Reduction in chemical microinhomogeneity with rapid quenching of maraging steel

1990 ◽  
Vol 32 (3) ◽  
pp. 186-192
Author(s):  
T. A. Chernyshova ◽  
T. V. Lyul'kina ◽  
R. Sh. Kikaleishvili ◽  
Z. Sh. Kherodinashvili ◽  
V. P. Domukhovskii
Keyword(s):  
Maraging Steel ◽  
Rapid Quenching

TEM studies of amorphization processes and amorphous structures

1988 ◽  
Vol 46 ◽  
pp. 448-449
Author(s):  
T. E. Mitchell ◽  
R. B. Schwarz
Keyword(s):  
Amorphous Materials ◽  
Fission Products ◽  
Rapid Quenching ◽  
Surface Films ◽  
List Type ◽  
Oxide Glasses ◽  
Crystalline Materials ◽  
Amorphous Structures ◽  
Amorphous Surface ◽  
Interfacial Films

Traditional oxide glasses occur naturally as obsidian and can be made easily by suitable cooling histories. In the past 30 years, a variety of techniques have been discovered which amorphize normally crystalline materials such as metals. These include [1-3]:Rapid quenching from the vapor phase.Rapid quenching from the liquid phase.Electrodeposition of certain alloys, e.g. Fe-P.Oxidation of crystals to produce amorphous surface oxide layers.Interdiffusion of two pure crystalline metals.Hydrogen-induced vitrification of an intermetal1ic.Mechanical alloying and ball-milling of intermetal lie compounds.Irradiation processes of all kinds using ions, electrons, neutrons, and fission products.We offer here some general comments on the use of TEM to study these materials and give some particular examples of such studies.Thin specimens can be prepared from bulk homogeneous materials in the usual way. Most often, however, amorphous materials are in the form of surface films or interfacial films with different chemistry from the substrates.

TEM study of amorphization of Cu and Ti foils by cold-rolling

1990 ◽  
Vol 48 (4) ◽  
pp. 146-147
Author(s):  
W. A. Chiou ◽  
N. L. Jeon ◽  
Genbao Xu ◽  
M. Meshii
Keyword(s):  
Solid State ◽  
Cold Rolling ◽  
High Energy ◽  
Rapid Quenching ◽  
Vapor Condensation ◽  
Metallic Alloys ◽  
Solid State Reactions ◽  
High Energy Particle ◽  
Amorphous Metallic Alloys ◽  
Thin Foils

For many years amorphous metallic alloys have been prepared by rapid quenching techniques such as vapor condensation or melt quenching. Recently, solid-state reactions have shown to be an alternative for synthesizing amorphous metallic alloys. While solid-state amorphization by ball milling and high energy particle irradiation have been investigated extensively, the growth of amorphous phase by cold-rolling has been limited. This paper presents a morphological and structural study of amorphization of Cu and Ti foils by rolling.Samples of high purity Cu (99.999%) and Ti (99.99%) foils with a thickness of 0.025 mm were used as starting materials. These thin foils were cut to 5 cm (w) × 10 cm (1), and the surface was cleaned with acetone. A total of twenty alternatively stacked Cu and Ti foils were then rolled. Composite layers following each rolling pass were cleaned with acetone, cut into half and stacked together, and then rolled again.

Microstructure of resistance spot welding of maraging steels

1990 ◽  
Vol 48 (4) ◽  
pp. 900-901
Author(s):  
I. Neuman ◽  
S.F. Dirnfeld ◽  
I. Minkoff
Keyword(s):  
Maraging Steel ◽  
Spot Welding ◽  
Lath Martensite ◽  
Base Material ◽  
Aging Treatment ◽  
High Strength ◽  
Maraging Steels ◽  
Heat Treated ◽  
Current Cycle ◽  
Welding Processes

Experimental work on the spot welding of Maraging Steels revealed a surprisingly low level of strength - both in the as welded and in aged conditions. This appeared unusual since in the welding of these materials by other welding processes (TIG,MIG) the strength level is almost that of the base material. The maraging steel C250 investigated had the composition: 18wt%Ni, 8wt%Co, 5wt%Mo and additions of Al and Ti. It has a nominal tensile strength of 250 KSI. The heat treated structure of maraging steel is lath martensite the final high strength is reached by aging treatment at 485°C for 3-4 hours. During the aging process precipitation takes place of Ni3Mo and Ni3Ti and an ordered solid solution containing Co is formed.Three types of spot welding cycles were investigated: multi-pulse current cycle, bi-pulse cycle and single pulsle cycle. TIG welded samples were also tested for comparison.The microstructure investigations were carried out by SEM and EDS as well as by fractography. For multicycle spot welded maraging C250 (without aging), the dendrites start from the fusion line towards the nugget centre with an epitaxial growth region of various widths, as seen in Figure 1.

Microstructure of mechanically alloyed and hot-pressed Al5CuZr2

1990 ◽  
Vol 48 (4) ◽  
pp. 970-971
Author(s):  
T. E. Mitchell ◽  
P. B. Desch ◽  
R. B. Schwarz
Keyword(s):  
Mechanical Alloying ◽  
Vickers Hardness ◽  
Hot Pressing ◽  
Rapid Quenching ◽  
Hardened Steel ◽  
Alloyed Powder ◽  
Ion Milling ◽  
Mechanical Grinding ◽  
Mechanically Alloyed ◽  
Steel Container

Al3Zr has the highest melting temperature (1580°C) among the tri-aluminide intermetal1ics. When prepared by casting, Al3Zr forms in the tetragonal DO23 structure but by rapid quenching or by mechanical alloying (MA) it can also be prepared in the metastable cubic L12 structure. The L12 structure can be stabilized to at least 1300°C by the addition of copper and other elements. We report a TEM study of the microstructure of bulk Al5CuZr2 prepared by hot pressing mechanically alloyed powder.MA was performed in a Spex 800 mixer using a hardened steel container and balls and adding hexane as a surfactant. Between 1.4 and 2.4 wt.% of the hexane decomposed during MA and was incorporated into the alloy. The mechanically alloyed powders were degassed in vacuum at 900°C. They were compacted in a ram press at 900°C into fully dense samples having Vickers hardness of 1025. TEM specimens were prepared by mechanical grinding followed by ion milling at 120 K. TEM was performed on a Philips CM30 at 300kV.

INFLUENCE OF RAPID QUENCHING AND SAMPLE TREATMENT ON THE STRUCTURE OF MELT SPUN Al-Si ALLOYS

1985 ◽  
Vol 46 (C8) ◽  
pp. C8-533-C8-537
Author(s):  
J. Chevrier ◽  
P. Sainfort ◽  
P. Germi ◽  
D. Pavuna
Keyword(s):  
Rapid Quenching ◽  
Sample Treatment ◽  
Melt Spun

RAPID QUENCHING OF MELTS IN THE SYSTEM ZrO2-SiO2-Al2O3

1986 ◽  
Vol 47 (C1) ◽  
pp. C1-473-C1-477
Author(s):  
M. YOSHIMURA ◽  
M. KANEKO ◽  
S. SŌMIYA
Keyword(s):  
Rapid Quenching
Sign in / Sign up

Export Citation Format

Share Document