Analysis of network structure formed in styrene–butadiene rubber cured with sulfur/TBBS system

2006 ◽  
Vol 103 (2) ◽  
pp. 1105-1112 ◽  
Author(s):  
A. J. Marzocca ◽  
M. A. Mansilla
Keyword(s):  
Network Structure ◽  
Styrene Butadiene Rubber ◽  
Butadiene Rubber ◽  
Styrene Butadiene

Dependence of the network structure of cured styrene butadiene rubber on the sulphur content

Polymer ◽  
2004 ◽  
Vol 45 (17) ◽  
pp. 6037-6044 ◽  
Author(s):  
W. Salgueiro ◽  
A. Marzocca ◽  
A. Somoza ◽  
G. Consolati ◽  
S. Cerveny ◽  
...  
Keyword(s):  
Network Structure ◽  
Sulphur Content ◽  
Styrene Butadiene Rubber ◽  
Butadiene Rubber ◽  
Styrene Butadiene

scholarly journals The Effect of Network Structure on Compressive Fatigue Behavior of Unfilled Styrene-Butadiene Rubber

2020 ◽  
Vol 2020 ◽  
pp. 1-9
Author(s):  
Liu Yang ◽  
Kaikai Liu ◽  
Aihua Du
Keyword(s):  
Fatigue Resistance ◽  
Network Structure ◽  
Fatigue Behavior ◽  
Surface Damage ◽  
Styrene Butadiene Rubber ◽  
Butadiene Rubber ◽  
Cyclic Compression ◽  
Before And After ◽  
Styrene Butadiene ◽  
Compressive Resistance

The effect of network structure on dynamic compressive fatigue behavior and static compressive mechanical properties of styrene-butadiene rubber (SBR) were investigated. A series of SBR compounds with different amounts of sulfur and dicumyl peroxide (DCP) were prepared, and their crosslinking densities were calculated using the Flory–Rehner equation. Compressive fatigue resistance and creep behavior of the vulcanizates were performed on a mechanical testing and simulation (MTS) machine. The fatigue damage surface of SBR vulcanizates before and after a dynamic compressive fatigue test was observed with a scanning electron microscopy (SEM). The results suggested that the surface of the samples was badly damaged as the number of compressive cycles increased. By comparison, compressive fatigue caused less surface damage to sulfur-cured SBR than to peroxide-cured SBR. The peroxide-cured SBR samples showed higher energy dissipation than sulfur-cured SBR during cyclic compression. The peroxide-cured SBR showed lower creep strain and compression set than the sulfur-cured SBR. The -Sx- linkages provided by the sulfur curing system allow dynamic compressive deformation but suffer from poor static compressive resistance. However, the carbon-carbon linkages from DCP are irreversible and provide higher resistance to static compressive stress, but they do not show obvious dynamic compressive fatigue resistance.

CORRELATION OF FILLER NETWORKING WITH REINFORCEMENT AND DYNAMIC PROPERTIES OF SSBR/CARBON BLACK/SILICA COMPOSITES

2015 ◽  
Vol 88 (4) ◽  
pp. 676-689 ◽  
Author(s):  
Wengjiang Feng ◽  
Zhenghai Tang ◽  
Peijin Weng ◽  
Baochun Guo
Keyword(s):  
Carbon Black ◽  
Network Structure ◽  
Dynamic Properties ◽  
Rolling Resistance ◽  
Styrene Butadiene Rubber ◽  
Butadiene Rubber ◽  
Rubber Composites ◽  
Filler Network ◽  
Improved Performance ◽  
Styrene Butadiene

ABSTRACT The use of silica to partially replace carbon black is a common practice in the fabrication of “green tires.” Although some degree of consensus has been approached concerning the improved performance conferred by silica substitution, such as the improved dispersion of carbon black, a quantitative understanding of the relationship between filler networking and the performance of rubber composites has not been established. Thus, an investigation focusing on filler network structure and the correlation between the network structure and the reinforcement of rubber composites was conducted. We prepared solution-polymerized styrene–butadiene rubber (SSBR) reinforced by carbon black and carbon black/silica in different ratios. To exclude as much of the effect from changed crosslinking, and figure out how filler blending influences filler dispersion and filler network structure, the silane generally used in the tire industry was not adopted. The quantitative predictor, the mass fractal dimension df, was derived from the Kraus model and the Huber–Vilgis model. We found that when the amount of substituted silica increases, the filler cluster branching decreases, accompanied by increased reinforcement efficiency. The depressed filler networking induced by silica substitution at an appropriate proportion leads to improved dynamic properties, including lower rolling resistance and better wet skid. When the silica proportion in the filler is too high, severe filler networking is observed, resulting in decreased reinforcing efficiency and impaired dynamic properties.

Effects of White Rot Fungus Physisporinus sp., Isolated in Japan, on Styrene-butadiene Rubber

2020 ◽  
Vol 93 (9) ◽  
pp. 289-292
Author(s):  
Yumi SHIMIZU ◽  
Shuma SATHO ◽  
Taro NAKAJIMA ◽  
Hiroaki KOUZAI ◽  
Kiminori SHIMIZU
Keyword(s):  
White Rot ◽  
White Rot Fungus ◽  
Styrene Butadiene Rubber ◽  
Butadiene Rubber ◽  
Styrene Butadiene
Sign in / Sign up

Export Citation Format

Share Document