Effect of non‐woven flax mat manufacturing parameters and consolidation pressure on properties of composites manufactured using vacuum‐assisted resin transfer molding

2021 ◽  
Author(s):  
Md Shadhin ◽  
Raghavan Jayaraman ◽  
Mashiur Rahman
Keyword(s):  
Resin Transfer Molding ◽  
Transfer Molding ◽  
Consolidation Pressure ◽  
Manufacturing Parameters ◽  
Properties Of Composites

Applying Magnetic Consolidation Pressure During Cure to Improve Laminate Quality: A Comparative Analysis of Wet Lay-Up and Vacuum Assisted Resin Transfer Molding Processes

2017 ◽  
Author(s):  
Maya Pishvar ◽  
Mehrad Amirkhosravi ◽  
M. Cengiz Altan
Keyword(s):  
Composite Laminates ◽  
Permanent Magnets ◽  
Volume Fraction ◽  
Resin Transfer Molding ◽  
Void Content ◽  
Fiber Volume ◽  
Transfer Molding ◽  
Consolidation Pressure ◽  
A New Technique

This paper presents the application of a new technique, Magnet Assisted Composite Manufacturing (MACM), to enhance the quality of composite laminates fabricated by wet lay-up/vacuum bag (WLVB) and vacuum assisted resin transfer molding (VARTM). Towards this goal, a set of high-power, Neodymium permanent magnets, which are placed on a magnetic tool plate, is applied on the vacuum bag/lay-up. To further demonstrate the effectiveness of MACM, six-ply random mat, E-glass/epoxy composite laminates are produced under four processing scenarios: (i) Conventional WLVB; (ii) WLVB with magnetic consolidation; (iii) Conventional VARTM; and (iv) VARTM with magnetic consolidation. Applying magnetic consolidation pressure is found to be a convenient and efficient method for enhancing the overall quality of the laminates fabricated by WLVB and VARTM. For instance, in WLVB-MACM process, fiber volume fraction improves by 98% to 49% and void content reduces from 5% to less than 1.5% compared to conventional WLVB. These two factors lead to substantially increased mechanical properties of the WLVB-MACM laminates to a level comparable to those achieved by the higher-cost VARTM-MACM process.

Graphene nanocomposites: A review on processes, properties, and applications

2021 ◽  
pp. 152808372110242
Author(s):  
Kadir Bilisik ◽  
Mahmuda Akter
Keyword(s):  
Textile Industry ◽  
In Situ Polymerization ◽  
Resin Transfer Molding ◽  
Single Layer ◽  
Chemical Vapor ◽  
Synthesis Process ◽  
Graphene Nanocomposites ◽  
Transfer Molding ◽  
Potential Applications ◽  
Nano Graphene

In this paper, graphene, graphene/matrix, and graphene/fiber nanocomposites, including their synthesis process, fabrication, properties, and potential applications, were reviewed. It was found that several synthesis techniques for nanographene were developed, such as liquid-phase exfoliation and chemical vapor deposition. In addition, some fabrication processes of graphene/matrix and graphene/fiber-based nanocomposites were made, including in-situ polymerization, nanostitching in that single layer nano graphene plate could be interconnected by means of carbon nanotube stitching, resin transfer molding, and vacuum-assisted resin transfer molding. Several properties, including mechanical, thermal, and electrical, on the graphene nanoplatelets materials were summarized in this review paper. It was realized that graphene, graphene/matrix, and graphene/fiber nanocomposites have extraordinary mechanical, thermal, and electrical properties used in advanced engineering applications, including soft robotics, microelectronics, energy storage, biomedical and biosensors as well as textile industry.

scholarly journals A Conceptional Approach of Resin-Transfer-Molding to Rosin-Sourced Epoxy Matrix Green Composites

Aerospace ◽  
2020 ◽  
Vol 8 (1) ◽  
pp. 5
Author(s):  
Sicong Yu ◽  
Xufeng Zhang ◽  
Xiaoling Liu ◽  
Chris Rudd ◽  
Xiaosu Yi
Keyword(s):  
Composite Laminates ◽  
Resin Transfer Molding ◽  
High Viscosity ◽  
Ramie Fiber ◽  
Liquid Composite Molding ◽  
Curing Agent ◽  
Molding Process ◽  
Transfer Molding ◽  
Low Viscosity ◽  
Composite Molding

In this concept-proof study, a preform-based RTM (Resin Transfer Molding) process is presented that is characterized by first pre-loading the solid curing agent onto the preform, and then injecting the liquid nonreactive resin with an intrinsically low viscosity into the mold to infiltrate and wet the pre-loaded preform. The separation of resin and hardener helped to process inherently high viscosity resins in a convenient way. Rosin-sourced, anhydrite-cured epoxies that would normally be regarded as unsuited to liquid composite molding, were thus processed. Rheological tests revealed that by separating the anhydrite curing agent from a formulated RTM resin system, the remaining epoxy liquid had its flowtime extended. C-scan and glass transition temperature tests showed that the preform pre-loaded with anhydrite was fully infiltrated and wetted by the liquid epoxy, and the two components were diffused and dissolved with each other, and finally, well reacted and cured. Composite laminates made via this approach exhibited roughly comparable quality and mechanical properties with prepreg controls via autoclave or compression molding, respectively. These findings were verified for both carbon and ramie fiber composites.

Optimization of Resin Infusion Processing for Composite Pipe Key-Part and K/T Type Joints Using Vacuum-Assisted Resin Transfer Molding

2016 ◽  
Vol 23 (5) ◽  
pp. 1065-1078 ◽  
Author(s):  
Changchun Wang ◽  
Guanghui Bai ◽  
Guangquan Yue ◽  
Zhuxi Wang ◽  
Jin Li ◽  
...  
Keyword(s):  
Resin Transfer Molding ◽  
Resin Infusion ◽  
Transfer Molding ◽  
Composite Pipe
Sign in / Sign up

Export Citation Format

Share Document