Experimental study of a hot plasma produced by injection of electrons

1967 ◽  
Vol 23 (3) ◽  
pp. 923-929
Author(s):  
B. S. Akshanov ◽  
Yu. Ya. Volkolupov ◽  
K. D. Sinel'nikov ◽  
A. M. Smirnov
Keyword(s):  
Experimental Study ◽  
Hot Plasma

Experimental study of an electroacoustic wave excited by an antenna in a hot plasma

1967 ◽  
Vol 55 (9) ◽  
pp. 1656-1657 ◽  
Author(s):  
K.M. Chen ◽  
H. Judson ◽  
C.C. Lin
Keyword(s):  
Experimental Study ◽  
Hot Plasma ◽  
Electroacoustic Wave

Electron microscopy studies of plasma-sprayed materials

1983 ◽  
Vol 41 ◽  
pp. 70-71
Author(s):  
K.R. Subramanian ◽  
A.H. King ◽  
H. Herman
Keyword(s):  
Plasma Spraying ◽  
Substrate Surface ◽  
Flame Temperature ◽  
Ceramic Coatings ◽  
Metallic Substrates ◽  
Hot Plasma ◽  
Almost All ◽  
Plasma Sprayed ◽  
Hostile Environments ◽  
Plasma Spraying Process

Plasma spraying is a technique which is used to apply coatings to metallic substrates for a variety of purposes, including hardfacing, corrosion resistance and thermal barrier applications. Almost all of the applications of this somewhat esoteric fabrication technique involve materials in hostile environments and the integrity of the coatings is of paramount importance: the effects of process variables on such properties as adhesive strength, cohesive strength and hardness of the substrate/coating system, however, are poorly understood.Briefly, the plasma spraying process involves forming a hot plasma jet with a maximum flame temperature of approximately 20,000K and a gas velocity of about 40m/s. Into this jet the coating material is injected, in powder form, so it is heated and projected at the substrate surface. Relatively thick metallic or ceramic coatings may be speedily built up using this technique.

Experimental study on the restoration from a tilt-azimuth series for improvement in resolution

1995 ◽  
Vol 53 ◽  
pp. 636-637
Author(s):  
Norio Baba ◽  
Norihiko Ichise ◽  
Syunya Watanabe
Keyword(s):  
Experimental Study ◽  
Spherical Aberration ◽  
Incident Beam ◽  
Optical Parameters ◽  
Beam Tilting ◽  
Illumination Method ◽  
Restoration Method ◽  
Illumination Mode

The tilted beam illumination method is used to improve the resolution comparing with the axial illumination mode. Using this advantage, a restoration method of several tilted beam images covering the full azimuthal range was proposed by Saxton, and experimentally examined. To make this technique more reliable it seems that some practical problems still remain. In this report the restoration was attempted and the problems were considered. In our study, four problems were pointed out for the experiment of the restoration. (1) Accurate beam tilt adjustment to fit the incident beam to the coma-free axis for the symmetrical beam tilting over the full azimuthal range. (2) Accurate measurements of the optical parameters which are necessary to design the restoration filter. Even if the spherical aberration coefficient Cs is known with accuracy and the axial astigmatism is sufficiently compensated, at least the defocus value must be measured. (3) Accurate alignment of the tilt-azimuth series images.

An Experimental Study of Some Properties of Stuttered Words

1962 ◽  
Vol 5 (4) ◽  
pp. 387-394 ◽  
Author(s):  
Bruce Quarrington ◽  
Jerome Conway ◽  
Nathan Siegel
Keyword(s):  
Experimental Study

Experimental study of total body washout employing extracorporeal circulation and hypothermia

1974 ◽  
Vol 126 (2) ◽  
pp. 243-248
Author(s):  
A WAKABAYASHI ◽  
T KUBO ◽  
K CHARNEY ◽  
Y NAKAMURA ◽  
J CONNOLLY
Keyword(s):  
Experimental Study ◽  
Extracorporeal Circulation ◽  
Total Body

Gastric Freezing: An Experimental Study

1963 ◽  
Vol 45 (3) ◽  
pp. 374-383 ◽  
Author(s):  
Donald C. McIlrath ◽  
George A. Hallenbeck ◽  
Hubert A. Allen ◽  
Charles V. Mann ◽  
Edward J. Baldes ◽  
...  
Keyword(s):  
Experimental Study
Sign in / Sign up

Export Citation Format

Share Document