Determination of the thermal boundary conditions from nonstationary-temperature measurement data

1981 ◽  
Vol 41 (1) ◽  
pp. 774-778
Author(s):  
V. I. Zhuk ◽  
S. A. Il'in ◽  
D. N. Chubarov
Keyword(s):  
Boundary Conditions ◽  
Temperature Measurement ◽  
Measurement Data ◽  
Nonstationary Temperature ◽  
Thermal Boundary Conditions

Identification of the Boundary Conditions in the Continuous Casting of Steel

2012 ◽  
Vol 57 (1) ◽  
pp. 385-393 ◽  
Author(s):  
M. Rywotycki ◽  
K. Miłkowska-Piszczek ◽  
L. Trębacz
Keyword(s):  
Continuous Casting ◽  
Boundary Conditions ◽  
Continuous Casting Of Steel ◽  
Average Heat Transfer Coefficient ◽  
The Finite Element Method ◽  
Secondary Cooling ◽  
Average Heat ◽  
Thermal Boundary Conditions ◽  
Complex Models

Identification of the Boundary Conditions in the Continuous Casting of SteelThe results of investigations relating the determination of thermal boundary conditions for continuous casting of steel were presented in the paper. The slab of dimensions 1100 mm x 220 mm was analyzed. In numerical calculations two models were compared. The first was the simple one and it used average heat transfer coefficient in both cooling zones. The second one used complex models in primary and secondary cooling zones. The presented models were verified on basing on an industrial data base. The problem was solved by the finite element method and the commercial numerical packet ProCAST.

Inverse Determination of Steady Heat Convection Coefficient Distributions

1998 ◽  
Vol 120 (2) ◽  
pp. 328-334 ◽  
Author(s):  
T. J. Martin ◽  
G. S. Dulikravich
Keyword(s):  
Heat Transfer ◽  
Heat Conduction ◽  
Boundary Conditions ◽  
Measurement Data ◽  
Cost Effective ◽  
Heat Fluxes ◽  
Transfer Coefficients ◽  
Simple Modification ◽  
Heat Transfer Coefficients ◽  
Thermal Boundary Conditions

An inverse Boundary Element Method (BEM) procedure has been used to determine unknown heat transfer coefficients on surfaces of arbitrarily shaped solids. The procedure is noniterative and cost effective, involving only a simple modification to any existing steady-state heat conduction BEM algorithm. Its main advantage is that this method does not require any knowledge of, or solution to, the fluid flow field. Thermal boundary conditions can be prescribed on only part of the boundary of the solid object, while the heat transfer coefficients on boundaries exposed to a moving fluid can be partially or entirely unknown. Over-specified boundary conditions or internal temperature measurements on other, more accessible boundaries are required in order to compensate for the unknown conditions. An ill-conditioned matrix results from the inverse BEM formulation, which must be properly inverted to obtain the solution to the ill-posed problem. Accuracy of numerical results has been demonstrated for several steady two-dimensional heat conduction problems including sensitivity of the algorithm to errors in the measurement data of surface temperatures and heat fluxes.

Large Thrust Bearing Modeling: Influence of Thermal Boundary Conditions and Runner Deformations on Results of TEHD Analysis

2011 ◽  
Author(s):  
Michal Wodtke ◽  
Michel Fillon ◽  
Andreas Schubert ◽  
Michal Wasilczuk
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Boundary Conditions ◽  
Thrust Bearing ◽  
Measurement Data ◽  
Water Power ◽  
Thermal Boundary Conditions ◽  
Side Walls ◽  
Theoretical Results ◽  
Bearing System

In the paper, numerical TEHD results for one of the biggest water power plant Itaipu were compared to available measurement data. Numerical simulations were carried out with the use of bearing model for which the accuracy was previously confirmed with the measurements available for smaller bearings. Several cases were analyzed. The only differences between the cases are the applied boundary conditions. The influence of heat transfer coefficient assumed at bearing pad side walls and collar deformation on predicted bearing performance was determined. Some conclusions concerning large thrust bearing modeling were drawn on the basis of comparisons of the theoretical results to measurements for analyzed bearing system.

Sign in / Sign up

Export Citation Format

Share Document