Mechanical properties of esterified tapioca starch-LDPE blends using LDPE-co-glycidyl methacrylate as compatibilizer

2004 ◽  
Vol 54 (2) ◽  
pp. 286-296 ◽  
Author(s):  
RRN Sailaja
Keyword(s):  
Mechanical Properties ◽  
Glycidyl Methacrylate ◽  
Tapioca Starch

Mechanical properties of tapioca-starch edible films containing sorbates

LWT ◽  
2005 ◽  
Vol 38 (6) ◽  
pp. 631-639 ◽  
Author(s):  
Lucía Famá ◽  
Ana M. Rojas ◽  
Silvia Goyanes ◽  
Lía Gerschenson
Keyword(s):  
Mechanical Properties ◽  
Edible Films ◽  
Tapioca Starch

The effect of simultaneous fiber surface treatment and matrix modification on mechanical properties of unidirectional ultra-high molecular weight polyethylene fiber/epoxy/nanoclay nanocomposites

2018 ◽  
Vol 52 (21) ◽  
pp. 2961-2972 ◽  
Author(s):  
Mohammad Mohammadalipour ◽  
Mahmood Masoomi ◽  
Mojtaba Ahmadi ◽  
Zahra Kazemi
Keyword(s):  
Mechanical Properties ◽  
Molecular Weight ◽  
Tensile Strength ◽  
High Molecular Weight ◽  
Glycidyl Methacrylate ◽  
Interfacial Adhesion ◽  
Fiber Surface ◽  
Cohesive Failure ◽  
Polyethylene Fiber ◽  
Ultra High Molecular Weight

Nonpolar structure of ultra-high molecular weight polyethylene fiber leads to a weak interfacial adhesion in ultra-high molecular weight polyethylene fiber reinforced epoxy composite. Herein, synchronized fiber and matrix modifications were utilized so as to improve the interfacial adhesion, resulting in promoting mechanical properties of these composites. For this purpose, the surface of ultra-high molecular weight polyethylene fiber was chemically treated with glycidyl methacrylate and the epoxy resin was modified through incorporation of different contents of nanoclay. The mechanical properties results showed that individual modification, either fiber or matrix, can just lead to improvements around 36.74% and 10.54% in tensile strength as well as 14.28% and 4.27% in tensile modulus, respectively. However, the ultimate outcome of the study revealed that much higher improvement can be achieved in synergistic attitude. The highest enhancement around 48.31% and 26.76% in tensile strength and modulus were seen for the sample containing glycidyl methacrylate-treated ultra-high molecular weight polyethylene fibers as reinforcement and nano epoxy modified with 1 wt.% of nanoclay. Such observation could be attributed to the mechanical interlocking and chemical reaction which were arising from incorporation of nanoclay in matrix and chemical treatment of fiber surface, correspondingly. In this regard, fiber roughness and chemical bonds formed between treated fiber and modified matrix play a key role in improving interfacial adhesion. Moreover, the fractured surface of such composites studied by scanning electron microscope confirmed the mechanical results and showed that much more matrix was adhered to the fiber surface after treatment, indicating cohesive failure.

PENGARUH LAMA WAKTU PENGGETARAN ULTRASONIC BATH TERHADAP SIFAT MEKANIK DAN MORFOLOGI PATAHAN BIOKOMPOSIT PATI TAPIOKA/SERAT RAMI (BOEHMERIA NIVEA)

ROTOR ◽  
2017 ◽  
Vol 10 (2) ◽  
pp. 23
Author(s):  
Mochamad Asrofi ◽  
Hairul Abral ◽  
Anwar Kasim ◽  
Adjar Pratoto ◽  
Herwin Gevin ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Fracture Surface ◽  
Tensile Test ◽  
Dry Weight ◽  
Ramie Fiber ◽  
Compact Structure ◽  
Tapioca Starch ◽  
Ultrasonic Bath ◽  
Vibration Time

This study reported about mechanical properties and fracture surface of ramie fiber reinforced tapioca starch based biocomposites. The amount of fibers in matrix was kept constant at 10% from dry weight starch basis. Fabrication of biocomposites was solution casting. The effect of vibration duration from ultrasonic bath was 0, 15, 30, and 45 min. This treatment was applied to biocomposites while gelatinized. Tensile test was carried out to determine the mechanical properties of biocomposites. Fracture surface of biocomposites after tensile test was observed by using scanning electron microscopy (SEM). The result shows that, tensile strength increased when vibration time was added. The maximum tensile strength was obtained at 45 min vibration time with 2,84 MPa. This phenomenon was supported by SEM observation which indicate compact structure. Keywords: Tapioca starch, ramie fiber, biocomposites, mechanical properties, SEM

Mechanical Properties of Poly(Butylene Succinate) Reinforced with Alpha Cellulose

2015 ◽  
Vol 1119 ◽  
pp. 283-287
Author(s):  
Sarit Liprapan ◽  
Thumnoon Nhujak ◽  
Pranut Potiyaraj
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Flexural Strength ◽  
Young’S Modulus ◽  
Glycidyl Methacrylate ◽  
Interfacial Interaction ◽  
Twin Screw Extruder ◽  
Screw Extruder ◽  
Butylene Succinate ◽  
Twin Screw

The objective of this study is to prepare α-cellulose reinforced poly (butylene succinate) composites (PBS/α-cellulose). The effect of amount α-cellulose on the mechanical properties of the composites was investigated. To improve interfacial interaction between PBS and α-cellulose, glycidyl methacrylate grafted poly (butylene succinate) (PBS-g-GMA) was used as a compatibilizer. Mechanical properties of PBS composites prepared by using a twin-screw extruder were investigated. The mechanical properties of PBS/α-cellulose decreased due to the agglomeration of α-cellulose. Nevertheless, tensile strength, Young’s modulus and flexural strength of PBS composites were improved after the incorporation of PBS-g-GMA. The optimum loading of PBS-g-GMA and α-cellulose in the PBS was found to be 5 and 6 phr.

Sign in / Sign up

Export Citation Format

Share Document