Enhancement in the Modeling of Temperature and Strain Rate-Dependent Plastic Hardening Behavior of a Sheet Metal

2015 ◽  
Vol 86 (8) ◽  
pp. 902-914 ◽  
Author(s):  
Dohyun Leem ◽  
Hyuk-Jong Bong ◽  
Frederic Barlat ◽  
Myoung-Gyu Lee ◽  
Jung-Han Song ◽  
...  
Keyword(s):  
Strain Rate ◽  
Sheet Metal ◽  
Hardening Behavior ◽  
Rate Dependent ◽  
Plastic Hardening

A Newly Developed Clamping Device for the Tension/Compression Test at Various Strain Rates

2014 ◽  
Vol 626 ◽  
pp. 353-358
Author(s):  
Geun Su Joo ◽  
Min Kuk Choi ◽  
Hoon Huh
Keyword(s):  
Strain Rate ◽  
Sheet Metal ◽  
Metal Forming ◽  
Loading Condition ◽  
Strain Rates ◽  
Compression Tests ◽  
Compression Behavior ◽  
Compression Loading ◽  
Hardening Behavior ◽  
Clamping Device

The tension/compression hardening behavior is important in sheet metal forming processes because of complicated loading paths. Experimental methods to measure the tension/ compression behavior have not considered the effect of the strain rate although the strain rate is related to the hardening behavior of sheet metal. The tension/compression tests need to be conducted considering the strain rate to acquire accurate hardening behavior.This paper deals with an experimental technique to measure the tension/compression behavior of sheet metal at various strain rates. A new clamping device was developed to prevent a sheet specimen from buckling under compression loading condition. Compared to previous clamping devices, the clamping device was devised to uniformly impose a clamping force and easily measure the strain from side of a specimen. Tension/compression tests have been conducted at various strain rates for SPCC and DP590 with displacement of 10%. Hardening curves under the tension or compression loading condition were obtained and analyzed with respect to the strain rate.

Investigation of the Anisotropic Strain Rate Dependency of AA5182-O and DC04 for Different Stress States

2016 ◽  
Vol 1140 ◽  
pp. 35-42 ◽  
Author(s):  
Matthias Lenzen ◽  
Emanuela Affronti ◽  
Martin Rosenschon ◽  
Marion Merklein
Keyword(s):  
Strain Rate ◽  
Sheet Metal ◽  
Sheet Metal Forming ◽  
Metal Forming ◽  
Equivalent Stress ◽  
Sheet Metals ◽  
Forming Process ◽  
Rate Dependent ◽  
Material Characteristics ◽  
Deformation Velocity

A more precise numerical simulation of sheet metal forming processes leads to a demand for more detailed material characterisation. Hence, it is advisable to consider the strain rate reliant and anisotropic material characteristics. There are various common sheet metals that have beside of an anisotropic a more or less distinct strain rate dependent material behaviour. With regard to these material characteristics, for a more detailed numerical prediction of a sheet metal forming process, it is necessary to include the aspect of deformation velocity. A characterisation of the strain rate dependent hardening behaviour for the two common sheet metals DC04 and AA5182-O is performed under tensile as well as shear load and their behaviour is compared after v. Mises equivalent stress and strain. The two strain rate models from Norton-Hoff and Tanimura are calibrated on basis of the experimental data and their applicability for the investigated materials is evaluated. The calibration of the strain rate sensitive models showed for both materials a very good comparability, respectively.

Strain-rate dependent material properties of selective laser melted AlSi10Mg and AlSi3.5Mg2.5

2020 ◽  
Vol 62 (6) ◽  
pp. 573-583
Author(s):  
Andreas Lutz ◽  
Lukas Huber ◽  
Claus Emmelmann
Keyword(s):  
Strain Rate ◽  
Material Properties ◽  
Rate Dependent

Strain-Rate Dependent Deformation Behavior in WC-10 wt%Ni 3Al Cermet Micropillars Under Uniaxial Compression

2019 ◽  
Author(s):  
Minai Zhang ◽  
Xin Wang ◽  
Alexander D. Dupuy ◽  
Julie M. Schoenung ◽  
Xiaoqiang Li
Keyword(s):  
Strain Rate ◽  
Uniaxial Compression ◽  
Deformation Behavior ◽  
Rate Dependent

scholarly journals Identification of the LLDPE Constitutive Material Model for Energy Absorption in Impact Applications

Polymers ◽  
2021 ◽  
Vol 13 (10) ◽  
pp. 1537
Author(s):  
Luděk Hynčík ◽  
Petra Kochová ◽  
Jan Špička ◽  
Tomasz Bońkowski ◽  
Robert Cimrman ◽  
...  
Keyword(s):  
Strain Rate ◽  
Material Model ◽  
Low Density Polyethylene ◽  
Low Density ◽  
Linear Low Density Polyethylene ◽  
Stress Strain ◽  
Rate Dependent ◽  
Constitutive Material Model ◽  
Principal Directions ◽  
Constitutive Material

Current industrial trends bring new challenges in energy absorbing systems. Polymer materials as the traditional packaging materials seem to be promising due to their low weight, structure, and production price. Based on the review, the linear low-density polyethylene (LLDPE) material was identified as the most promising material for absorbing impact energy. The current paper addresses the identification of the material parameters and the development of a constitutive material model to be used in future designs by virtual prototyping. The paper deals with the experimental measurement of the stress-strain relations of linear low-density polyethylene under static and dynamic loading. The quasi-static measurement was realized in two perpendicular principal directions and was supplemented by a test measurement in the 45° direction, i.e., exactly between the principal directions. The quasi-static stress-strain curves were analyzed as an initial step for dynamic strain rate-dependent material behavior. The dynamic response was tested in a drop tower using a spherical impactor hitting a flat material multi-layered specimen at two different energy levels. The strain rate-dependent material model was identified by optimizing the static material response obtained in the dynamic experiments. The material model was validated by the virtual reconstruction of the experiments and by comparing the numerical results to the experimental ones.

A Modified Peric Model for Al-Mg Alloy Sheet with Rate-Independent Initial Yield Stress at Warm Temperatures

2019 ◽  
Vol 287 ◽  
pp. 3-7
Author(s):  
Yong Zhang ◽  
Qing Zhang ◽  
Yuan Tao Sun ◽  
Xian Rong Qin
Keyword(s):  
Flow Stress ◽  
Plastic Strain ◽  
Strain Rate ◽  
Yield Stress ◽  
Constitutive Models ◽  
Mg Alloy ◽  
Initial Yield Stress ◽  
Initial Yield ◽  
Rate Dependent ◽  
Dependent Flow

The constitutive modeling of aluminum alloy under warm forming conditions generally considers the influence of temperature and strain rate. It has been shown by published flow stress curves of Al-Mg alloy that there is nearly no effect of strain rate on initial yield stress at various temperatures. However, most constitutive models ignored this phenomenon and may lead to inaccurate description. In order to capture the rate-independent initial yield stress, Peric model is modified via introducing plastic strain to multiply the strain rate, for eliminating the effect of strain rate when the plastic strain is zero. Other constitutive models including the Wagoner, modified Hockett–Sherby and Peric are also considered and compared. The results show that the modified Peric model could not only describe the temperature-and rate-dependent flow stress, but also capture the rate-independent initial yield stress, while the Wagoner, modified Hockett–Sherby and Peric model can only describe the temperature-and rate-dependent flow stress. Moreover, the modified Peric model could obtain proper static yield stress more naturally, and this property may have potential applications in rate-dependent simulations.

A Study of Strain and Strain-Rate Dependent Properties of a Superplastic Zn-Al Alloy Under Biaxial Stresses

1982 ◽  
Vol 104 (1) ◽  
pp. 41-46
Author(s):  
T. C. Hsu ◽  
I. M. Bidhendi
Keyword(s):  
Strain Rate ◽  
Stress Ratio ◽  
Local Stress ◽  
Biaxial Stress ◽  
Al Alloy ◽  
Local Geometry ◽  
Forming Process ◽  
Rate Dependent ◽  
Strain And Strain Rate ◽  
Liquid Behavior

A superplastic Zn-Al alloy in sheet form is formed into a bulge over a circular hole by pneumatic pressure. The geometry, the stress, the strain, and the strain-rate are determined at various points covering the whole specimen and at various stages of the forming process. The complicated shape, and its complicated changes, are represented by introducing an index for the local geometry, called “prolateness,” which is also related to the local stress ratio in a simple way. The biaxial stress is analyzed into a strain-proportional and a strain-rate-proportional component, which represent, respectively, the quasi-solid and the quasi-liquid behavior of the superplastic material.

Sign in / Sign up

Export Citation Format

Share Document