Sodium silicate treatment for the attenuation of U(VI) by iron-bearing sediments in acidic groundwater plumes

2017 ◽  
Vol 92 (8) ◽  
pp. 1919-1927 ◽  
Author(s):  
Vasileios A Anagnostopoulos ◽  
Yelena Katsenovich ◽  
Miles Denham
Keyword(s):  
Sodium Silicate ◽  
Acidic Groundwater ◽  
Iron Bearing

scholarly journals The Effect of Fe3+ Ions on the Anionic Structure of Iron-bearing Sodium Silicate Melts.

2000 ◽  
Vol 40 (12) ◽  
pp. 1181-1187 ◽  
Author(s):  
Yasushi Sasaki ◽  
Michiya Mohri ◽  
Kentaro Suyama ◽  
Kuniyoshi Ishii
Keyword(s):  
Sodium Silicate ◽  
Silicate Melts ◽  
Iron Bearing

Study on the Chemical Modification Process of Jute Fiber

TAPPI Journal ◽  
2010 ◽  
Vol 9 (2) ◽  
pp. 23-29 ◽  
Author(s):  
Wei-ming Wang ◽  
Zai-sheng Cai ◽  
Jian-yong Yu
Keyword(s):  
Sodium Hydroxide ◽  
Sodium Silicate ◽  
Treatment Time ◽  
Jute Fiber ◽  
Process Conditions ◽  
Silicate Concentration ◽  
Sodium Hydroxide Concentration ◽  
Liquor Ratio ◽  
Degumming Process ◽  
Selection Of

Degumming of pre-chlorite treated jute fiber was studied in this paper. The effects of sodium hydroxide concentration, treatment time, temperature, sodium silicate concentration, fiber-to-liquor ratio, penetrating agent TF-107B concentration, and degumming agent TF-125A concentration were the process conditions examined. With respect to gum decomposition, fineness and mechanical properties, sodium hydroxide concentration, sodium silicate concentration, and treatment time were found to be the most important parameters. An orthogonal L9(34) experiment designed to optimize the conditions for degumming resulted in the selection of the following procedure: sodium hydroxide of 12g/L, sodium silicate of 3g/L, TF-107B of 2g/L, TF-125A of 2g/L, treatment time of 105 min, temperature of 100°C and fiber to liquor ratio of 1:20. The effect of the above degumming process on the removal of impurities was also examined and the results showed that degumming was an effective method for removing impurities, especially hemicellulose.

Sodium silicate-based composition used for water control in producing wells

2020 ◽  
pp. 82-84
Author(s):  
I.G. Fattakhov ◽  
◽  
A.S. Zhirkeev ◽  
A.K. Sakhapova ◽  
R.R. Stepanova ◽  
...  
Keyword(s):  
Sodium Silicate ◽  
Water Control

Synthesis and phase morphology investigation of simultaneous organic-inorganic IPNs based on diisocyanate, dimethacrylate, and water solution of sodium silicate

2015 ◽  
Vol 37 (2) ◽  
pp. 179-185 ◽  
Author(s):  
О.O. Brovko ◽  
◽  
L.A. Gorbach ◽  
О.D. Lutsyk ◽  
L.M. Sergeeva ◽  
...  
Keyword(s):  
Sodium Silicate ◽  
Water Solution ◽  
Phase Morphology

Leaching Studies of Cement-Glass Package Containing Sodium Borate

1986 ◽  
Vol 84 ◽  
Author(s):  
Masahiro Okamoto ◽  
Koichi Chino ◽  
Tsutomu Baba ◽  
Tatsuo Izumida ◽  
Fumio Kawamura ◽  
...  
Keyword(s):  
Sodium Silicate ◽  
Liquid Waste ◽  
Sodium Borate ◽  
Pressurized Water Reactor ◽  
X Ray Diffraction ◽  
Adsorption Ability ◽  
Pressurized Water ◽  
X Ray ◽  
Solidification Reaction ◽  
Main Components

AbstractA new solidification technique using cement-glass, which is a mixture of sodium silicate, cement, additives, and initiator of the solidification reaction, was developed for sodium borate liquid waste generated from pressurized water reactor (PWR) plants. The cement-glass could solidify eight times as much sodium borate as cement could, because the solidifying reaction of the cement-glass is not hindered by borate ions.The reaction mechanism of sodium silicate and phosphoric silicate (initiator), the main components of cement-glass, was studied through X-ray diffraction and compressive strength measurements. It was found that three- dimensionally bonded silicon dioxide was produced by polymerization of the two silicates. The leaching ratio of cesium from the cement-glass package was one-tenth that of the cement one. This low value was attributed to a high cesium adsorption ability of the cement-glass and it could be theoretically predicted accordingly.

The Effect of Dry Mix Sodium Hydroxide onto Workability and Compressive Strength of Geopolymer Paste

2020 ◽  
Vol 12 (9) ◽  
Author(s):  
A. Z. Mohd Ali ◽  
◽  
N. A. Jalaluddin ◽  
N. Zulkiflee ◽  
◽  
...  
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Sodium Hydroxide ◽  
Sodium Silicate ◽  
Alkaline Solution ◽  
High Emission ◽  
New Material ◽  
Curing Regime ◽  
Solid Form ◽  
Geopolymer Paste

The production of ordinary Portland cement (OPC) consumes considerable amount of natural resources, energy and at the same time contribute in high emission of CO2 to the atmosphere. A new material replacing cement as binder called geopolymer is alkali-activated concrete which are made from fly ash, sodium silicate and sodium hydroxide (NaOH). The alkaline solution mixed with fly ash producing alternative binder to OPC binder in concrete named geopolymer paste. In the process, NaOH was fully dissolved in water and cooled to room temperature. This study aims to eliminate this process by using NaOH in solid form together with fly ash before sodium silicate liquid and water poured into the mixture. The amount of NaOH solids were based on 10M concentration. The workability test is in accordance to ASTM C230. Fifty cubic mm of the geopolymer paste were prepared which consists of fly ash to alkaline solution ratio of 1: 0.5 and the curing regime of 80℃ for 24 hours with 100% humidity were implemented. From laboratory test, the workability of dry method geopolymer paste were decreased. The compressive strength of the dry mix of NaOH showed 55% and the workability has dropped to 58.4%, it showed strength reduction compared to the wet mix method.

Sign in / Sign up

Export Citation Format

Share Document