Manufacturing of polymer/metal composites by fused deposition modeling process with polyethylene

2019 ◽  
Vol 137 (21) ◽  
pp. 48717 ◽  
Author(s):  
Mojtaba Nabipour ◽  
Behnam Akhoundi ◽  
Arvin Bagheri Saed
Keyword(s):  
Fused Deposition Modeling ◽  
Metal Composites ◽  
Fused Deposition ◽  
Modeling Process ◽  
Polymer Metal ◽  
Deposition Modeling

Fabrication and properties of novel polymer-metal composites using fused deposition modeling

2018 ◽  
Vol 158 ◽  
pp. 43-50 ◽  
Author(s):  
Matthew A. Ryder ◽  
Diana A. Lados ◽  
Germano S. Iannacchione ◽  
Amy M. Peterson
Keyword(s):  
Fused Deposition Modeling ◽  
Metal Composites ◽  
Fused Deposition ◽  
Polymer Metal ◽  
Deposition Modeling

scholarly journals Numerical Simulation of the Fused Deposition Modeling for the Manufacturing of Parts with both High Geometric Fidelity and Mechanical Quality

2021 ◽  
Vol 14 (6) ◽  
pp. 712-725
Author(s):  
Holm Altenbach ◽  
◽  
G´abor Janiga ◽  
Rene Androsch ◽  
Mario Beiner ◽  
...  
Keyword(s):  
Fused Deposition Modeling ◽  
Two Dimensions ◽  
Volume Of Fluid Method ◽  
Ansys Fluent ◽  
Mechanical Parts ◽  
Fused Deposition ◽  
Modeling Process ◽  
Mechanical Quality ◽  
Deposition Modeling ◽  
Manufacturing Methods

With increasing usage of additive manufacturing methods for mechanical parts the need for precise and reliable simulations of the manufacturing process increases as well. In this paper various com- putations suited for simulating the fused deposition modeling process are considered in two dimensions. In fused deposition modeling a molten polymer is laid down on a prescribed path before the cooling of the melt begins. The occuring flows are treated as multiphase flows. To model the deposition of the filament, methods of computational fluid dynamics are used in ANSYS-Fluent, namely the volume of fluid method (VOF). Different numerical experiments are simulated

Real-time distortion monitoring during fused deposition modeling via acoustic emission

2019 ◽  
Vol 19 (2) ◽  
pp. 412-423 ◽  
Author(s):  
Feng Li ◽  
Zhonghua Yu ◽  
Zhensheng Yang ◽  
Xuanwei Shen
Keyword(s):  
Acoustic Emission ◽  
Real Time ◽  
Acoustic Emission Signal ◽  
Fused Deposition Modeling ◽  
Emission Signal ◽  
Fused Deposition ◽  
Modeling Process ◽  
Deposition Modeling ◽  
Part Distortion ◽  
Quality Diagnosis

Fused deposition modeling is a popular technique for three-dimensional prototyping since it is cost-effective, convenient to operate, and environment-friendly. However, the low quality of its printed products jeopardizes its future development. Distortion, also known as warping deformation, which is caused by many factors such as inappropriate process parameters and process drifts, is one of the most common defects in the fused deposition modeling process. Rapid detection of such part distortion during the printing process is beneficial for improving the production efficiency and saving materials. In this article, a real-time part distortion monitoring method based on acoustic emission is presented. Our work is to identify distortion defects and understand the condition of the distortion area through sensing and digital signal processing techniques. In our experiments, both the acoustic emission hits and original signals were acquired during the fused deposition modeling process. Then, the acoustic emission hits were analyzed. Ensemble empirical mode decomposition was utilized to eliminate noise and extract features from the original acoustic emission signal to further analyze the acoustic emission signal in the case of part distortion. Furthermore, the root mean square of the reconstructed signals was calculated, and the prediction results are strongly correlated with the ground truth printing states. This work provides a promising method for the quality diagnosis of printing parts.

Sign in / Sign up

Export Citation Format

Share Document