scholarly journals Drug release from calcium sulfate-based composites

2014 ◽  
Vol 103 (1) ◽  
pp. 135-142 ◽  
Author(s):  
Bryan R. Orellana ◽  
J. Zach Hilt ◽  
David A. Puleo
Keyword(s):  
Drug Release ◽  
Calcium Sulfate

STUDY OF THE DIFFERENT RELEASE CHARACTERISTICS OF ANTIBIOTICS FROM PATIENTS: A DYNAMIC ELUTING SYSTEM TO INVESTIGATE DRUG RELEASE FROM ANTIBIOTIC-IMPREGNATED CALCIUM SULFATE DELIVERY

2015 ◽  
Vol 15 (01) ◽  
pp. 1550012
Author(s):  
YANG ZHANG ◽  
RENJIE WU ◽  
YING HU ◽  
YU DONG ◽  
LIFENG SHEN ◽  
...  
Keyword(s):  
Drug Release ◽  
Delivery System ◽  
Release Rate ◽  
Calcium Sulfate ◽  
Fickian Diffusion ◽  
Release Behavior ◽  
Cumulative Release ◽  
In Vivo Release

Background: Antibiotic-impregnated calcium sulfate delivery systems (ACDS) are commonly used to treat chronic osteomyelitis. Our research is to investigate drug release in vitro over a longer period, as a cautious predictor of in vivo release. Methods: The local release behavior of antibiotic in vitro was simulated. The consecutive dynamic eluting experiment was performed based on the pro-operative characteristic of osteomyelitis patients and the determined results of drug concentration in the human drainage tissue fluid (DTF). The concentration of each drug in the receiving solution was detected by ultra-performance liquid chromatography-tandem quadrupole detector mass spectrometry. The ACDS was reviewed by scanning electronic microscopy (SEM) after 48 h, and prepared to be eluted for another examination after 33 days. The mechanism of antibiotic release was analyzed by using the Ritger–Peppas and Weibull equations. Results: The cumulative release rate of vancomycin in a vancomycin-calcium sulfate delivery system (VCDS) was 77.50 % (3.0 mm diameter) and 72.43 % (4.8 mm diameter), while that of the tobramycin in a tobramycin-calcium sulfate delivery system (TCDS) was 88.0 % (3.0 mm diameter) and 84.55 % (4.8 mm diameter). At the 15th day, approximately 27.92% of vancomycin was and 29.35% of tobramycin was released from the local implant in vivo. Using SEM, numerous vancomycin and tobramycin particles were found to be attached to the columnar calcium sulfate crystals at the start of the experiment. The release behavior of the two antibiotics followed a combination of Fickian diffusion and Case II transport mechanisms within the first 48 h, and a Fickian diffusion mechanism during the subsequent time period. The correlation coefficient of tobramycin and vancomycin in vivo and in vitro was 0.9704–0.9949 and 0.9549–0.9782, respectively. Conclusion: A good correlation of the in vivo and in vitro cumulative release rates was observed by comparing the cumulative release rate of drugs in vitro by means of the dynamic eluting model, and in the DTF. Therefore, our study has proved that it is possible to use the dynamic eluting model as a cautious predictor of in vivo release.

scholarly journals Assessment of the Release of Vascular Endothelial Growth Factor from 3D-Printed Poly-ε-Caprolactone/Hydroxyapatite/Calcium Sulfate Scaffold with Enhanced Osteogenic Capacity

Polymers ◽  
2020 ◽  
Vol 12 (7) ◽  
pp. 1455 ◽  
Author(s):  
Cheng-Yu Chen ◽  
Chien-Chang Chen ◽  
Chen-Ying Wang ◽  
Alvin Kai-Xing Lee ◽  
Chun-Liang Yeh ◽  
...  
Keyword(s):  
Vascular Endothelial Growth Factor ◽  
Growth Factor ◽  
Drug Release ◽  
Bone Regeneration ◽  
Bone Tissue ◽  
Calcium Sulfate ◽  
Potential Candidate ◽  
Vascular Endothelial ◽  
Fused Deposition ◽  
Endothelial Growth Factor

Vascular endothelial growth factor (VEGF) is one of the most crucial growth factors and an assistant for the adjustment of bone regeneration. In this study, a 3D scaffold is fabricated using the method of fused deposition modeling. Such a fabricated method allows us to fabricate scaffolds with consistent pore sizes, which could promote cellular ingrowth into scaffolds. Therefore, we drafted a plan to accelerate bone regeneration via VEGF released from the hydroxyapatite/calcium sulfate (HACS) scaffold. Herein, HACS will gradually degrade and provide a suitable environment for cell growth and differentiation. In addition, HACS scaffolds have higher mechanical properties and drug release compared with HA scaffolds. The drug release profile of the VEGF-loaded scaffolds showed that VEGF could be loaded and released in a stable manner. Furthermore, initial results showed that VEGF-loaded scaffolds could significantly enhance the proliferation of human mesenchymal stem cells (hMSCs) and human umbilical vein endothelial cells (HUVEC). In addition, angiogenic- and osteogenic-related proteins were substantially increased in the HACS/VEGF group. Moreover, in vivo results revealed that HACS/VEGF improved the regeneration of the rabbit’s femur bone defect, and VEGF loading improved bone tissue regeneration and remineralization after implantation for 8 weeks. All these results strongly imply that the strategy of VEGF loading onto scaffolds could be a potential candidate for future bone tissue engineering.

scholarly journals Controlled and sustained drug release performance of calcium sulfate cement porous TiO2 microsphere composites

2018 ◽  
Vol Volume 13 ◽  
pp. 7491-7501 ◽  
Author(s):  
Wei Luo ◽  
Zhen Geng ◽  
Zhaoyang Li ◽  
Shuilin Wu ◽  
Zhenduo Cui ◽  
...  
Keyword(s):  
Drug Release ◽  
Calcium Sulfate ◽  
Sustained Drug Release

Effects of sterilization modes on the mechanical strengths of plaster of paris implants

1989 ◽  
Vol 47 ◽  
pp. 890-891
Author(s):  
K. Cowden ◽  
B. Giammara ◽  
T. Devine ◽  
J. Hanker
Keyword(s):  
Gamma Radiation ◽  
Calcium Sulfate ◽  
Significant Loss ◽  
Potassium Sulfate ◽  
Limiting Factors ◽  
Radiation Sterilization ◽  
Plaster Of Paris ◽  
Hardness Tester ◽  
Dry Heat ◽  
Calcium Sulfate Hemihydrate

Plaster of Paris (calcium sulfate hemihydrate, CaSO4. ½ H2O) has been used as a biomedical implant material since 1892. One of the primary limiting factors of these implants is their mechanical properties. These materials have low compressive and tensile strengths when compared to normal bone. These are important limiting factors where large biomechanical forces exist. Previous work has suggested that sterilization techniques could affect the implant’s strength. A study of plaster of Paris implant mechanical and physical properties to find optimum sterilization techniques therefore, could lead to a significant increase in their application and promise for future use as hard tissue prosthetic materials.USG Medical Grade Calcium Sulfate Hemihydrate Types A, A-1 and B, were sterilized by dry heat and by gamma radiation. Types A and B were additionally sterilized with and without the setting agent potassium sulfate (K2SO4). The plaster mixtures were then moistened with a minimum amount of water and formed into disks (.339 in. diameter x .053 in. deep) in polyethylene molds with a microspatula. After drying, the disks were fractured with a Stokes Hardness Tester. The compressive strengths of the disks were obtained directly from the hardness tester. Values for the maximum tensile strengths σo were then calculated: where (P = applied compression, D = disk diameter, and t = disk thickness). Plaster disks (types A and B) that contained no setting agent showed a significant loss in strength with either dry heat or gamma radiation sterilization. Those that contained potassium sulfate (K2SO4) did not show a significant loss in strength with either sterilization technique. In all comparisons (with and without K2SO4 and with either dry heat or gamma radiation sterilization) the type B plaster had higher compressive and tensile strengths than that of the type A plaster. The type A-1 plaster however, which is specially modified for accelerated setting, was comparable to that of type B with K2SO4 in both compressive and tensile strength (Table 1).

Identification of acid-insoluble filter-plugging compounds and optimal acid-washing procedures for tubular backpulse pressure filters

TAPPI Journal ◽  
2011 ◽  
Vol 10 (1) ◽  
pp. 17-23
Author(s):  
KEVIN TAYLOR ◽  
RICH ADDERLY ◽  
GAVIN BAXTER
Keyword(s):  
Calcium Sulfate ◽  
Membrane Filter ◽  
Sulfamic Acid ◽  
Xrd Analysis ◽  
Metal Sulfides ◽  
X Ray Diffraction ◽  
X Ray ◽  
Gypsum Formation ◽  
Acid Washing ◽  
Hydrolysis Of

Over time, performance of tubular backpulse pressure filters in kraft mills deteriorates, even with regular acid washing. Unscheduled filter replacement due to filter plugging results in significant costs and may result in mill downtime. We identified acid-insoluble filter-plugging materials by scanning electron microscope/energy-dispersion X-ray spectroscopy (SEM/EDS) and X-ray diffraction (XRD) analysis in both polypropylene and Gore-Tex™ membrane filter socks. The major filter-plugging components were calcium sulfate (gypsum), calcium phosphate (hydroxylapatite), aluminosilicate clays, metal sulfides, and carbon. We carried out detailed sample analysis of both the standard acid-washing procedure and a modified procedure. Filter plugging by gypsum and metal sulfides appeared to occur because of the acid-washing procedure. Gypsum formation on the filter resulted from significant hydrolysis of sulfamic acid solution at temperatures greater than 130°F. Modification of the acid-washing procedure greatly reduced the amount of gypsum and addition of a surfactant to the acid reduced wash time and mobilized some of the carbon from the filter. With surfactant, acid washing was 95% complete after 40 min.

Sign in / Sign up

Export Citation Format

Share Document