scholarly journals The dependence of stress and strain rate on the deformation behavior of a Ni‐based single crystal superalloy at 1050°C

2021 ◽  
Author(s):  
Qingqing Ding ◽  
Hongbin Bei ◽  
Lulu Li ◽  
Jie Ouyang ◽  
Xinbao Zhao ◽  
...  
Keyword(s):  
Strain Rate ◽  
Single Crystal ◽  
Deformation Behavior ◽  
Single Crystal Superalloy ◽  
Stress And Strain ◽  
Stress And Strain Rate

Influence of the Crystallographic Orientation of CuZn30 Single Crystal on the Portevin-Le Chatelier Effect

2013 ◽  
Vol 203-204 ◽  
pp. 406-410 ◽  
Author(s):  
Barbara Grzegorczyk ◽  
Wojciech Ozgowicz ◽  
Elżbieta Kalinowska-Ozgowicz
Keyword(s):  
Plastic Deformation ◽  
Strain Rate ◽  
Single Crystal ◽  
Single Crystals ◽  
Crystallographic Orientation ◽  
Stress And Strain ◽  
Complex Process ◽  
Orientation Axis ◽  
Chatelier Effect ◽  
Stress And Strain Rate

Plastic deformation of solid crystals is a complex process, mostly heterogeneous, due to the simultaneous effect of several deformation mechanisms. A dominating deformation mechanism depends on the properties of the material and external coefficients, viz. temperature, stress and strain rate. The applied Bridgman method permitted to obtain single crystal of the CuZn30 alloy adequate for plastic deformation investigations. Single crystal are characterized by selected crystallographic orientations from various areas of the basic triangle. In order to determine the influence of the crystallographic orientation on the Portevin-Le Chatelier effect selected single crystals were compressed at a temperature of 300°C at a strain rate of 10-3 s-1. Experiments confirmed the effect of the crystallographic orientation axis of CuZn30 single crystals on the observed differences in the intensity of stress oscillation on stress-strain curves.

scholarly journals Measurements and Characterization of Turbulence in the Tip Region of an Axial Compressor Rotor

2017 ◽  
Vol 139 (12) ◽  
Author(s):  
Yuanchao Li ◽  
Huang Chen ◽  
Joseph Katz
Keyword(s):  
Strain Rate ◽  
Shear Layer ◽  
Turbulent Flows ◽  
Reynolds Stress ◽  
Suction Side ◽  
Stress And Strain ◽  
Spatial And Temporal Variability ◽  
Mean Flow ◽  
The Mean ◽  
Stress And Strain Rate

Modeling of turbulent flows in axial turbomachines is challenging due to the high spatial and temporal variability in the distribution of the strain rate components, especially in the tip region of rotor blades. High-resolution stereo-particle image velocimetry (SPIV) measurements performed in a refractive index-matched facility in a series of closely spaced planes provide a comprehensive database for determining all the terms in the Reynolds stress and strain rate tensors. Results are also used for calculating the turbulent kinetic energy (TKE) production rate and transport terms by mean flow and turbulence. They elucidate some but not all of the observed phenomena, such as the high anisotropy, high turbulence levels in the vicinity of the tip leakage vortex (TLV) center, and in the shear layer connecting it to the blade suction side (SS) tip corner. The applicability of popular Reynolds stress models based on eddy viscosity is also evaluated by calculating it from the ratio between stress and strain rate components. Results vary substantially, depending on which components are involved, ranging from very large positive to negative values. In some areas, e.g., in the tip gap and around the TLV, the local stresses and strain rates do not appear to be correlated at all. In terms of effect on the mean flow, for most of the tip region, the mean advection terms are much higher than the Reynolds stress spatial gradients, i.e., the flow dynamics is dominated by pressure-driven transport. However, they are of similar magnitude in the shear layer, where modeling would be particularly challenging.

Research on Numerical Algorithm of Constitutive Equation under High Speed Deformation in Hadfield Steel

2012 ◽  
Vol 562-564 ◽  
pp. 688-692 ◽  
Author(s):  
Deng Yue Sun ◽  
Jing Li ◽  
Fu Cheng Zhang ◽  
Feng Chao Liu ◽  
Ming Zhang
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
Deformation Behavior ◽  
High Speed ◽  
High Strain ◽  
Equivalent Stress ◽  
Hadfield Steel ◽  
Stress And Strain ◽  
Strain Rates ◽  
The Finite Element Method

The influence of the strain rate on the plastic deformation of the metals was significant during the high strain rate of loading. However, it was very difficult to obtain high strain rate data (≥ 104 s-1) by experimental techniques. Therefore, the finite element method and iterative method were employed in this study. Numerical simulation was used to characterise the deformation behavior of Hadfield steel during explosion treatment. Base on experimental data, a modified Johnson-Cook equation for Hadfield steel under various strain rate was fitted. The development of two field variables was quantified during explosion hardening: equivalent stress and strain rates.

Sign in / Sign up

Export Citation Format

Share Document