Evaluation of surface preparation methods for glass

2001 ◽  
Vol 31 (5) ◽  
pp. 362-368 ◽  
Author(s):  
N. P. Mellott ◽  
S. L. Brantley ◽  
J. P. Hamilton ◽  
C. G. Pantano
Keyword(s):  
Surface Preparation ◽  
Preparation Methods

Recommended Practices For Shop Cleaning And Priming

CORROSION ◽  
1961 ◽  
Vol 17 (8) ◽  
pp. 413t-414t
Author(s):  
◽  
Keyword(s):  
Surface Preparation ◽  
Preparation Methods ◽  
White Metal ◽  
Application Methods ◽  
Recommended Practices ◽  
Methods Of Application

Abstract Recommendations for shop cleaning and priming practices are broken down into seven categories: methods of surface preparation, methods of application, workmanship, supervision, inspection, priming, and fabrication. Surface preparation methods discussed include solvent cleaning, hand cleaning, power tool cleaning, flame cleaning, brush-off blast cleaning, commercial blast cleaning, white metal blast cleaning, and pickling. Application methods considered include brush, spray, hot spray, airless spray, roller, and dip. 5.9.1, 1.7.1, 5.4.7

Synthesis of ZrO2 Nanotubes by Anodization of Zr Foil

2015 ◽  
Vol 799-800 ◽  
pp. 125-129
Author(s):  
Mary Donnabelle L. Balela ◽  
April Alexa S. Lagarde ◽  
Stephen Jann A. Tamayo ◽  
Nikko S. Villareal ◽  
Ann Marielle Parreno
Keyword(s):  
Aqueous Solution ◽  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Surface Preparation ◽  
The Other ◽  
Preparation Methods ◽  
X Ray ◽  
Anodization Time ◽  
Other Hand ◽  
Scanning Electron

Zirconia (ZrO2) nanotubes were synthesized by anodization of zirconium (Zr) foil in NH4Fand (NH4)2SO4 aqueous solution. Different surface preparation methods (electropolishing and etching) were applied on the Zr foil prior to anodizaton. In addition, the anodization time and NH4F concentration were varied. The structure and morphologies of the nanotubes and their crystallinity were confirmed using scanning electron microscope and x-ray diffractometer, respectively. ZrO2 nanotubes with large diameters and thick walls were formed at lower NH4F concentration and longer anodization time. On the other hand, smaller nanotubes with thinner walls were produced when the NH4F concentration was increased. The synthesized nanotubes were predominantly tetragonal ZrO2 with small amounts of monoclinic ZrO2.

Dry Surface Preparation Using Supercritical Cryogenic Nitrogen Jet Improves the Adhesion Strength of Cold Gas Sprayed Coatings (SCNCS)

2018 ◽  
Vol 941 ◽  
pp. 1668-1673
Author(s):  
Abdel Tazibt ◽  
Guillaume Ezo'o ◽  
Yosri Khalsi ◽  
Mustapha Yahiaoui
Keyword(s):  
Surface Preparation ◽  
Cold Spraying ◽  
Substrate Preparation ◽  
Preparation Methods ◽  
Adhesion Performance ◽  
Pulsed Water Jet ◽  
Sprayed Coating ◽  
Sprayed Coatings ◽  
Required Quality

The adhesion performance of Cold Sprayed coatings depends on the quality of the substrate [1,2,4,8]. Before deposition, the surface of substrate must be prepared to a specific required quality, which promotes the anchoring of sprayed coating. Grit Blasting (Samson et al.) [1] is known as the conventional surface preparation before Cold Spraying. But such method causes issues: a) shallow roughness, which does not strengthen bonds between layer and substrate; b) embedment of particles in the substrate, which creates discontinuity of the material at the interface and causes cracks that degrade the layer. Recently, Laser [2] and Pulsed Water Jet (PWJ) [1] have been tested as substrate preparation methods. These methods have shown their ability to generate improved roughness without particle embedment. PWJ has particularly shown interest in Al substrate to generate crevices, which are anchors for the Cold Sprayed coatings. Nevertheless, Laser affects thermally the substrate and induces constraints that may disadvantage the coating quality. PWJ generates liquid effluents. Besides some substrates such as ferrous metals can react with oxygen of water leading to corrosion and coating adhesion weakness.

Sign in / Sign up

Export Citation Format

Share Document