure Al. The effect of alloying is analyzed in the context of solid solutions and precipitated commercial alloys. Results on solid solutions are discussed separately at low and elevated temperatures in order to evidence the role of solute diffusion on SRS. This article ends with a brief discussion of the grain size dependence of SRS, with emphasis on recent efforts to produce nanocrystalline and ultrafine-grained materials by severe plastic deformation.

scholarly journals Strain rate dependence of plastic flow in Ce-based bulk metallic glass during nanoindentation

2007 ◽  
Vol 22 (2) ◽  
pp. 258-263 ◽  
Author(s):  
B.C. Wei ◽  
L.C. Zhang ◽  
T.H. Zhang ◽  
D.M. Xing ◽  
J. Das ◽  
...  
Keyword(s):  
Plastic Deformation ◽  
Metallic Glass ◽  
Strain Rate ◽  
Bulk Metallic Glass ◽  
Loading Rate ◽  
Shear Banding ◽  
Rate Dependence ◽  
Strain Rate Dependence ◽  
Serrated Flow ◽  
Rate Dependent

The strain rate dependence of plastic deformation of Ce60Al15Cu10Ni15 bulk metallic glass was studied by nanoindentation. Even though the ratio of room temperature to the glass transition temperature was very high (0.72) for this alloy, the plastic deformation was dominated by shear banding under nanoindentation. The alloy exhibited a critical loading rate dependent serrated flow feature. That is, with increasing loading rate, the alloy exhibited a transition from less prominent serrated flow to pronounced serrated flow during continuous loading but from serrated to smoother flow during stepped loading.

Ductile Fracture of Rapidly Expanding Rings

1983 ◽  
Vol 50 (3) ◽  
pp. 593-600 ◽  
Author(s):  
J. N. Johnson
Keyword(s):  
Growth Rate ◽  
Plastic Deformation ◽  
Differential Equations ◽  
Spatial Dimension ◽  
Momentum Conservation ◽  
Thermal Softening ◽  
Sectional Area ◽  
Cross Sectional ◽  
Rate Dependent ◽  
Work Hardening Rate

Heterogeneous plastic deformation (necking) of thin ductile rings given an initial outward impulse is described in terms of the ordinary differential equations of thermoplasticity and the partial differential equations of mass and momentum conservation in one spatial dimension (circumference) and time. Flaws in cross-sectional area and porosity are introduced and the resulting plastic deformation is calculated numerically for a prescribed initial radial velocity. Plastic deformation is initially homogeneous but soon concentrates in the weakest region, which then thins rapidly and fractures. Effects of flaw wavelength, work-hardening rate, thermal softening, and rate-dependent plastic flow on the flaw growth rate are studied.

Sign in / Sign up

Export Citation Format

Share Document