Heat treatment of quality low-alloy steels for KamAZ truck side members

Temperbead welding is common practice in the nuclear power industry for in-situ repair of quenched and tempered low alloy steels where post weld heat treatment is impractical. The temperbead process controls the heat input such that the weld heat-affected-zone (HAZ) in the low alloy steel is tempered by the welding heat of subsequent layers. This tempering eliminates the need for post weld heat treatment (PWHT). Unfortunately, repair organizations in the nuclear power industry are experiencing difficulty when attempting to qualify temperbead welding procedures on new quenched and tempered low alloy steel base materials manufactured to modern melting and deoxidation practices. The current ASME Code methodology and protocol for verification of adequate fracture toughness in materials was developed in the early 1970s. This paper reviews typical temperbead qualification results for vintage heats of quenched and tempered low alloy steels and compares them to similar test results obtained with modern materials of the same specification exhibiting superior fracture toughness.

Download Full-text

The role of heat treatment on wear behavior of powder metallurgy low alloy steels

Materials & Design (1980-2015) ◽

10.1016/s0261-3069(02)00046-8 ◽

2002 ◽

Vol 23 (7) ◽

pp. 667-670 ◽

Cited By ~ 41

Author(s):

H Khorsand ◽

S.M Habibi ◽

H Yoozbashizadea ◽

K Janghorban ◽

S.M.S Reihani ◽

...

Keyword(s):

Heat Treatment ◽

Powder Metallurgy ◽

Wear Behavior ◽

Low Alloy Steels ◽

Alloy Steels

Download Full-text

The heat-treatment of low-alloy steels

Metallurgical Reviews ◽

10.1179/mtlr.1968.13.1.145 ◽

1968 ◽

Vol 13 (1) ◽

pp. 145-170

Author(s):

W. E. Duckworth

Keyword(s):

Heat Treatment ◽

Low Alloy Steels ◽

Alloy Steels

Download Full-text

Mechanoelectrical heat treatment of low-alloy steels with 0.3?0.6% C

Metal Science and Heat Treatment ◽

10.1007/bf01152400 ◽

1995 ◽

Vol 37 (3) ◽

pp. 126-128

Author(s):

I. Dlougi ◽

P. Mihalichka ◽

I. Shkarek ◽

Yu. A. Garasim ◽

S. P. Oshkaderov

Keyword(s):

Heat Treatment ◽

Low Alloy Steels ◽

Alloy Steels

Download Full-text

Study Deformability Ecological Steel (41Cr4)

Materiale Plastice ◽

10.37358/mp.18.3.5029 ◽

2018 ◽

Vol 55 (3) ◽

pp. 357-360

Author(s):

Carmen Otilia Rusanescu ◽

Marin Rusanescu ◽

Florina Violeta Anghelina ◽

Ileana Nicoleta Popescu

Keyword(s):

Heat Treatment ◽

Plastic Deformation ◽

Minimum Degree ◽

Low Alloy Steels ◽

Continuous Cast ◽

External Market ◽

Degree Of Deformation ◽

Resistance To Deformation ◽

Alloy Steels ◽

Low Alloyed Steel

In this paper is studied the hot plastic deformability (plasticity and resistance to deformation) for the low-alloyed steel of heat treatment for mechanical engineering in two ways: compression and tension. Groups of low alloy steels is very important in terms of quality and quantity, the products of these steels have developed internal and external market. The plasticity variation were plotted with the temperature and it was established that the plasticity of the steel increases in the range 700-12000C, then decreases as a result of the firing of the grain boundaries, for the bars obtained from ingot and continuous cast blown it was noticed that the plasticity values are very close. Deformation resistance decreases as the temperature increases. The finest granulation was obtained for a final plastic deformation temperature of 8000C and a minimum degree of deformation of 45%.

Download Full-text