Graphene oxide crosslinker for the enhancement of mechanical properties of polylactic acid

2021 ◽  
Author(s):  
Majharul Islam Sujan ◽  
Stephen Don Sarkar ◽  
Chanchal Kumar Roy ◽  
Mohammad Ferdous ◽  
Ankur Goswami ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Graphene Oxide ◽  
Polylactic Acid

Synergistic Effect between Modified Graphene Oxide and Ammonium Polyphosphate on Combustion Performance, Thermal Stability and Mechanical Properties of Polylactic Acid

2021 ◽  
Vol 36 (4) ◽  
pp. 367-378
Author(s):  
X.-Y. Pang ◽  
Y.-F. Meng ◽  
Y.-P. Xin ◽  
R. Chang ◽  
J.-Z. Xu
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Graphene Oxide ◽  
Heat Release ◽  
Polylactic Acid ◽  
Network Structure ◽  
Ammonium Polyphosphate ◽  
Limiting Oxygen Index ◽  
Combustion Performance ◽  
Modified Graphene Oxide

Abstract To improve the thermal stability, ZF-GO (graphene oxide (GO) modified by zinc ferrite (ZF)) is prepared. In view of the anti-dripping function of ZF-GO and flame retardant effect of ammonium polyphosphate (APP), the influence of ZF-GO, APP, mixture of ZF-GO and APP on combustion performance, thermal stability and mechanical properties of polylactic acid (PLA) is investigated. Results show that the modification of GO by ZF significantly improves the residue of ZFGO by 34.7%. The char-forming capability and unique network structure of ZF-GO prevent the melt dripping of PLA. Although APP can increase the limiting oxygen index of PLA, there is still melt dripping. The combination of ZF-GO and APP improves the residual yield of 94PLA/3ZF-GO/3APP by 4.3 times relative to pure PLA, and the UL-94 level reaches V-0. The two additives show synergistic char-forming effect, and there is both physical carbonization and chemical carbonization. The incorporated fillers can decrease the total heat release (THR) of PLA composites. Specifically, the THR and peak value of heat release rate of 94PLA/3ZF-GO/3APP decrease by 21.2% and 53.9%, respectively. For the PLA/ZF-GO/APP system, plenty of residues and the anti-dripping network structure are key factors to get good flame retardancy. Addition of ZFGO and APP reduces the tensile strength, but the tensile elongation of the modified PLA composites is improved. 94PLA/ 3ZF-GO/3APP shows good integrated performance.

scholarly journals Preparation of Long Sisal Fiber-Reinforced Polylactic Acid Biocomposites with Highly Improved Mechanical Performance

Polymers ◽  
2021 ◽  
Vol 13 (7) ◽  
pp. 1124
Author(s):  
Zhifang Liang ◽  
Hongwu Wu ◽  
Ruipu Liu ◽  
Caiquan Wu
Keyword(s):  
Mechanical Properties ◽  
Polylactic Acid ◽  
Mechanical Performance ◽  
Tensile Elongation ◽  
Sisal Fiber ◽  
Fiber Reinforced ◽  
Impact Performance ◽  
The Matrix ◽  
Blending Process ◽  
Extension Direction

Green biodegradable plastics have come into focus as an alternative to restricted plastic products. In this paper, continuous long sisal fiber (SF)/polylactic acid (PLA) premixes were prepared by an extrusion-rolling blending process, and then unidirectional continuous long sisal fiber-reinforced PLA composites (LSFCs) were prepared by compression molding to explore the effect of long fiber on the mechanical properties of sisal fiber-reinforced composites. As a comparison, random short sisal fiber-reinforced PLA composites (SSFCs) were prepared by open milling and molding. The experimental results show that continuous long sisal fiber/PLA premixes could be successfully obtained from this pre-blending process. It was found that the presence of long sisal fibers could greatly improve the tensile strength of LSFC material along the fiber extension direction and slightly increase its tensile elongation. Continuous long fibers in LSFCs could greatly participate in supporting the load applied to the composite material. However, when comparing the mechanical properties of the two composite materials, the poor compatibility between the fiber and the matrix made fiber’s reinforcement effect not well reflected in SSFCs. Similarly, the flexural performance and impact performance of LSFCs had been improved considerably versus SSFCs.

scholarly journals Water lubrication of graphene oxide-based materials

Friction ◽  
2021 ◽  
Author(s):  
Shaoqing Xue ◽  
Hanglin Li ◽  
Yumei Guo ◽  
Baohua Zhang ◽  
Jiusheng Li ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Graphene Oxide ◽  
Lubrication Theory ◽  
Lubricant Additives ◽  
Water Lubrication ◽  
Broad Application ◽  
Water Dispersibility ◽  
Metal Processing ◽  
The Relationship ◽  
Ph Concentration

AbstractWater is as an economic, eco-friendly, and efficient lubricant that has gained widespread attention for manufacturing. Using graphene oxide (GO)-based materials can improve the lubricant efficacy of water lubrication due to their outstanding mechanical properties, water dispersibility, and broad application scenarios. In this review, we offer a brief introduction about the background of water lubrication and GO. Subsequently, the synthesis, structure, and lubrication theory of GO are analyzed. Particular attention is focused on the relationship between pH, concentration, and lubrication efficacy when discussing the tribology behaviors of pristine GO. By compounding or reacting GO with various modifiers, amounts of GO-composites are synthesized and applied as lubricant additives or into frictional pairs for different usage scenarios. These various strategies of GO-composite generate interesting effects on the tribology behaviors. Several application cases of GO-based materials are described in water lubrication, including metal processing and bio-lubrication. The advantages and drawbacks of GO-composites are then discussed. The development of GO-based materials for water lubrication is described including some challenges.

Sign in / Sign up

Export Citation Format

Share Document