The effect of retained austenite on the fracture toughness of high-speed steels

1987 ◽  
Vol 58 (2) ◽  
pp. 87-92 ◽  
Author(s):  
Jerzy Pacyna
Keyword(s):  
Fracture Toughness ◽  
Retained Austenite ◽  
High Speed

COPPER ALLOY No. C94300

Alloy Digest ◽  
1984 ◽  
Vol 33 (1) ◽  
Keyword(s):  
Fracture Toughness ◽  
Compressive Strength ◽  
Corrosion Resistance ◽  
Copper Alloy ◽  
High Speed ◽  
Heat Treating ◽  
Lead Alloy ◽  
Good Resistance ◽  
Tin Bronze ◽  
Strength Medium

Abstract Copper Alloy No. C94300 is a cast copper-tin-lead alloy (bronze). It is characterized by low hardness and strength, medium ductility, excellent machinability and good resistance to corrosion. Commercial names formerly used (but not recommended) are (1) Ingot No. 322, (2) Soft Bronze, (3) High-Leaded Tin Bronze and (4) 70-5-25. This alloy is recommended highly for high-speed bearings at light loads. This datasheet provides information on composition, physical properties, hardness, elasticity, tensile properties, and compressive strength as well as fracture toughness. It also includes information on corrosion resistance as well as casting, heat treating, machining, and joining. Filing Code: Cu-470. Producer or source: Copper alloy foundries.

CYCLOPS BHT

Alloy Digest ◽  
1965 ◽  
Vol 14 (2) ◽  
Keyword(s):  
Fracture Toughness ◽  
Corrosion Resistance ◽  
Elevated Temperature ◽  
High Speed ◽  
High Speed Steel ◽  
High Strength ◽  
Heat Treating ◽  
High Load ◽  
Structural Components ◽  
Temperature Performance

Abstract Cyclops BHT is a low-alloy martensitic high-speed steel of the molybdenum type recommended for high strength, high load structural components designed for elevated temperature service. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fracture toughness. It also includes information on high temperature performance and corrosion resistance as well as forming, heat treating, machining, and joining. Filing Code: SA-173. Producer or source: Cyclops Corporation.

ELECTRITE COBALT

Alloy Digest ◽  
1960 ◽  
Vol 9 (2) ◽  
Keyword(s):  
Fracture Toughness ◽  
Physical Properties ◽  
High Speed ◽  
Cutting Tools ◽  
High Speed Steel ◽  
Heat Treating ◽  
Heavy Duty ◽  
Steel Company

Abstract ELECTRITE COBALT is a 5% cobalt type high-speed steel recommended for heavy duty cutting tools. This datasheet provides information on composition, physical properties, hardness, and elasticity as well as fracture toughness. It also includes information on forming, heat treating, and machining. Filing Code: TS-89. Producer or source: Latrobe Steel Company.

MOTUNG 652

Alloy Digest ◽  
1957 ◽  
Vol 6 (8) ◽  
Keyword(s):  
Fracture Toughness ◽  
Physical Properties ◽  
Tensile Properties ◽  
Sulfur Content ◽  
High Speed ◽  
High Speed Steel ◽  
Heat Treating ◽  
Bend Strength ◽  
Machining Properties

Abstract MOTUNG 652 is an intermediate molybdenum-tungsten type of high-speed steel conforming to the M-2 analysis. It is available with normal sulfur content or with high sulfur for free machining properties. This datasheet provides information on composition, physical properties, hardness, tensile properties, and compressive and bend strength as well as fracture toughness. It also includes information on forming, heat treating, and machining. Filing Code: TS-61. Producer or source: Cyclops Corporation.

EXOCUT

Alloy Digest ◽  
1973 ◽  
Vol 22 (11) ◽  
Keyword(s):  
Fracture Toughness ◽  
Surface Treatment ◽  
Tool Steel ◽  
High Speed ◽  
Heat Treating ◽  
Heat Treated

Abstract EXOCUT is a super high-speed tool steel capable of being heat treated to Rockwell C 70. It is well suited for machining hard and difficult-to-machine materials. This datasheet provides information on composition, hardness, and elasticity as well as fracture toughness. It also includes information on forming, heat treating, machining, and surface treatment. Filing Code: TS-265. Producer or source: Allegheny Ludlum Corporation.

AISI TYPE M2

Alloy Digest ◽  
1972 ◽  
Vol 21 (2) ◽  
Keyword(s):  
Fracture Toughness ◽  
Wear Resistance ◽  
Compressive Strength ◽  
Physical Properties ◽  
High Speed ◽  
High Speed Steel ◽  
Heat Treating ◽  
General Purpose ◽  
Steel Mills ◽  
Aisi Type

Abstract AISI TYPE M2 is a molybdenum-tungsten high-speed steel with a balanced analysis which produces properties applicable to all general-purpose high-speed uses. It has an excellent balance between toughness and wear resistance. This datasheet provides information on composition, physical properties, hardness, and compressive strength as well as fracture toughness. It also includes information on forming, heat treating, machining, and joining. Filing Code: TS-240. Producer or source: Tool steel mills.

RED CUT COBALT

Alloy Digest ◽  
1980 ◽  
Vol 29 (8) ◽  
Keyword(s):  
Fracture Toughness ◽  
Cast Iron ◽  
High Speed ◽  
Elevated Temperatures ◽  
High Speed Steel ◽  
Heat Treating ◽  
High Speeds ◽  
Red Hardness ◽  
Nonferrous Alloys ◽  
Cutting Point

Abstract RED CUT COBALT steel is made by adding 5% cobalt to the conventional 18% tungsten -4% chromium-1% vanadium high-speed steel. Cobalt increases hot or red hardness and thus enables the tool to maintain a higher hardness at elevated temperatures. This steel is best adapted for hogging cuts or where the temperature of the cutting point of the tool in increased greatly. It is well adapted for tools to be used for reaming cast-iron engine cylinders, turning alloy steel or cast iron and cutting nonferrous alloys at high speeds. This datasheet provides information on composition, physical properties, and hardness as well as fracture toughness. It also includes information on forming, heat treating, and machining. Filing Code: TS-367. Producer or source: Teledyne Vasco.

VASCO 8-N-2

Alloy Digest ◽  
1979 ◽  
Vol 28 (7) ◽  
Keyword(s):  
Fracture Toughness ◽  
Physical Properties ◽  
High Speed ◽  
Cutting Tools ◽  
High Speed Steel ◽  
Heat Treating ◽  
General Purpose

Abstract VASCO 8-N-2 is a molybdenum high-speed steel containing a low percentage of tungsten. It can be used successfully for a variety of cutting tools; in fact, it is a general-purpose high-speed steel. Its composition represents the first molybdenum high-speed steel to be manufactured and find practical use in the field of cutting tools. Its many uses include drills, milling cutters, lathe tools, blanking dies and special shear blades. This datasheet provides information on composition, physical properties, hardness, and elasticity as well as fracture toughness. It also includes information on forming, heat treating, and machining. Filing Code: TS-351. Producer or source: Teledyne Vasco.

TATMO V

Alloy Digest ◽  
1985 ◽  
Vol 34 (1) ◽  
Keyword(s):  
Fracture Toughness ◽  
Wear Resistance ◽  
High Speed ◽  
Heat Treating ◽  
Steel Company ◽  
Treated Steel ◽  
Heat Treated ◽  
Red Hardness ◽  
Edge Toughness ◽  
Heat Treated Steel

Abstract TATMO-V is a high-speed tool steel with superior abrasion resistance because of its high contents of carbon and vanadium. It is an excellent choice for premium grade tools which require an outstanding balance of red hardness, edge toughness, and wear resistance. Increased tool life of Tatmo-V is noted in the machining of semi-hard, heat-treated steel pats (300-350 Brinell). This datasheet provides information on composition, physical properties, hardness, and elasticity as well as fracture toughness. It also includes information on forming, heat treating, and machining. Filing Code: TS-434. Producer or source: Latrobe Steel Company.

CRUCIBLE CPM REX 121

Alloy Digest ◽  
2001 ◽  
Vol 50 (10) ◽  
Keyword(s):  
Fracture Toughness ◽  
Wear Resistance ◽  
High Temperature ◽  
High Speed ◽  
High Speed Steel ◽  
Heat Treating ◽  
Maximum Hardness ◽  
Temperature Performance ◽  
Red Hardness ◽  
Cutting Speeds

Abstract CPM Rex 121 is a super high-speed steel with significantly higher wear resistance and red hardness than other high-speed steels. It is best suited for applications requiring high cutting speeds. It may provide an alternative to carbide where carbide cutting edges are too fragile. The annealed hardness is approximately 350-400 HB, and maximum hardness is approximately 72 HRC. This datasheet provides information on composition, physical properties, microstructure, hardness, and elasticity as well as fracture toughness. It also includes information on high temperature performance and wear resistance as well as heat treating and surface treatment. Filing Code: TS-591. Producer or source: Crucible.

Sign in / Sign up

Export Citation Format

Share Document