Dislocation structure of copper produced by a high-intensity electron pulse of length 10?8?10?7 sec

1975 ◽  
Vol 18 (3) ◽  
pp. 404-405 ◽  
Author(s):  
V. P. Rotshtein ◽  
L. S. Bushnev ◽  
D. I. Proskurovskii
Keyword(s):  
Dislocation Structure ◽  
High Intensity ◽  
Electron Pulse

Primary Yields and Mechanisms in the Radiolysis of N2O from High Intensity Electron Pulse Irradiations of N2O–O2 Mixtures

1972 ◽  
Vol 50 (10) ◽  
pp. 1557-1567 ◽  
Author(s):  
C. Willis ◽  
A. W. Boyd ◽  
P. E. Bindner
Keyword(s):  
High Intensity ◽  
Reaction Rate ◽  
Electron Pulse ◽  
Rate Data

The yields of N2, O2, NO, and O3 have been measured from the Febetron radiolysis of N2O–O2 mixtures with and without SF6. A mechanism consistent with the yields from 0–100% O2 and with known ionic abundances and reaction rate data has been derived. The major features of this mechanism are both dissociative neutralization of N2O+ and excitation of N2O to give N2(X1Σ) and O(1D) and smaller amounts of N2(B3Π) and O(3P). The large yields of NO and N2 observed are mainly due to reaction of O(1D) with N2O to give both N2 and O2 and NO.

Interaction of excitons created by a high intensity electron pulse in naphthalene crystal

1976 ◽  
Vol 12-13 ◽  
pp. 253-257 ◽  
Author(s):  
T. Nakayama ◽  
M. Higuchi ◽  
S. Fujiwara ◽  
N. Itoh
Keyword(s):  
High Intensity ◽  
Electron Pulse ◽  
Naphthalene Crystal

The dislocation structure of a 10° [110] tilt boundary in silicon

1983 ◽  
Vol 41 ◽  
pp. 114-115
Author(s):  
B. Cunningham ◽  
D.G. Ast
Keyword(s):  
Dislocation Structure ◽  
Tilt Angle ◽  
Imaging Technique ◽  
Diamond Lattice ◽  
Tilt Boundary ◽  
Formation Mechanisms ◽  
Diffraction Contrast ◽  
Lattice Fringe ◽  
Tilt Boundaries ◽  
Chemically Vapor Deposited

There have Been a number of studies of low-angle, θ < 4°, [10] tilt boundaries in the diamond lattice. Dislocations with Burgers vectors a/2<110>, a/2<112>, a<111> and a<001> have been reported in melt-grown bicrystals of germanium, and dislocations with Burgers vectors a<001> and a/2<112> have been reported in hot-pressed bicrystals of silicon. Most of the dislocations were found to be dissociated, the dissociation widths being dependent on the tilt angle. Possible dissociation schemes and formation mechanisms for the a<001> and a<111> dislocations from the interaction of lattice dislocations have recently been given.The present study reports on the dislocation structure of a 10° [10] tilt boundary in chemically vapor deposited silicon. The dislocations in the boundary were spaced about 1-3nm apart, making them difficult to resolve by conventional diffraction contrast techniques. The dislocation structure was therefore studied by the lattice-fringe imaging technique.

Mechanical Properties and Dislocation Structure of Single Crystal Cdte Deformed in Compression at 300°C

1976 ◽  
Vol 34 ◽  
pp. 592-593
Author(s):  
Ernest L. Hall ◽  
J. B. Vander Sande
Keyword(s):  
Mechanical Properties ◽  
Single Crystal ◽  
Dislocation Structure ◽  
Room Temperature ◽  
Elevated Temperatures ◽  
Strain Curve ◽  
Optical Devices ◽  
Semiconductor Compound ◽  
Wide Range ◽  
Sample Orientation

The present paper describes research on the mechanical properties and related dislocation structure of CdTe, a II-VI semiconductor compound with a wide range of uses in electrical and optical devices. At room temperature CdTe exhibits little plasticity and at the same time relatively low strength and hardness. The mechanical behavior of CdTe was examined at elevated temperatures with the goal of understanding plastic flow in this material and eventually improving the room temperature properties. Several samples of single crystal CdTe of identical size and crystallographic orientation were deformed in compression at 300°C to various levels of total strain. A resolved shear stress vs. compressive glide strain curve (Figure la) was derived from the results of the tests and the knowledge of the sample orientation.

Observations of dislocation interactions with recrystallized grain boundaries

1988 ◽  
Vol 46 ◽  
pp. 628-629
Author(s):  
C. W. Price
Keyword(s):  
Dislocation Density ◽  
Grain Boundary ◽  
Strain Rate ◽  
Grain Boundaries ◽  
Dislocation Structure ◽  
Hot Deformation ◽  
Static Recrystallization ◽  
High Dislocation Density ◽  
High Angle ◽  
Dislocation Interactions

Little evidence exists on the interaction of individual dislocations with recrystallized grain boundaries, primarily because of the severely overlapping contrast of the high dislocation density usually present during recrystallization. Interesting evidence of such interaction, Fig. 1, was discovered during examination of some old work on the hot deformation of Al-4.64 Cu. The specimen was deformed in a programmable thermomechanical instrument at 527 C and a strain rate of 25 cm/cm/s to a strain of 0.7. Static recrystallization occurred during a post anneal of 23 s also at 527 C. The figure shows evidence of dissociation of a subboundary at an intersection with a recrystallized high-angle grain boundary. At least one set of dislocations appears to be out of contrast in Fig. 1, and a grainboundary precipitate also is visible. Unfortunately, only subgrain sizes were of interest at the time the micrograph was recorded, and no attempt was made to analyze the dislocation structure.

Bright field and weak-beam images of dislocations gliding on (001) planes in F.C.C. metals

1978 ◽  
Vol 36 (1) ◽  
pp. 352-353
Author(s):  
H. P. Karnthaler ◽  
A. Korner
Keyword(s):  
Single Crystals ◽  
Dislocation Structure ◽  
Room Temperature ◽  
Stage Ii ◽  
Bright Field ◽  
Weak Beam ◽  
Standard Orientation

In f.c.c. metals slip is observed to occur generally on {111} planes. Glide dislocations on intersecting {111} planes can react with each other and form Lomer-Cottrell locks which lie along a <110> direction and are sessile since they are split on two {111} planes. Cottrell already pointed out that these dislocations could glide on {001} planes if they were not split. The first study of this phenomenon has been published recently. It is the purpose of this paper to report some interesting new details of the dislocations gliding on {001} planes in pure Ni, Cu, and Ag deformed at room temperature.Single crystals are grown with standard orientation and strained into stage II. The crystals are sliced parallel to the (001) planes. The dislocation structure is studied by TEM and the Burgers vectors ḇ and glide planes of the dislocations are determined unambiguously.In Fig.l primary P and secondary S dislocations react and form composite dislocations K.

A New High Intensity Grid Cap for RCA-EMU-3 Electron Microscopes

1968 ◽  
Vol 26 ◽  
pp. 316-317
Author(s):  
George Christov ◽  
Bolivar J. Lloyd
Keyword(s):  
Electron Beam ◽  
Electron Microscope ◽  
High Voltage ◽  
High Intensity ◽  
Electron Gun ◽  
Tungsten Filament ◽  
Fluorescent Screen ◽  
Electron Microscopes ◽  
Pass Through ◽  
Ground Potential

A new high intensity grid cap has been designed for the RCA-EMU-3 electron microscope. Various parameters of the new grid cap were investigated to determine its characteristics. The increase in illumination produced provides ease of focusing on the fluorescent screen at magnifications from 1500 to 50,000 times using an accelerating voltage of 50 KV.The EMU-3 type electron gun assembly consists of a V-shaped tungsten filament for a cathode with a thin metal threaded cathode shield and an anode with a central aperture to permit the beam to course the length of the column. The cathode shield is negatively biased at a potential of several hundred volts with respect to the filament. The electron beam is formed by electrons emitted from the tip of the filament which pass through an aperture of 0.1 inch diameter in the cap and then it is accelerated by the negative high voltage through a 0.625 inch diameter aperture in the anode which is at ground potential.

The butterfly martensite nucleation in an iron and nickel alloy

1990 ◽  
Vol 48 (4) ◽  
pp. 906-907
Author(s):  
Q.Z. Chen ◽  
X.F. Wu ◽  
T. Ko
Keyword(s):  
Nickel Alloy ◽  
Ethyl Alcohol ◽  
Dislocation Structure ◽  
Martensite Transformation ◽  
Room Temperature ◽  
The Matrix

Some butterfly martensite nuclei were observed in an Fe-27.6Ni-0.89V-0.05C alloy. The alloy was austenitized at 1200°C for 1 hour. Some samples were aged at 850° C for 40 minutes and quenched in 10% brine at room temperature. All the samples were cooled in ethyl alcohol for martensite transformation.A nucleus in an unaged specimen is shown in Fig.1. The nucleus has certain contrast different from the matrix and is shaped like one wing of a butter fly martensite. The SADP of the circled region is measured to be: da=dh, and approximate to dγ(111) and dm(110) with ∠AOB = 55° . It is similar to [011]f.c.c and b patterns in the anglez ∠AOB and the ratio ra/rb, respectively. The SADP shows that the structure of the nucleus is between f.c.c and b.c.c. The dislocation structure within the nucleus is shown in Fig.2. Their Burgers vectors and line directions are also given in it. There are many long dislocations near it without dislocations piled up as shown in Fig.3.Long dislocations are closed at one end as an envelope.

260: High Intensity Focused Ultrasound Combined with Endocrine Therapy in Treating High or Intermediate Risk Prostate Cancer

2006 ◽  
Vol 175 (4S) ◽  
pp. 86-86
Author(s):  
Makoto Sumitomo ◽  
Junichi Asakuma ◽  
Yasumasa Hanawa ◽  
Kazuhiko Nagakura ◽  
Masamichi Hayakawa
Keyword(s):  
Prostate Cancer ◽  
Endocrine Therapy ◽  
High Intensity ◽  
Focused Ultrasound ◽  
High Intensity Focused Ultrasound ◽  
Intermediate Risk ◽  
Risk Prostate Cancer

1400: Early Clinical Experience Using High-Intensity Focused Ultrasound for the Treatment of Renal Tumours

2005 ◽  
Vol 173 (4S) ◽  
pp. 379-380
Author(s):  
James E. Kennedy ◽  
Rowland O. Illing ◽  
Feng Wu ◽  
Gail R. ter Haar ◽  
Rachel R. Phillips ◽  
...  
Keyword(s):  
Clinical Experience ◽  
High Intensity ◽  
Focused Ultrasound ◽  
High Intensity Focused Ultrasound ◽  
Early Clinical Experience ◽  
Renal Tumours
Sign in / Sign up

Export Citation Format

Share Document