In vitro analysis and mechanical properties of twin screw extruded single-layered and coextruded multilayered poly(caprolactone) scaffolds seeded with human fetal osteoblasts for bone tissue engineering

2011 ◽  
Vol 99A (3) ◽  
pp. 354-366 ◽  
Author(s):  
Asli Ergun ◽  
Xiaojun Yu ◽  
Antonio Valdevit ◽  
Arthur Ritter ◽  
Dilhan M. Kalyon
Keyword(s):  
Mechanical Properties ◽  
Tissue Engineering ◽  
Bone Tissue Engineering ◽  
Bone Tissue ◽  
Twin Screw ◽  
Vitro Analysis ◽  
Poly Caprolactone ◽  
In Vitro Analysis

scholarly journals Development of Biopolymeric Hybrid Scaffold-Based on AAc/GO/nHAp/TiO2 Nanocomposite for Bone Tissue Engineering: In-Vitro Analysis

Nanomaterials ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 1319
Author(s):  
Muhammad Umar Aslam Khan ◽  
Wafa Shamsan Al-Arjan ◽  
Mona Saad Binkadem ◽  
Hassan Mehboob ◽  
Adnan Haider ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tissue Engineering ◽  
Bone Tissue Engineering ◽  
Bone Tissue ◽  
Guar Gum ◽  
Porous Scaffolds ◽  
Vitro Assay ◽  
Vitro Analysis ◽  
Nanocomposite Scaffolds

Bone tissue engineering is an advanced field for treatment of fractured bones to restore/regulate biological functions. Biopolymeric/bioceramic-based hybrid nanocomposite scaffolds are potential biomaterials for bone tissue because of biodegradable and biocompatible characteristics. We report synthesis of nanocomposite based on acrylic acid (AAc)/guar gum (GG), nano-hydroxyapatite (HAp NPs), titanium nanoparticles (TiO2 NPs), and optimum graphene oxide (GO) amount via free radical polymerization method. Porous scaffolds were fabricated through freeze-drying technique and coated with silver sulphadiazine. Different techniques were used to investigate functional group, crystal structural properties, morphology/elemental properties, porosity, and mechanical properties of fabricated scaffolds. Results show that increasing amount of TiO2 in combination with optimized GO has improved physicochemical and microstructural properties, mechanical properties (compressive strength (2.96 to 13.31 MPa) and Young’s modulus (39.56 to 300.81 MPa)), and porous properties (pore size (256.11 to 107.42 μm) and porosity (79.97 to 44.32%)). After 150 min, silver sulfadiazine release was found to be ~94.1%. In vitro assay of scaffolds also exhibited promising results against mouse pre-osteoblast (MC3T3-E1) cell lines. Hence, these fabricated scaffolds would be potential biomaterials for bone tissue engineering in biomedical engineering.

scholarly journals A Proposed Fabrication Method of Novel PCL-GEL-HAp Nanocomposite Scaffolds for Bone Tissue Engineering Applications

2010 ◽  
Vol 19 (4) ◽  
pp. 096369351001900 ◽  
Author(s):  
A. Hamlekhan ◽  
M. Mozafari ◽  
N. Nezafati ◽  
M. Azami ◽  
H. Hadipour
Keyword(s):  
Tissue Engineering ◽  
Bone Tissue Engineering ◽  
Bone Tissue ◽  
Mechanical Test ◽  
Fibroblast Cell ◽  
Mouse Fibroblast ◽  
Fabrication Method ◽  
Engineering Applications ◽  
Poly Caprolactone

In this study, poly(∊-caprolactone) (PCL), gelatin (GEL) and nanocrystalline hydroxyapatite (HAp) was applied to fabricate novel PCL-GEL-HAp nanaocomposite scaffolds through a new fabrication method. With the aim of finding the best fabrication method, after testing different methods and solvents, the best method and solvents were found, and the nanocomposites were prepared through layer solvent casting combined with freeze-drying. Acetone and distillated water were used as the PCL and GEL solvents, respectively. The mechanical test showed that the increasing of the PCL weight through the scaffolds caused the improvement of the final nanocomposite mechanical behavior due to the increasing of the ultimate stress, stiffness and elastic modulus (8 MPa for 0% wt PCL to 23.5 MPa for 50% wt PCL). The biomineralization investigation of the scaffolds revealed the formation of bone-like apatite layers after immersion in simulated body fluid (SBF). In addition, the in vitro cytotoxity of the scaffolds using L929 mouse fibroblast cell line (ATCC) indicated no sign of toxicity. These results indicated that the fabricated scaffold possesses the prerequisites for bone tissue engineering applications.

Innovative Composite HA Scaffold Rapid Prototyping for Bone Reconstruction: An In Vitro Pilot Study

2013 ◽  
Vol 583 ◽  
pp. 56-63 ◽  
Author(s):  
Isidoro Giorgio Lesci ◽  
Leonardo Ciocca ◽  
Barbara Dozza ◽  
Enrico Lucarelli ◽  
Sergio Squarzoni ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tissue Engineering ◽  
Pilot Study ◽  
Rapid Prototyping ◽  
Bone Tissue Engineering ◽  
Bone Tissue ◽  
High Surface ◽  
Surface Reactivity ◽  
Macro Scale

The ability to control the architecture and strength of a bone tissue engineering scaffold is critical to achieve a harmony between the scaffold and the host tissue. The scaffold attempts to mimic the function of the natural extracellular matrix, providing a temporary template for the growth of target tissues. The study of nanocrystalline calcium phosphate physical-chemical characteristics and, thereafter, the possibility to imitate bone mineral for the development of new advanced biomaterials is constantly growing. Scaffolds should have suitable architecture and strength to serve their intended function. Rapid prototyping (RP) technique is applied to tissue engineering to satisfy this need and to create a scaffold directly from the scanned and digitized image of the defect site. Design and construction of complex structures with different shapes and sizes, at micro and macro scale, with fully interconnected pore structure and appropriate mechanical properties are possible by using RP techniques. In this study we present a new biocompatible hybrid scaffold obtained through two different experimental methods and formed by synthetic biomimetic Hydroxyapatite (HA) nanocrystals with high surface reactivity which synergistically interacts with Poly(e-caprolactone) (PCL) and polylactic acid (PLLA). The aim of this pilot study is to test the adhesion and the proliferation of human mesenchymal stem cells (MSC) on both the scaffolds. MSC growth and distribution was evaluated 24 h and 7 days after in-vitro seeding. The results allowed the conclusion that these scaffolds are biocompatible and allow the colonization and proliferation of MSC, therefore, due to their mechanical properties, they are adequate for bone tissue engineering.

Fabrication and characterization of electrospinning/3D printing bone tissue engineering scaffold

RSC Advances ◽  
2016 ◽  
Vol 6 (112) ◽  
pp. 110557-110565 ◽  
Author(s):  
Yinxian Yu ◽  
Sha Hua ◽  
Mengkai Yang ◽  
Zeze Fu ◽  
Songsong Teng ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tissue Engineering ◽  
3D Printing ◽  
Bone Tissue Engineering ◽  
Bone Tissue ◽  
Composite Scaffold ◽  
Tissue Engineering Scaffold ◽  
Fabrication And Characterization

A composite scaffold was fabricated with a method involving both electrospinning and 3D printing to give microscale pores and good mechanical properties. Biocompatibility and cell infiltration on the scaffold was evaluated by an in vitro study.

scholarly journals Fabrication and In Vitro Evaluation of 3D Printed Porous Polyetherimide Scaffolds for Bone Tissue Engineering

2019 ◽  
Vol 2019 ◽  
pp. 1-8 ◽  
Author(s):  
Xiongfeng Tang ◽  
Yanguo Qin ◽  
Xinyu Xu ◽  
Deming Guo ◽  
Wenli Ye ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tissue Engineering ◽  
Cell Proliferation ◽  
Cell Adhesion ◽  
3D Printing ◽  
Bone Tissue Engineering ◽  
Bone Tissue ◽  
Porous Scaffold ◽  
3D Printed

For bone tissue engineering, the porous scaffold should provide a biocompatible environment for cell adhesion, proliferation, and differentiation and match the mechanical properties of native bone tissue. In this work, we fabricated porous polyetherimide (PEI) scaffolds using a three-dimensional (3D) printing system, and the pore size was set as 800 μm. The morphology of 3D PEI scaffolds was characterized by the scanning electron microscope. To investigate the mechanical properties of the 3D PEI scaffold, the compressive mechanical test was performed via an electronic universal testing system. For the in vitro cell experiment, bone marrow stromal cells (BMSCs) were cultured on the surface of the 3D PEI scaffold and PEI slice, and cytotoxicity, cell adhesion, and cell proliferation were detected to verify their biocompatibility. Besides, the alkaline phosphatase staining and Alizarin Red staining were performed on the BMSCs of different samples to evaluate the osteogenic differentiation. Through these studies, we found that the 3D PEI scaffold showed an interconnected porous structure, which was consistent with the design. The elastic modulus of the 3D PEI scaffold (941.33 ± 65.26 MPa) falls in the range of modulus for the native cancellous bone. Moreover, the cell proliferation and morphology on the 3D PEI scaffold were better than those on the PEI slice, which revealed that the porous scaffold has good biocompatibility and that no toxic substances were produced during the progress of high-temperature 3D printing. The osteogenic differentiation level of the 3D PEI scaffold and PEI slice was equal and ordinary. All of these results suggest the 3D printed PEI scaffold would be a potential strategy for bone tissue engineering.

Simvastatin-loaded graphene oxide embedded in polycaprolactone-polyurethane nanofibers for bone tissue engineering applications

2021 ◽  
Vol 41 (5) ◽  
pp. 375-386
Author(s):  
Hessam Rezaei ◽  
Mostafa Shahrezaee ◽  
Marziyeh Jalali Monfared ◽  
Sonia Fathi Karkan ◽  
Robabehbeygom Ghafelehbashi
Keyword(s):  
Mechanical Properties ◽  
Tissue Engineering ◽  
Graphene Oxide ◽  
Bone Tissue Engineering ◽  
Bone Tissue ◽  
Bone Repair ◽  
Drug Carrier ◽  
Absorption Capacity ◽  
Tissue Engineering Application

Abstract Here, the role of simvastatin-loaded graphene oxide embedded in polyurethane-polycaprolactone nanofibers for bone tissue engineering has been investigated. The scaffolds were physicochemically and mechanically characterized, and obtained polymeric composites were used as MG-63 cell culture scaffolds. The addition of graphene oxide-simvastatin to nanofibers generates a homogeneous and uniform microstructure as well as a reduction in fiber diameter. Results of water-scaffolds interaction indicated higher hydrophilicity and absorption capacity as a function of graphene oxide addition. Scaffolds’ mechanical properties and physical stability improved after the addition of graphene oxide. Inducing bioactivity after the addition of simvastatin-loaded graphene oxide terminated its capability for hard tissue engineering application, evidenced by microscopy images and phase characterization. Nanofibrous scaffolds could act as a sustained drug carrier. Using the optimal concentration of graphene oxide-simvastatin is necessary to avoid toxic effects on tissue. Results show that the scaffolds are biocompatible to the MG-63 cell and support alkaline phosphatase activity, illustrating their potential use in bone tissue engineering. Briefly, graphene-simvastatin-incorporated in polymeric nanofibers was developed to increase bioactive components’ synergistic effect to induce more bioactivity and improve physical and mechanical properties as well as in vitro interactions for better results in bone repair.

scholarly journals Graphene Oxide Encapsulated Forsterite Scaffolds: Synergistic Influences on Mechanical Properties and Antibacterial Behavior 

2021 ◽  
Author(s):  
A. Najafinezhad ◽  
H. R. Bakhsheshi-Rad ◽  
A. Saberi ◽  
A. A. Nourbakhsh ◽  
M. Daroonparvar ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tissue Engineering ◽  
Graphene Oxide ◽  
Bone Tissue Engineering ◽  
Bone Tissue ◽  
Antibacterial Properties ◽  
Immersion Test ◽  
Antibacterial Performance ◽  
The Matrix

Abstract It is very desirable to have good antibacterial properties and mechanical properties at the same time for bone scaffolds. Graphene oxide (GO) can increase the mechanical properties and antibacterial performance, while forsterite (Mg2SiO4) as the matrix can increase forsterite/GO scaffolds' biological activity for bone tissue engineering. Interconnected porous forsterite scaffolds were developed by space holder processes for bone tissue engineering in this research. The forsterite/GO scaffolds had a porosity of 77-80%. The mechanism of the mechanical strengthening, antibacterial activity, and cellular function of the forsterite/GO scaffold was evaluated. The findings show that the compressive strength of forsterite/1wt.% GO scaffold was significantly increased, in comparison to forsterite scaffolds without GO. Validation of the samples' bioactivity was attained by forming a hydroxyapatite layer (HAp) on the forsterite/GO surface within in vitro immersion test. The results of cell viability demonstrated that synthesized forsterite scaffolds with low GO did not show cytotoxicity and enhanced cell proliferation. Antibacterial tests showed that the antibacterial influence of forsterite/GO scaffold was strongly correlated with GO concentration. The scaffold encapsulated with 2wt.% GO had the highest bacterial inhibition. As results show, the produced forsterite/1wt.% GO can be an attractive option for bone tissue engineering.

Sign in / Sign up

Export Citation Format

Share Document