Delayed fracture of a plate made of an orthotropic viscoelastic composite with a central crack under a constant load

1991 ◽  
Vol 27 (11) ◽  
pp. 1104-1111
Author(s):  
A. A. Kaminskii ◽  
S. A. Kekukh
Keyword(s):  
Constant Load ◽  
Delayed Fracture ◽  
Viscoelastic Composite ◽  
Central Crack

Constant-load delayed fracture test of atmospherically corroded high strength steels

2011 ◽  
Vol 257 (19) ◽  
pp. 8275-8281 ◽  
Author(s):  
Eiji Akiyama ◽  
Katsuhiro Matsukado ◽  
Songjie Li ◽  
Kaneaki Tsuzaki
Keyword(s):  
High Strength Steels ◽  
High Strength ◽  
Constant Load ◽  
Fracture Test ◽  
Delayed Fracture

Fatigue of Unidirectional Cord-Rubber Composites

1999 ◽  
Vol 27 (1) ◽  
pp. 48-57 ◽  
Author(s):  
Y. Liu ◽  
Z. Wan ◽  
Z. Tian ◽  
X. Du ◽  
J. Jiang ◽  
...  
Keyword(s):  
Damage Accumulation ◽  
Fatigue Testing ◽  
Fatigue Behavior ◽  
Constant Load ◽  
Testing System ◽  
Rubber Composites ◽  
Cycle Frequency ◽  
Periodic Loading ◽  
Fatigue Damage Accumulation ◽  
Rubber Composite

Abstract A fatigue testing system is established with which the real-time recording of stress, strain, temperature, and hysteresis loss of rubbers or cord-rubber composite specimens subjected to periodic loading or extension can be successfully carried out. Several problems are connected with the experimental study of the fatigue of rubber composites. In constant extension cycling, the specimen becomes relaxed because of the viscoelasticity of rubber composites, and the imposed tension-tension deformation becomes complex. In this method, the specimen is unlikely to fail unless the imposed extensions are very large. Constant load cycling can avoid the shortcomings of constant extension cycling. The specially designed clamps ensure that the specimen does not slip when the load retains a constant value. The Deformation and fatigue damage accumulation processes of rubber composites under periodic loading are also examined. Obviously, the effect of cycle frequency on the fatigue life of rubber composites can not be ignored because of the viscoelasticity of constituent materials. The increase of specimen surface temperature is relatively small in the case of 1 Hz, but the temperature can easily reach 100°C at the 8 Hz frequency. A method for evaluating the fatigue behavior of tires is proposed.

Exercise slightly above the maximal lactate steady state reduces self-efficacy and increases negative affect

2019 ◽  
Author(s):  
James Graeme Wrightson ◽  
Louis Passfield
Keyword(s):  
Steady State ◽  
Negative Affect ◽  
Power Output ◽  
Self Efficacy ◽  
Repeated Measures ◽  
Physiological State ◽  
Constant Load ◽  
Peak Power Output ◽  
Time To Exhaustion ◽  
Maximal Lactate Steady State

Objectives: To examine the effect of exercise at and slightly above the maximal lactate steady state (MLSS) on self-efficacy, affect and effort, and their associations with exercise tolerance.Design: Counterbalanced, repeated measures designMethod: Participants performed two 30‐minute constant‐load cycling exercise at a power output equal to that at MLSS and 10 W above MLSS, immediately followed by a time‐to‐exhaustion test at 80% of their peak power output. Self-efficacy, affect and effort were measured before and after 30 minutes of cycling at and above MLSS.Results: Negative affect and effort higher, and self-efficacy and time to exhaustion were reduced, following cycling at MLSS + 10 W compared to cycling at the MLSS. Following exercise at the MLSS self-efficacy, affect and effort were all associated with subsequent time-to exhaustion. However, following exercise at MLSS + 10 W, only affect was associated with time-to exhaustion. Conclusions: Self efficacy, affect and effort are profoundly affected by physiological state, highlighting the influence of somatic states on perceptions and emotions during exercise. The affective response to exercise appears to be associated with exercise tolerance, indicating that the emotional, as well as physiological, responses should be considered when prescribing exercise training.

Root Cause Analysis of a Connector Time-Delayed Fracture

2015 ◽  
Author(s):  
Prabjit Singh ◽  
Ying Yu ◽  
Robert E. Davis
Keyword(s):  
Printed Circuit Board ◽  
Ceramic Substrate ◽  
Circuit Board ◽  
Delayed Fracture ◽  
Ceramic Substrates ◽  
Printed Circuit ◽  
Root Cause ◽  
Chip Carrier ◽  
Electrical Connections ◽  
Grain Boundary Grooves

Abstract A land-grid array connector, electrically connecting an array of plated contact pads on a ceramic substrate chip carrier to plated contact pads on a printed circuit board (PCB), failed in a year after assembly due to time-delayed fracture of multiple C-shaped spring connectors. The land-grid-array connectors analyzed had arrays of connectors consisting of gold on nickel plated Be-Cu C-shaped springs in compression that made electrical connections between the pads on the ceramic substrates and the PCBs. Metallography, fractography and surface analyses revealed the root cause of the C-spring connector fracture to be plating solutions trapped in deep grain boundary grooves etched into the C-spring connectors during the pre-plating cleaning operation. The stress necessary for the stress corrosion cracking mechanism was provided by the C-spring connectors, in the land-grid array, being compressed between the ceramic substrate and the printed circuit board.

Sign in / Sign up

Export Citation Format

Share Document