Flow Pattern and Pressure Drop for Small Long‐Cylinder Cyclones Operating at High Flow Rates

2019 ◽  
Vol 42 (9) ◽  
pp. 1960-1969
Author(s):  
Dongshen Wang ◽  
Bingtao Zhao ◽  
Yaxin Su
Keyword(s):  
Pressure Drop ◽  
Flow Pattern ◽  
High Flow ◽  
Flow Rates ◽  
Long Cylinder

scholarly journals Adapting the Forchheimer equation for the flow of air through wheat straw beds

2016 ◽  
Vol 20 (suppl. 2) ◽  
pp. 463-470
Author(s):  
Djordjije Doder ◽  
Biljana Miljkovic ◽  
Borivoj Stepanov ◽  
Ivan Pesenjanski
Keyword(s):  
Experimental Investigation ◽  
Pressure Drop ◽  
Wheat Straw ◽  
Measurement Methods ◽  
High Flow ◽  
Biomass Combustion ◽  
Inertial Effects ◽  
Forchheimer Equation ◽  
Flow Rates ◽  
Straw Bale

The paper presents the results of an experimental investigation of air pressure drop while flowing through wheat straw beds. According to Darcy?s law, the smaller the porosity of the bed is, the bigger the pressure drop will be. The investigation was conducted using three different porosities (or three bed densities), and for two different air flow rates. After determining porosity (which is directly measurable), the permeability of straw could be found. For high flow velocities, such as the velocity of air flowing through a straw bale, the Forchheimer equation becomes more relevant as a correction of Darcy?s law with inertial effects included. Otherwise, the permeability tensor depends only on the geometry of the porous medium. With permeability known, the Forchheimer equation coefficients can be easily estimated. These results may be important for the future development of efficient biomass combustion facilities. The measurement methods and facility characteristics are described in more detail.

Effect of expiratory flow patterns on lung emptying

1963 ◽  
Vol 18 (1) ◽  
pp. 47-50 ◽  
Author(s):  
A. C. Young ◽  
C. J. Martin ◽  
William R. Pace
Keyword(s):  
Carbon Dioxide ◽  
Flow Pattern ◽  
Body Position ◽  
Volume Ratio ◽  
Flow Patterns ◽  
High Flow ◽  
Low Flow ◽  
Flow Rates ◽  
Single Breath ◽  
Expiratory Flow

Differences in expired alveolar gas concentrations with changes in expiratory flow were studied in single-breath experiments using nitrogen and carbon dioxide meters. High flow rates preferentially emptied lung areas having low ventilation-to-volume ratios and high ventilation-to-perfusion ratios, whereas low flow rates preferentially emptied areas of high ventilation-to-volume and low ventilation-to-perfusion ratios. Selective emptying of different lung areas by varying the expiratory flow pattern was not affected by age, sex, or body position. A model of the lung is proposed to explain how ventilation-to-volume ratio differences can be seen at mouth level during constant slow, varying, and constantly increasing or decreasing expiratory flow. Submitted on May 4, 1962

scholarly journals Methods of Determining Pressure Drop in Internal Channels of a Hydraulic Motor

Energies ◽  
2021 ◽  
Vol 14 (18) ◽  
pp. 5669
Author(s):  
Pawel Sliwinski ◽  
Piotr Patrosz
Keyword(s):  
Pressure Drop ◽  
Experimental Studies ◽  
Experimental Tests ◽  
High Flow ◽  
Low Flow ◽  
Hydraulic Motor ◽  
Flow Rates ◽  
Pressure Losses ◽  
Face To Face ◽  
New Methods

In this paper, new methods for determining the pressure drop in internal channels of a hydraulic motor are proposed and described. Mathematical models of pressure losses in internal channels have also been described. Experimental tests of the satellite motor were carried out according to one of the proposed methods. The tests were carried out for two liquids, i.e., water and mineral oil. Experimental studies have shown that at a high flow rate in the motor supplied with water the pressure losses are a dozen or so percent greater than in the motor supplied with oil. However, at low flow rates is the inverse, that is, the pressure losses in the motor supplied with water are about ten percent lower than in the motor supplied with oil. The CFD calculation of the pressure drop in the internal channel of the motor was also conducted. It was assumed that holes in the commutation unit plate are placed face to face and that the liquid did not cause changes in the working chambers’ volume. In this way, it has been proven that those simplified assumptions can have up to a 50% difference in relation to the experimental tests.

Thermal Performance Comparison for Five Liquid Heat Sink Designs

2011 ◽  
Author(s):  
Christopher Greene ◽  
Randall D. Manteufel ◽  
Amir Karimi
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Thermal Resistance ◽  
Flow Rate ◽  
Heat Sink ◽  
Fluid Velocity ◽  
Water Flow Rate ◽  
High Flow ◽  
Heat Transfer Area ◽  
Flow Rates

Five high-flow liquid-cooled heat sink designs are compared for the cooling of a single chip CPU. Five distinctive design configurations are considered with regard to the introduction, passage, and extraction of cooling fluid. The typical water flow rate is about 3.8 liters per minute (lpm) with flow passages in the primary heat transfer area ranging from 2 to 0.1mm. The design configurations are summarized and compared, considering: the primary convective heat transfer area, flow passage streamlining, acceleration mechanisms, and nominal fluid velocity in the primary heat transfer area. Overall pressure drop and thermal resistance are compared for varying flow rates of water. At the nominal flow, the pressure drops ranged from 1 kPa to 20 kPa. In the restrictive designs, such as nozzles, flow acceleration accounts for the largest source of pressure drop. In some designs, a large fraction of the overall pressure drop is due to circuitous flow associated with the introduction and/or extraction of flow which contributes little to heat removal. At the nominal flow, the overall thermal resistance varied from 0.14 to 0.18 C/W. As flow rate increases the overall thermal resistance decreases. Results indicated that 80 to 85% of the total thermal resistance is due to conduction and about 15 to 20% attributed to convection at the nominal flow rate. There is minimal thermal benefit for flow rates beyond twice the nominal while this substantially increases fluid pumping requirements. This study highlights design features which yield above average heat transfer performance with minimal pressure drop for high-flow liquid-cooled heat sinks.

Monitoring Effects of Catchment Management Practices on Phosphorus Loads into the Eutrophic Peel-Harvey Estuary, Western Australia

1986 ◽  
Vol 18 (4-5) ◽  
pp. 53-61 ◽  
Author(s):  
P. B. Birch ◽  
G. G. Forbes ◽  
N. J. Schofield
Keyword(s):  
Management Practices ◽  
Major Change ◽  
High Flow ◽  
Catchment Management ◽  
Flow Rates ◽  
Early Results ◽  
Phosphorus Loads ◽  
Time Of Year ◽  
High Runoff

Early results from monitoring runoff suggest that the programme to reduce application of superphosphate to farmlands in surrounding catchments has been successful in reducing input of phosphorus to the eutrophic Peel-Harvey estuary. In the estuary this phosphorus fertilizes algae which grow in abundance and accumulate and pollute once clean beaches. The success of the programme has been judged from application of an empirical statistical model, which was derived from 6 years of data from the Harvey Estuary catchment prior to a major change in fertilizer practices in 1984. The model relates concentration of phosphorus with rate of flow and time of year. High phosphorus concentrations were associated with high flow rates and with flows early in the high runoff season (May-July). The model predicted that the distribution of flows in 1984 should have resulted in a flow-weighted concentration of phosphorus near the long-term average; the observed concentration was 25% below the long-term average. This means that the amount of phosphorus discharged into the Harvey Estuary could have been about 2 5% less than expected from the volume of runoff which occurred. However several more years of data are required to confirm this trend.

The effect of two-phase flow regime on hydrodynamics and mass transfer in a horizontal-tube gas-liquid reactor

1985 ◽  
Vol 50 (3) ◽  
pp. 745-757 ◽  
Author(s):  
Andreas Zahn ◽  
Lothar Ebner ◽  
Kurt Winkler ◽  
Jan Kratochvíl ◽  
Jindřich Zahradník
Keyword(s):  
Mass Transfer ◽  
Pressure Drop ◽  
Flow Regime ◽  
Liquid Flow ◽  
Horizontal Tube ◽  
Liquid Holdup ◽  
Two Phase ◽  
Flow Rates ◽  
Type Relation ◽  
Good Agreement

The effect of two-phase flow regime on decisive hydrodynamic and mass transfer characteristics of horizontal-tube gas-liquid reactors (pressure drop, liquid holdup, kLaL) was determined in a cocurrent-flow experimental unit of the length 4.15 m and diameter 0.05 m with air-water system. An adjustable-height weir was installed in the separation chamber at the reactor outlet to simulate the effect of internal baffles on reactor hydrodynamics. Flow regime maps were developed in the whole range of experimental gas and liquid flow rates both for the weirless arrangement and for the weir height 0.05 m, the former being in good agreement with flow-pattern boundaries presented by Mandhane. In the whole range of experi-mental conditions pressure drop data could be well correlated as a function of gas and liquid flow rates by an empirical exponential-type relation with specific sets of coefficients obtained for individual flow regimes from experimental data. Good agreement was observed between values of pressure drop obtained for weirless arrangement and data calculated from the Lockhart-Martinelli correlation while the contribution of weir to the overall pressure drop was well described by a relation proposed for the pressure loss in closed-end tubes. In the region of negligible weir influence values of liquid holdup were again succesfully correlated by the Lockhart-Martinelli relation while the dependence of liquid holdup data on gas and liquid flow rates obtained under conditions of significant weir effect (i.e. at low flow rates of both phases) could be well described by an empirical exponential-type relation. Results of preliminary kLaL measurements confirmed the decisive effect of the rate of energy dissipation on the intensity of interfacial mass transfer in gas-liquid dispersions.

scholarly journals ‘Tanned’ gelatin spheres and granules for exclusion chromatography

1968 ◽  
Vol 108 (4) ◽  
pp. 641-646 ◽  
Author(s):  
A. Polson ◽  
W. Katz
Keyword(s):  
Molecular Weight ◽  
Polyethylene Glycol ◽  
High Molecular Weight ◽  
Weight Fraction ◽  
High Flow ◽  
High Molecular Weight Fraction ◽  
Flow Rates ◽  
Protein Molecules ◽  
Exclusion Chromatography

1. The preparation of tanned gelatin spheres and granules from high-molecular-weight gelatin is described. This material is comparatively hard, giving high flow rates, is insoluble in water at temperatures between 0° and 100° and is resistant to digestion by trypsin and chymotrypsin. The high-molecular-weight fraction of gelatin was prepared by precipitation with polyethylene glycol, and the spheres and granules prepared from this fraction were hardened and insolubilized by tanning with either formalin or chromium salts or both. 2. The spheres and granules were used successfully for the separation of protein molecules and other protein-aceous materials ranging in molecular weight from 200 to greater than 6000000. This gel exclusion material has several properties superior to those of other products used for similar purposes. Further, it was noticed that the porosity of the spheres differed considerably from that of the granules.

scholarly journals Evaluation of a Humidified Nasal High-Flow Oxygen System, Using Oxygraphy, Capnography and Measurement of Upper Airway Pressures

2011 ◽  
Vol 39 (6) ◽  
pp. 1103-1110 ◽  
Author(s):  
J. E. Ritchie ◽  
A. B. Williams ◽  
C. Gerard ◽  
H. Hockey
Keyword(s):  
Healthy Volunteers ◽  
Airway Pressure ◽  
Gas Flow ◽  
Air Entrainment ◽  
High Flow ◽  
Positive Pressure ◽  
Mean Airway Pressure ◽  
Flow Rates ◽  
Oxygen Fraction ◽  
Airway Pressures

In this study, we evaluated the performance of a humidified nasal high-flow system (Optiflow™, Fisher and Paykel Healthcare) by measuring delivered FiO2 and airway pressures. Oxygraphy, capnography and measurement of airway pressures were performed through a hypopharyngeal catheter in healthy volunteers receiving Optiflow™ humidified nasal high flow therapy at rest and with exercise. The study was conducted in a non-clinical experimental setting. Ten healthy volunteers completed the study after giving informed written consent. Participants received a delivered oxygen fraction of 0.60 with gas flow rates of 10, 20, 30, 40 and 50 l/minute in random order. FiO2, FEO2, FECO2 and airway pressures were measured. Calculation of FiO2 from FEO2 and FECO2 was later performed. Calculated FiO2 approached 0.60 as gas flow rates increased above 30 l/minute during nose breathing at rest. High peak inspiratory flow rates with exercise were associated with increased air entrainment. Hypopharyngeal pressure increased with increasing delivered gas flow rate. At 50 l/minute the system delivered a mean airway pressure of up to 7.1 cmH2O. We believe that the high gas flow rates delivered by this system enable an accurate inspired oxygen fraction to be delivered. The positive mean airway pressure created by the high flow increases the efficacy of this system and may serve as a bridge to formal positive pressure systems.

Sign in / Sign up

Export Citation Format

Share Document