Variability of breaking wave characteristics and impact loads on offshore wind turbines supported by monopiles

Wind Energy ◽  
2015 ◽  
Vol 19 (2) ◽  
pp. 301-312 ◽  
Author(s):  
S. Hallowell ◽  
A. T. Myers ◽  
S. R. Arwade
Keyword(s):  
Wind Turbines ◽  
Offshore Wind ◽  
Breaking Wave ◽  
Impact Loads ◽  
Offshore Wind Turbines ◽  
Wave Characteristics

Detailed Study on Breaking Wave Interactions With a Jacket Structure Based on Experimental Investigations

2017 ◽  
Vol 140 (2) ◽  
Author(s):  
Jithin Jose ◽  
Olga Podrażka ◽  
Ove Tobias Gudmestad ◽  
Witold Cieślikiewicz
Keyword(s):  
Wind Turbines ◽  
Wave Breaking ◽  
Offshore Structures ◽  
Offshore Wind ◽  
Wave Forces ◽  
Breaking Wave ◽  
Offshore Wind Turbines ◽  
Wave Parameters ◽  
Wave Slamming ◽  
Breaking Wave Forces

Wave breaking is one of the major concerns for offshore structures installed in shallow waters. Impulsive breaking wave forces sometimes govern the design of such structures, particularly in areas with a sloping sea bottom. Most of the existing offshore wind turbines were installed in shallow water regions. Among fixed-type support structures for offshore wind turbines, jacket structures have become popular in recent times as the water depth for fixed offshore wind structures increases. However, there are many uncertainties in estimating breaking wave forces on a jacket structure, as only a limited number of past studies have estimated these forces. Present study is based on the WaveSlam experiment carried out in 2013, in which a jacket structure of 1:8 scale was tested for several breaking wave conditions. The total and local wave slamming forces are obtained from the experimental measured forces, using two different filtering methods. The total wave slamming forces are filtered from the measured forces using the empirical mode decomposition (EMD) method, and local slamming forces are obtained by the frequency response function (FRF) method. From these results, the peak slamming forces and slamming coefficients on the jacket members are estimated. The breaking wave forces are found to be dependent on various breaking wave parameters such as breaking wave height, wave period, wave front asymmetry, and wave-breaking positions. These wave parameters are estimated from the wave gauge measurements taken during the experiment. The dependency of the wave slamming forces on these estimated wave parameters is also investigated.

Modeling Breaking Waves for Fixed-Bottom Support Structures for Offshore Wind Turbines

2018 ◽  
Author(s):  
Hannah M. Johlas ◽  
Spencer Hallowell ◽  
Shengbai Xie ◽  
Pedro Lomonaco ◽  
Matthew A. Lackner ◽  
...  
Keyword(s):  
Wind Turbines ◽  
Water Depth ◽  
Adaptive Mesh Refinement ◽  
Adaptive Mesh ◽  
Breaking Waves ◽  
Offshore Wind ◽  
Breaking Wave ◽  
Intermediate Water ◽  
Offshore Wind Turbines ◽  
Ocean Conditions

Fixed-bottom offshore wind turbines (OWTs) are typically located in shallow to intermediate water depth, where waves are likely to break. Support structure designs for such turbines must account for loads due to breaking waves, but predictions from breaking wave models often disagree with each other and with observed behavior. This variability indicates the need for a better understanding of each model’s strengths and limitations, especially for different ocean conditions. This work evaluates and improves the accuracy of common breaking wave criteria through comparison to Computational Fluid Dynamics (CFD) simulations of breaking waves. The simulated ocean conditions are representative of potential U.S. East Coast offshore wind energy development sites, but the discussion of model accuracy and limitations can be applied to any location with similar ocean conditions. The waves are simulated using CONVERGE, a commercial CFD software that uses a Volume of Fluid (VOF) approach and includes adaptive mesh refinement at the evolving air-water interface. First, the CFD model is validated against experimental data for shoaling and breaking wave surface elevations. Second, 2D simulations of breaking waves are compared to widely-used breaking wave limits (McCowan, Miche, and Goda) for different combinations of wave height, wavelength, water depth, and seafloor slope. Based on these comparisons, the accuracy and limitations of each breaking limit model are discussed. General usage guidelines are then recommended.

Experimental Investigations of Breaking Wave Impact Forces on a Monopile Substructure for Offshore Wind Turbines Under Regular Breaking Waves

2017 ◽  
Author(s):  
Vipin Chakkurunni Palliyalil ◽  
Panneer Selvam Rajamanickam ◽  
Mayilvahanan Alagan Chella ◽  
Vijaya Kumar Govindasamy
Keyword(s):  
Circular Cylinder ◽  
Wind Turbines ◽  
Breaking Waves ◽  
Offshore Wind ◽  
Offshore Wind Turbine ◽  
Breaking Wave ◽  
Wave Impact ◽  
Offshore Wind Turbines ◽  
Impact Forces ◽  
The Impact

The main objective of the paper is to investigate wave impact forces from breaking waves on a monopile substructure for offshore wind turbine in shallow waters. This study examines the load assessment parameters relevant for breaking wave forces on a vertical circular cylinder subjected to breaking waves. Experiments are conducted in a shallow water flume and the wave generation is based on piston type wave maker. The experiments are performed with a vertical circular cylinder with diameter, D = 0.20m which represents a monopile substructure for offshore wind turbines with regular waves of frequencies around 0.8Hz. The experimental setup consists of a 1/10 slope followed by a horizontal bed portion with a water depth of 0.8m. Plunging breaking waves are generated and free surface elevations are measured at different locations along the wave tank from wave paddle to the cylinder in order to find the breaking characteristics. Wave impact pressures are measured on the cylinder at eight different vertical positions along the height of the cylinder under breaking waves for different environmental conditions. The wave impact pressures and wave surface elevations in the vicinity of the cylinder during the impact for three different wave conditions are presented and discussed.

scholarly journals Numerical study of irregular breaking wave forces on a monopile for offshore wind turbines

2017 ◽  
Vol 137 ◽  
pp. 246-254 ◽  
Author(s):  
Ankit Aggarwal ◽  
Mayilvahanan Alagan Chella ◽  
Hans Bihs ◽  
Øivind Asgeir Arntsen
Keyword(s):  
Wind Turbines ◽  
Numerical Study ◽  
Offshore Wind ◽  
Wave Forces ◽  
Breaking Wave ◽  
Offshore Wind Turbines ◽  
Breaking Wave Forces

Pitch Angle Control of Floating Offshore Wind Turbines by H∞ Control

2014 ◽  
Vol 134 (8) ◽  
pp. 1096-1103 ◽  
Author(s):  
Sho Tsujimoto ◽  
Ségolène Dessort ◽  
Naoyuki Hara ◽  
Keiji Konishi
Keyword(s):  
Wind Turbines ◽  
Pitch Angle ◽  
Offshore Wind ◽  
Offshore Wind Turbines ◽  
Floating Offshore Wind Turbines
Sign in / Sign up

Export Citation Format

Share Document