Effects of the combination of solid lubricants and short carbon fibers on the sliding performance of poly(ether imide) matrix composites

2004 ◽  
Vol 94 (4) ◽  
pp. 1428-1434 ◽  
Author(s):  
Guijun Xian ◽  
Zhong Zhang
Keyword(s):  
Carbon Fibers ◽  
Solid Lubricants ◽  
Matrix Composites ◽  
Short Carbon

scholarly journals Microstructure and mechanical properties of short-carbon-fiber/Ti3SiC2 composites

2020 ◽  
Vol 9 (6) ◽  
pp. 716-725
Author(s):  
Guangqi He ◽  
Rongxiu Guo ◽  
Meishuan Li ◽  
Yang Yang ◽  
Linshan Wang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Carbon Fiber ◽  
Flexural Strength ◽  
Carbon Fibers ◽  
Vickers Hardness ◽  
Matrix Composites ◽  
Transition Layers ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Short Carbon

AbstractShort-carbon-fibers (Csf) reinforced Ti3SiC2 matrix composites (Csf/Ti3SiC2, the Csf content was 0 vol%, 2 vol%, 5 vol%, and 10 vol%) were fabricated by spark plasma sintering (SPS) using Ti3SiC2 powders and Csf as starting materials at 1300 °C. The effects of Csf addition on the phase compositions, microstructures, and mechanical properties (including hardness, flexural strength (σf), and KIC) of Csf/Ti3SiC2 composites were investigated. The Csf, with bi-layered transition layers, i.e., TiC and SiC layers, were homogeneously distributed in the as-prepared Csf/Ti3SiC2 composites. With the increase of Csf content, the KIC of Csf/Ti3SiC2 composites increased, but the σf decreased, and the Vickers hardness decreased initially and then increased steadily when the Csf content was higher than 2 vol%. These changed performances (hardness, σf, and KIC) could be attributed to the introduction of Csf and the formation of stronger interfacial phases.

scholarly journals Investigation on microstructure and mechanical properties of short-carbon-fiber/Ti3SiC2 composites

2020 ◽  
Author(s):  
Guangqi He ◽  
Rongxiu Guo ◽  
Meishuan Li ◽  
Yang Yang ◽  
Linshan Wang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Carbon Fiber ◽  
Flexural Strength ◽  
Carbon Fibers ◽  
Matrix Composites ◽  
Transition Layers ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Short Carbon

Abstract In this paper, short-carbon-fibers (Csf) reinforced Ti3SiC2 matrix composites (Csf/Ti3SiC2, the Csf content was 0, 2, 5 and 10 vol.%) were fabricated by spark-plasma-sintering (SPS) using Ti3SiC2 powders and Csf as starting materials at 1300 oC. The effects of Csf addition on the phase compositions, microstructures and mechanical properties (including hardness, flexural strength and fracture toughness) of Csf/Ti3SiC2 composites were investigated. The Csf, with a bi-layered transition layers, i.e. TiC and SiC layer, were homogeneously distributed in the as-prepared Csf/Ti3SiC2 composites. With the increase of Csf content, the fracture toughness of Csf/Ti3SiC2 composites increased, but the flexural strength decreased, while the Vickers hardness decreased initially then increased steadily when the Csf content was higher than 2 vol.%. These changed performances could be attributed to the introduction of Csf and the formation of much stronger interfacial phases.

Surface Modification of Short Carbon Fibers with Carbon Nanotubes to Reinforce Epoxy Matrix Composites

2018 ◽  
Vol 18 (7) ◽  
pp. 4940-4952 ◽  
Author(s):  
Luo Zhanjun ◽  
Chen Hui ◽  
Wu Jing ◽  
Xia Xiaohong ◽  
Liu Hongbo ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Surface Modification ◽  
Carbon Fibers ◽  
Epoxy Matrix ◽  
Matrix Composites ◽  
Short Carbon

Wear and Mechanical Properties of Short Carbon Fiber Reinforced Copper Matrix Composites

2011 ◽  
Vol 474-476 ◽  
pp. 1605-1610 ◽  
Author(s):  
Lian Wei Yang ◽  
Yun Dong ◽  
Rui Jie Wang
Keyword(s):  
Mechanical Properties ◽  
Carbon Fiber ◽  
Carbon Fibers ◽  
Adhesive Wear ◽  
Copper Matrix ◽  
Matrix Composites ◽  
Fiber Reinforced ◽  
Short Carbon Fiber ◽  
Copper Matrix Composites ◽  
Short Carbon

The mechanical properties and wear behavior of short carbon fiber reinforced copper matrix composites was studied. In order to avoid any interfacial pronlems in the carbon fibre reinforced composites, the carbon fibers were coated with copper. The fibers were coated by electroless coating method and then characterized. Composites containing different amounts of carbon fibers were prepared by hot pressing technique. The results show that Carbon fiber/Cu–Ni–Fe composites showed higher hardness, higher wear resistance and bending strength than the common copper alloy when carbon fibers content is less than 15 vol.%. The predominant wear mechanisms were identified as adhesive wear in the alloy and adhesive wear accompanied with oxidative wear in the 12 vol.% carbon fiber/Cu–Ni–Fe composites.

Fabrication and properties of short carbon fibers reinforced copper matrix composites

2007 ◽  
Vol 43 (3) ◽  
pp. 974-979 ◽  
Author(s):  
Lei Liu ◽  
Yiping Tang ◽  
Haijun Zhao ◽  
Jianhua Zhu ◽  
Wenbin Hu
Keyword(s):  
Carbon Fibers ◽  
Copper Matrix ◽  
Matrix Composites ◽  
Copper Matrix Composites ◽  
Short Carbon

Structural and Thermal Properties of Hot Pressed Cu/C Matrix Composites Materials Used for the Thermal Management of High Power Electronic Devices

2007 ◽  
Vol 534-536 ◽  
pp. 1505-1508 ◽  
Author(s):  
Pierre Marie Geffroy ◽  
Jean François Silvain
Keyword(s):  
Thermal Conductivity ◽  
Thermal Properties ◽  
Carbon Fibers ◽  
Volume Fraction ◽  
Coefficient Of Thermal Expansion ◽  
Copper Matrix ◽  
Matrix Composites ◽  
Porosity Level ◽  
Materials Used ◽  
Short Carbon

In order to obtain materials for electronic applications that exhibit both excellent thermal conductivity and low coefficient of thermal expansion (CTE), copper matrix composites have been reinforced by short high modulus graphite fibers. The lack of fiber/matrix interaction prevents any degradation of the carbon reinforcement during the elaboration steps and the normal use of these materials. Elaboration conditions, such as mixing conditions of the short carbon fibers and the copper powder, dimension and shape of the two powders, and finally densification atmosphere, temperature, pressure and time, have been optimized. Main parameters involved in the thermal properties of the Cu/C composite materials have been analyzed and adjusted. CTE is mainly related with the carbon volume fraction; CTE ranging from 9 to 13 10-6/°C can be reproductively obtained with carbon volume fraction ranging from 50% to 20%. Thermal conductivity properties are more complex and are linked mainly with 1) the porosity level inside the material, and 2) the orientation, properties and volume fraction of the carbon fibers. For short carbon fibers, in plane thermal conductivity ranging from 200 to 550 W/mK have been reproductively measured associated with thermal conductivity through-thickness ranging from 150 to 300 W/mK.

scholarly journals Investigation on microstructure and mechanical properties of short-carbon-fiber/Ti3SiC2 composites

2020 ◽  
Author(s):  
Guangqi He ◽  
Rongxiu Guo ◽  
Meishuan Li ◽  
Yang Yang ◽  
Linshan Wang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Carbon Fiber ◽  
Flexural Strength ◽  
Carbon Fibers ◽  
Matrix Composites ◽  
Transition Layers ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Short Carbon

Abstract In this paper, short-carbon-fibers (Csf) reinforced Ti3SiC2 matrix composites (Csf/Ti3SiC2 , the Csf content was 0, 2, 5 and 10 vol.%) were fabricated by spark-plasma-sintering (SPS) using Ti3SiC2 powders and Csf as starting materials at 1300 ℃. The effects of Csf addition on the phase compositions, microstructures and mechanical properties (including hardness, flexural strength and fracture toughness) of Csf/Ti3SiC2 composites were investigated. The Csf, with a bi-layered transition layers, i.e. TiC and SiC layer, were homogeneously distributed in the as-prepared Csf /Ti3SiC2 composites. With the increase of Csf content, the fracture toughness of Csf/Ti3SiC2 composites increased, but the flexural strength decreased, while the Vickers hardness decreased initially then increased steadily when the Csf content was higher than 2 vol.%. These changed performances could be attributed to the introduction of Csf and the formation of much stronger interfacial phases.

Sign in / Sign up

Export Citation Format

Share Document