FORCED RESPONSE ANALYSIS IN TIME AND FREQUENCY DOMAINS OF A TUNED BLADED DISK WITH FRICTION DAMPERS

1998 ◽  
Vol 214 (3) ◽  
pp. 395-412 ◽  
Author(s):  
G. Csaba
Keyword(s):  
Forced Response ◽  
Response Analysis ◽  
Friction Dampers ◽  
Bladed Disk ◽  
Frequency Domains ◽  
Time And Frequency Domains

Explicit Finite Element Models of Friction Dampers in Forced Response Analysis of Bladed Discs

2007 ◽  
Author(s):  
E. P. Petrov
Keyword(s):  
Finite Element ◽  
Large Scale ◽  
Dynamic Properties ◽  
Forced Response ◽  
Response Analysis ◽  
Contact Interactions ◽  
Contact Interface ◽  
Explicit Finite Element ◽  
Friction Dampers ◽  
Time Dynamic

A generic method for analysis of nonlinear forced response for bladed discs with friction dampers of different design has been developed. The method uses explicit finite element modelling of dampers, which allows accurate description of flexibility and, for the first time, dynamic properties of dampers of different design in multiharmonic analysis of bladed discs. Large-scale finite element damper and bladed disc models containing 104–106 DOFs can be used. These models, together with detailed description of contact interactions over contact interface areas, allow for any level of refinement required for modelling of elastic damper bodies and for modelling of friction contact interactions. Numerical studies of realistic bladed discs have been performed with three different types of underplatform dampers: (i) a ‘cottage-roof’ (called also ‘wedge’) damper; (ii) seal wire damper; and (iii) a strip damper. Effects of contact interface parameters and excitation levels on damping properties of the dampers and forced response are extensively explored.

Investigation of Damping Potential of Strip Damper on a Real Turbine Blade

2016 ◽  
Author(s):  
M. Afzal ◽  
I. Lopez Arteaga ◽  
L. Kari ◽  
V. Kharyton
Keyword(s):  
Boundary Conditions ◽  
Dynamic Properties ◽  
Equations Of Motion ◽  
Iterative Solution ◽  
Element Model ◽  
Forced Response ◽  
Contact Forces ◽  
Response Analysis ◽  
Bladed Disk ◽  
Different Types

This paper investigates the damping potential of strip dampers on a real turbine bladed disk. A 3D numerical friction contact model is used to compute the contact forces by means of the Alternate Frequency Time domain method. The Jacobian matrix required during the iterative solution is computed in parallel with the contact forces, by a quasi-analytical method. A finite element model of the strip dampers, that allows for an accurate description of their dynamic properties, is included in the steady-state forced response analysis of the bladed disk. Cyclic symmetry boundary conditions and the multiharmonic balance method are applied in the formulation of the equations of motion in the frequency domain. The nonlinear forced response analysis is performed with two different types of boundary conditions on the strip: (a) free-free and (b) elastic, and their influence is analyzed. The effect of the strip mass, thickness and the excitation levels on the forced response curve is investigated in detail.

The Interaction Between Mistuning and Friction in the Forced Response of Bladed Disk Assemblies

1985 ◽  
Vol 107 (1) ◽  
pp. 205-211 ◽  
Author(s):  
J. H. Griffin ◽  
A. Sinha
Keyword(s):  
Gas Turbine ◽  
Turbine Blades ◽  
Forced Response ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Resonant Response ◽  
Friction Dampers ◽  
Bladed Disk ◽  
The Impact ◽  
Slip Force

This paper summarizes the results of an investigation to establish the impact of mistuning on the performance and design of blade-to-blade friction dampers of the type used to control the resonant response of turbine blades in gas turbine engines. In addition, it discusses the importance of friction slip force variations on the dynamic response of shrouded fan blades.

Transient Forced Response Analysis of Mistuned Steam Turbine Blades During Startup and Coastdown

2016 ◽  
Vol 139 (1) ◽  
Author(s):  
Christian Siewert ◽  
Heinrich Stüer
Keyword(s):  
Mechanical Model ◽  
Turbine Blades ◽  
Forced Vibrations ◽  
Forced Response ◽  
The Self ◽  
Response Analysis ◽  
Computationally Efficient ◽  
Bladed Disk ◽  
Steam Turbine Blades ◽  
Number Of Publications

It is well known that the vibrational behavior of a mistuned bladed disk differs strongly from that of a tuned bladed disk. A large number of publications dealing with the dynamics of mistuned bladed disks are available in the literature. The vibrational phenomena analyzed in these publications are either forced vibrations or self-excited flutter vibrations. Nearly, all published literature on the forced vibrations of mistuned blades disks considers harmonic, i.e., steady-state, vibrations, whereas the self-excited flutter vibrations are analyzed by the evaluation of the margin against instabilities by means of a modal, or rather than eigenvalue, analysis. The transient forced response of mistuned bladed disk is not analyzed in detail so far. In this paper, a computationally efficient mechanical model of a mistuned bladed disk to compute the transient forced response is presented. This model is based on the well-known fundamental model of mistuning (FMM). With this model, the statistics of the transient forced response of a mistuned bladed disk is analyzed and compared to the results of harmonic forced response analysis.

Experimental and Numerical Investigation of Rotating Bladed Disk Forced Response Using Underplatform Friction Dampers

2008 ◽  
Vol 130 (4) ◽  
Author(s):  
Ibrahim A. Sever ◽  
Evgeny P. Petrov ◽  
David J. Ewins
Keyword(s):  
Measurement Techniques ◽  
Measured Data ◽  
Forced Response ◽  
Imperial College ◽  
Test Rig ◽  
Response Curves ◽  
Friction Dampers ◽  
Bladed Disk ◽  
Prediction Tools ◽  
Numerical Predictions

In this paper, we present a methodology and results from an experimental investigation of forced vibration response for a bladed disk with fitted underplatform “cottage-roof” friction dampers, together with the corresponding numerical predictions. A carefully designed and constructed rotating test rig is used to make precise measurements, which involve only the phenomena of interest. For this purpose, the measurement rig is operated under vacuum to eliminate aerodynamic effects on the rotating blisk and noncontact excitation and measurement techniques are employed so as not to modify the bladed disk dynamics. The experimental data measured are used for validation of multiharmonic balance-based prediction tools developed at the Imperial College. Predictions are carried out both with and without taking inherent mechanical mistuning into account, which is identified from measured data. Measured and predicted response curves are compared with each other and the degree of correlation is discussed.

Transient Forced Response Analysis of Mistuned Steam Turbine Blades During Start-Up and Coast-Down

2014 ◽  
Author(s):  
Christian Siewert ◽  
Heinrich Stüer
Keyword(s):  
Mechanical Model ◽  
Turbine Blades ◽  
Forced Vibrations ◽  
Forced Response ◽  
Response Analysis ◽  
Computationally Efficient ◽  
Bladed Disk ◽  
Start Up ◽  
Steam Turbine Blades ◽  
Number Of Publications

It is well-known that the vibrational behavior of a mistuned bladed disk differs strongly from that of a tuned bladed disk. A large number of publications dealing with the dynamics of mistuned bladed disks is available in the literature. The vibrational phenomena analyzed in these publications are either forced vibrations or self-excited flutter vibrations. Nearly all published literature on the forced vibrations of mistuned blades disks considers harmonic, i. e. steady-state, vibrations, whereas the self-excited flutter vibrations are analyzed by the evaluation of the margin against instabilities by means of a modal, or rather than eigenvalue, analysis. The transient forced response of mistuned bladed disk is not analyzed in detail so far. In this paper, a computationally efficient mechanical model of a mistuned bladed disk to compute the transient forced response is presented. This model is based on the well-known Fundamental Model of Mistuning. With this model, the statistics of the transient forced response of a mistuned bladed disk is analyzed and compared to the results of harmonic forced response analysis.

scholarly journals Vibrational Response Analysis of Mistuned Bladed Disk System of Grouped Blades

1998 ◽  
Author(s):  
Y. Kaneko ◽  
K. Mori ◽  
H. Ohyama ◽  
E. Watanabe
Keyword(s):  
Synthesis Method ◽  
Forced Response ◽  
Response Analysis ◽  
Analysis Method ◽  
Disk System ◽  
Vibrational Response ◽  
Bladed Disk ◽  
System A ◽  
Vibrational Characteristics ◽  
Grouped Blades

For the purpose of the efficient analysis of a mistuned bladed disk system, a new analysis method which applies the substructure synthesis method and the modal analysis method is proposed. Using the proposed method, the vibrational characteristics of the grouped blades structure are studied. From the results, it is found that the grouped blades structure is very sensitive to the mistuning. It is also found that the mixed grouped blades structure (a bladed disk system consisting of some different types of grouped blades relating to the number of blades contained) has an undesirable effect on the forced response. Moreover, by comparing the vibrational characteristics of the integral shroud blades (ISB) structure with those of the grouped blades structure, it is clarified that the reliability of the ISB structure is superior to other structures also from the viewpoint of the mistuning.

scholarly journals Test-Model Correlation of Dry-Friction Damping Phenomena in Aero-Engines

2008 ◽  
Author(s):  
P. Jean ◽  
C. Gibert ◽  
C. Dupont ◽  
J.-P. Lombard
Keyword(s):  
Dry Friction ◽  
Forced Response ◽  
Test Model ◽  
Friction Damping ◽  
Bladed Disks ◽  
Friction Dampers ◽  
Bladed Disk ◽  
Resonance Frequencies ◽  
Non Linear ◽  
Aero Engines

In order to control the risk of high cycle fatigue of bladed disks, it is important to predict precisely the vibration levels and to design damping solutions to attenuate them. Therefore, Snecma has made some efforts in the last years in order to characterize better the damping in aero-engines. Among the various damping sources, friction damping is particularly difficult to model due to its non-linear behaviour [1]. For that purpose, two methods based on multi-harmonic balance strategy have been especially developed for Snecma, dedicated to the study of the non-linear forced response of bladed disks. The first one enables to model the bladed disk equipped with dry-friction dampers [2], and the second one takes into account intrinsic friction located in disk-blade interface [3]. To validate both models experimentally, a test campaign has been carried out in a vacuum chamber on a rotating bladed disk excited by piezoelectric actuators. The blade shanks have been softened in order to increase friction effects. Experimental results show a regular and reproducible behaviour of the non-linear forced response, over various rotation speed and excitation levels. The contributions of friction dampers and friction in blade attachment have been decoupled thanks to glue applied in the blade root. Both friction phenomena that were observed experimentally at resonance of the blade first bending mode have been reproduced numerically. After updating modeling parameters, an acceptable correlation was found on resonance frequencies, amplitudes and damping levels over the full experimental setup range, which validates these numerical tools for their use in design process.

Explicit Finite Element Models of Friction Dampers in Forced Response Analysis of Bladed Disks

2008 ◽  
Vol 130 (2) ◽  
Author(s):  
E. P. Petrov
Keyword(s):  
Finite Element ◽  
Large Scale ◽  
Dynamic Properties ◽  
Forced Response ◽  
Response Analysis ◽  
Contact Interactions ◽  
Contact Interface ◽  
Bladed Disks ◽  
Explicit Finite Element ◽  
Friction Dampers

A generic method for analysis of nonlinear forced response for bladed disks with friction dampers of different designs has been developed. The method uses explicit finite element modeling of dampers, which allows accurate description of flexibility and, for the first time, dynamic properties of dampers of different designs in multiharmonic analysis of bladed disks. Large-scale finite element damper and bladed disk models containing 104−106 degrees of freedom can be used. These models, together with detailed description of contact interactions over contact interface areas, allow for any level of refinement required for modeling of elastic damper bodies and for modeling of friction contact interactions. Numerical studies of realistic bladed disks have been performed with three different types of underplatform dampers: (i) a “cottage-roof” (also called “wedge”) damper, (ii) seal wire damper, and (iii) a strip damper. Effects of contact interface parameters and excitation levels on damping properties of the dampers and forced response are extensively explored.

Sign in / Sign up

Export Citation Format

Share Document