Character of the variation in certain properties of 1Cr18Ni9Ti steel under long-term loading conditions at elevated temperatures

1971 ◽  
Vol 4 (4) ◽  
pp. 346-350 ◽  
Author(s):  
G. G. Maksimovich
Keyword(s):  
Elevated Temperatures ◽  
Loading Conditions ◽  
1Cr18ni9ti Steel

scholarly journals CO Detection Investigation at High Temperature by SiC MISFET Metal/Oxide Gas Sensors

Proceedings ◽  
2021 ◽  
Vol 56 (1) ◽  
pp. 41
Author(s):  
Lida Khajavizadeh ◽  
Anita Lloyd Spetz ◽  
Mike Andersson
Keyword(s):  
High Temperature ◽  
Gas Sensors ◽  
Elevated Temperatures ◽  
Long Term Stability ◽  
Stability Performance ◽  
Catalytic Metal ◽  
Co Detection ◽  
Effect Transistor ◽  
Metal Oxide Gas Sensors

In order to investigate the necessary device improvements for high-temperature CO sensing with SiC metal insulator semiconductor field effect transistor (MISFET)-based chemical gas sensors, devices employing, as the gas-sensitive gate contact, a film of co-deposited Pt/Al2O3 instead of the commonly used catalytic metal-based contacts were fabricated and characterized for CO detection at elevated temperatures and different CO and O2 levels. It can be concluded that the sensing mechanism at elevated temperatures correlates with oxygen removal from the sensor surface rather than the surface CO coverage as observed at lower temperatures. The long-term stability performance was also shown to be improved compared to that of previously studied devices.

Technology Focus: Wellbore Tubulars (July 2021)

2021 ◽  
Vol 73 (07) ◽  
pp. 50-50
Author(s):  
Robello Samuel
Keyword(s):  
Geothermal Energy ◽  
Elevated Temperatures ◽  
Clean Energy ◽  
Well Integrity ◽  
The Future ◽  
Geothermal Wells ◽  
Abandoned Wells ◽  
Thermal Simulations ◽  
Technology Focus

How we think about the future of the pipe industry must evolve. How must tubular design and manufacturing change as we transition to clean energy? Geothermal energy is an area that needs attention and, further, needs very specific attention on tubulars. Tubulars are an important component in the construction of geothermal wells, and we must align our requirements for geothermal energy. Some of the main challenges encountered in geothermal wells are corrosion and scaling. Moreover, temperature becomes a major consideration for tubulars, even more so with the temperature excursion during geothermal production. Perhaps the critical aspect in the design of the geothermal wells involves casing selection and design. Beyond manufacturing casing pipes to withstand these problems, considering the manufacturing of other components, such as connections, float collars, and float shoes, also is essential. Thermal expansion and thermal excursion of casings are well-integrity concerns; thus, casing design is important for long-term sustainability of geothermal wells. Apart from thermal simulations, guidelines and software are needed to undergird the designs to withstand not only temperature excursions but also thermomechanical and thermochemical loadings. Engineered nonmetallic casings also provide an alternative solution because they provide the desired strength and corrosion resistance in addition to meeting the goals of sustainability. Undoubtedly, the future of the tubular industry is going to be revitalized. The question now is how we can retrofit existing abandoned wells for this purpose. Recommended additional reading at OnePetro: www.onepetro.org. SPE 199570 - Special Considerations for Well-Tubular Design at Elevated Temperatures by Gang Tao, C-FER Technologies, et al.

Rational Design of Organic Electro-Optic Materials

2001 ◽  
Vol 708 ◽  
Author(s):  
Alex Jen ◽  
Robert Neilsen ◽  
Bruce Robinson ◽  
William H. Steier ◽  
Larry Dalton
Keyword(s):  
Wavelength Division Multiplexing ◽  
Material Properties ◽  
Electrostatic Interactions ◽  
Rational Design ◽  
Elevated Temperatures ◽  
Optical Loss ◽  
Quality Factors ◽  
Electro Optic ◽  
Lattice Hardening

ABSTRACTA number of material properties must be optimized before organic electro-optic materials can be used for practical device applications. These include electro-optic activity, optical transparency, and stability including both thermal and photochemical stability. Exploiting an improved understanding of the structure/function relationships, we have recently prepared materials exhibiting electro-optic coefficients of greater than 50 pm/V and optical loss values of less than 0.7 dB/cm at the telecommunication wavelengths of 1.3 and 1.55 microns. When oxygen is excluded to a reasonable extent, long-term photostability to optical power levels of 20 mW has been observed. Photostability is further improved by addition of scavengers and by lattice hardening. Long-term (greater than 1000 hours) thermal stability of poling-induced electro-optic activity is also observed at elevated temperatures (greater than 80°C) when appropriate lattice hardening is used. The successful improvement of organic electro-optic materials rests upon (1) attention to the design of chromophore structure including design to inhibit unwanted intermolecular electrostatic interactions and to improve chromophore instability and (2) attention to processing conditions including those involved in spin casting, electric field poling, and lattice hardening. A particularly attractive new direction has been the exploitation of dendrimer structures and particularly of multi-chromophore containing dendrimer structures. This approach has permitted the simultaneous improvement of all material properties. Development of new materials has facilitated the fabrication of a number of prototype devices and most recently has permitted investigation of the incorporation of electro-optic materials into photonic bandgap and microresonator structures. The latter are relevant to active wavelength division multiplexing (WDM). Significant quality factors (greater than 10,000) have been realized for such devices permitting wavelength discrimination at telecommunication wavelengths of 0.01 nm.

scholarly journals High–flux Composite PTMSP Membranes with Long–term Stable Characteristics at Elevated Temperatures and Pressures

2012 ◽  
Vol 44 ◽  
pp. 782-783 ◽  
Author(s):  
G. Dibrov ◽  
E. Novitskii ◽  
V. Vasilevskii ◽  
S. Bazhenov ◽  
V. Volkov
Keyword(s):  
Elevated Temperatures ◽  
High Flux

Long-Term Stability of Aluminum Oxide Based Surface Passivation Schemes Under Illumination at Elevated Temperatures

2017 ◽  
Vol 7 (5) ◽  
pp. 1197-1202 ◽  
Author(s):  
Tim Niewelt ◽  
Wolfram Kwapil ◽  
Marisa Selinger ◽  
Armin Richter ◽  
Martin C. Schubert
Keyword(s):  
Aluminum Oxide ◽  
Elevated Temperatures ◽  
Surface Passivation ◽  
Term Stability ◽  
Long Term Stability

Comparison of femur strain under different loading scenarios: Experimental testing

2020 ◽  
Vol 235 (1) ◽  
pp. 17-27
Author(s):  
Ievgen Levadnyi ◽  
Jan Awrejcewicz ◽  
Yan Zhang ◽  
Yaodong Gu
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Strain Distribution ◽  
Element Model ◽  
Surface Strain ◽  
Image Correlation ◽  
Loading Conditions ◽  
Bone Implant ◽  
Bone Stiffness

Bone fracture, formation and adaptation are related to mechanical strains in bone. Assessing bone stiffness and strain distribution under different loading conditions may help predict diseases and improve surgical results by determining the best conditions for long-term functioning of bone-implant systems. In this study, an experimentally wide range of loading conditions (56) was used to cover the directional range spanned by the hip joint force. Loads for different stance configurations were applied to composite femurs and assessed in a material testing machine. The experimental analysis provides a better understanding of the influence of the bone inclination angle in the frontal and sagittal planes on strain distribution and stiffness. The results show that the surface strain magnitude and stiffness vary significantly under different loading conditions. For the axial compression, maximal bending is observed at the mid-shaft, and bone stiffness is also maximal. The increased inclination leads to decreased stiffness and increased magnitude of maximum strain at the distal end of the femur. For comparative analysis of results, a three-dimensional, finite element model of the femur was used. To validate the finite element model, strain gauges and digital image correlation system were employed. During validation of the model, regression analysis indicated robust agreement between the measured and predicted strains, with high correlation coefficient and low root-mean-square error of the estimate. The results of stiffnesses obtained from multi-loading conditions experiments were qualitatively compared with results obtained from a finite element analysis of the validated model of femur with the same multi-loading conditions. When the obtained numerical results are qualitatively compared with experimental ones, similarities can be noted. The developed finite element model of femur may be used as a promising tool to estimate proximal femur strength and identify the best conditions for long-term functioning of the bone-implant system in future study.

Long-Term Evaluation of the Bonding Strength of Composite Repairs

2012 ◽  
Author(s):  
Khalid Farrag ◽  
Kevin Stutenberg
Keyword(s):  
Shear Strength ◽  
Elevated Temperatures ◽  
Water Solution ◽  
Effect Of Temperature ◽  
Shear Tests ◽  
Composite Repair ◽  
Testing Program ◽  
Repair Systems ◽  
Composite Repairs

The long-term performance of composite repair systems depends on their structural integrity and interaction with the carrier pipe. The adhesives used in the composites are critical components that not only bond the repair to the pipe, but also bond the individual layers of the repair to one another. The durability of the inter-laminate adhesive bond is required to ensure adequate load transfer between the pipe and the composite layers over the predicted lifetime of the repair. A testing program was performed to evaluate the shear strength of the adhesives used in composite repairs. The testing program evaluated the performance of seven commercially-available composite repair systems and it consisted of short-term and long-term shear tests on the adhesives and cathodic disbondment tests on the repair systems. The long-term shear tests were performed for 10,000 hours on samples submerged in a water solution with pH value of 9 and at various loading levels at temperatures of 70°F, 105°F and 140°F. The results of the long-term tests at elevated temperatures were extrapolated to predict the shear strengths at longer durations. The 20-year shear strengths of the composites were estimated using: (a) direct extrapolation of the best-fit curves and (b) the application of the rate process procedure. The results demonstrated the significant effect of temperature on the bond strength of the composites and provided a comparative analysis to evaluate the long-term shear strength and cathodic disbondment of the composite repair systems.

PRESERVATION OF FOSSIL MICROBES AND BIOFILM IN CAVE POOL CARBONATES AND COMPARISON TO OTHER MICROBIAL CARBONATE ENVIRONMENTS

Palaios ◽  
2016 ◽  
Vol 31 (4) ◽  
pp. 177-189 ◽  
Author(s):  
LESLIE A. MELIM ◽  
DIANA E. NORTHUP ◽  
PENELOPE J. BOSTON ◽  
MICHAEL N. SPILDE
Keyword(s):  
Organic Material ◽  
Elevated Temperatures ◽  
Hot Spring ◽  
Cold Seep ◽  
Alternative Mode ◽  
Photolytic Degradation ◽  
Microbial Carbonate ◽  
Edx Analyses ◽  
Uniform Diameter

Abstract Fossil microbes are generally preserved by authigenic minerals, including silica, apatite, iron minerals, clays, and carbonates. An alternative mode of preservation by entombment in calcite, without replacement, has been identified in carbonate cave pool microbialites that were etched and examined in the scanning electron microscope (SEM). Features identified include filaments, threads, and films that show excess carbon in energy dispersive X-ray (EDX) analyses, suggesting preservation of organic matter. Filaments are single smooth or reticulated strands with curving string-like morphology, often hollow, and with a uniform diameter of 0.5 to 1.0 μm. Threads, in contrast, are variable thickness, from several microns down to 0.1 μm, always solid, and commonly branch. Films are thin (< 1 μm) drapes associated with threads. Filaments are interpreted as microbial filaments, while threads and films are interpreted as preserved extracellular polymeric substance (EPS). In addition, microbial filaments and EPS are only revealed via acid etching, suggesting preservation of organic material by entombment, not by replacement with calcite. To determine whether entombed microbes are a common feature of carbonate microbialites that form in different environmental settings, samples of hot spring travertine, caliche soil, and reef microbialite were examined. Whereas the travertine samples were barren, entombed EPS was found in the caliche soil and the reef microbialite; the latter also contained a few entombed filaments. In addition, entombed microbial material has been reported from carbonate cold seep deposits. Such findings indicate that entombment of microbes and EPS in carbonates is not restricted to cave settings, but is more widespread than previously reported. Possible causes for the lack of preservation in travertines include rapid degradation of microbial material either by sunlight due to photolytic degradation, aerobic microbial degradation, detritivore consumption, or elevated temperatures. Rapid carbonate precipitation is ruled out as, somewhat surprisingly, preservation is better in slower growing cave carbonates than in rapidly growing travertines. Potential long-term preservation of organic material entombed in carbonate has implications for the characterization of fossil microbial communities using molecular biomarkers and the search for life on other planets.

scholarly journals Brazing Strategies for High Temperature Ultrasonic Transducers Based on LiNbO3 Piezoelectric Elements

Instruments ◽  
2018 ◽  
Vol 3 (1) ◽  
pp. 2 ◽  
Author(s):  
Christopher Bosyj ◽  
Neelesh Bhadwal ◽  
Thomas Coyle ◽  
Anthony Sinclair
Keyword(s):  
High Temperature ◽  
Lithium Niobate ◽  
Elevated Temperatures ◽  
Piezoelectric Element ◽  
Low Noise ◽  
Ultrasonic Transducers ◽  
Acoustic Coupling ◽  
Industrial Operations ◽  
Critical Components

Long-term installation of ultrasonic transducers in high temperature environments allows for continuous monitoring of critical components and processes without the need to halt industrial operations. Transducer designs based on the high-Curie-point piezoelectric material lithium niobate have been shown to both be effective and stable at extreme temperatures for long-term installation. In this study, several brazing techniques are evaluated, all of which aim to provide both mechanical bonding and acoustic coupling directly to a bare lithium niobate piezoelectric element. Two brazing materials—a novel silver-copper braze applied in a reactive air environment and an aluminum-based braze applied in a vacuum environment—are found to be suitable for ultrasound transmission at elevated temperatures. Reliable wide-bandwidth and low-noise ultrasound transmission is achieved between room temperature and 800 °C.

Sign in / Sign up

Export Citation Format

Share Document