scholarly journals Hybrid Materials: An Alternative Route Towards Metal-Polymer Hybrid Materials Prepared by Vapor-Phase Processing (Adv. Funct. Mater. 16/2011)

2011 ◽  
Vol 21 (16) ◽  
pp. 3002-3002
Author(s):  
Seung-Mo Lee ◽  
Vladislav Ischenko ◽  
Eckhard Pippel ◽  
Admir Masic ◽  
Oussama Moutanabbir ◽  
...  
Keyword(s):  
Hybrid Materials ◽  
Vapor Phase ◽  
Alternative Route ◽  
Polymer Hybrid ◽  
Metal Polymer

An Alternative Route Towards Metal-Polymer Hybrid Materials Prepared by Vapor-Phase Processing

2011 ◽  
Vol 21 (16) ◽  
pp. 3047-3055 ◽  
Author(s):  
Seung-Mo Lee ◽  
Vladislav Ischenko ◽  
Eckhard Pippel ◽  
Admir Masic ◽  
Oussama Moutanabbir ◽  
...  
Keyword(s):  
Hybrid Materials ◽  
Vapor Phase ◽  
Alternative Route ◽  
Polymer Hybrid ◽  
Metal Polymer

Experimental and Numerical Studies on Dynamic Mechanical Properties of Metal-Polymer Hybrid Materials

2018 ◽  
Author(s):  
Yiben Zhang ◽  
Lingyu Sun ◽  
Lijun Li ◽  
Taikun Wang ◽  
Yantao Wang
Keyword(s):  
Mechanical Properties ◽  
Numerical Model ◽  
Strain Rate ◽  
Hybrid Materials ◽  
Dynamic Mechanical Properties ◽  
Strain Rates ◽  
Thermoplastic Polymer ◽  
Crash Simulation ◽  
Polymer Hybrid ◽  
Metal Polymer

Metal-polymer hybrid (MPH) materials can integrate the excellent mechanical properties of metal and complex geometry formability of polymer into a single component, which has become an effective way of reducing the weight of automotive semi-structural components. For example, the hybrid steel/thermoplastic polymer has been applied in automotive front-end modules, bumper cross-beams and B-pillars due to its light weight, excellent strength and stiffness, good corrosion resistance and recycling, high integration and reasonable cost. These components are usually subjected to impact or crash loads and the strain rate effect should be taken into account. This paper aims to experimentally and numerically study the dynamic behavior of MPH materials at different strain rates and provide an accurate and efficient numerical model for crash simulation of vehicles with MPH components. Firstly, MPH specimens with high strength steel (HSS) and glass fiber-reinforced thermoplastic polymer (GFRTP) were fabricated by direct injection molding adhesion (DIMA) process. Then, the dynamic mechanical properties of MPH specimens under strain rates from 800 s−1 to 2000 s−1 were investigated by Split Hopkinson Pressure Bar (SHPB) experiments. Finally, a strain rate-dependent numerical model was established in ABAQUS software to simulate the dynamic behavior of MPH specimens and validated by experimental results. Three numerical approaches for modeling the interface between the two discrete material phases were considered and compared to examine the level of interaction between two constitute materials. Cohesive zone modeling technique at the interface which saved modeling and characterization time and showed adequate predictive capability proved to be generally applicable to the evaluation of structural concepts in an early vehicle development stage. This study provides a foundation for the future engineering application of HSS/GFRP hybrid materials and numerical models for automotive crash simulation.

Surfactant-Free, Melt-Processable Metal-Polymer Hybrid Materials: Use of Graphene as a Dispersing Agent

2008 ◽  
Vol 20 (16) ◽  
pp. 3044-3049 ◽  
Author(s):  
Norman A. Luechinger ◽  
Norman Booth ◽  
Greg Heness ◽  
Sri Bandyopadhyay ◽  
Robert N. Grass ◽  
...  
Keyword(s):  
Hybrid Materials ◽  
Polymer Hybrid ◽  
Dispersing Agent ◽  
Metal Polymer

Photochemical in situ elaboration of polyoxometalate (α-[SiMo12O40]4−)/polymer hybrid materials

2013 ◽  
Vol 4 (16) ◽  
pp. 4526 ◽  
Author(s):  
Pu Xiao ◽  
Corine Simonnet-Jégat ◽  
Frédéric Dumur ◽  
Gautier Schrodj ◽  
Mohamad-Ali Tehfe ◽  
...  
Keyword(s):  
Hybrid Materials ◽  
Polymer Hybrid

Metal-polymer hybrid nanomaterial for impedimetric detection of human papillomavirus in cervical specimens

2020 ◽  
Vol 185 ◽  
pp. 113249 ◽  
Author(s):  
Karen Y.P.S. Avelino ◽  
Léony S. Oliveira ◽  
Norma Lucena-Silva ◽  
Celso Pinto de Melo ◽  
César A.S. Andrade ◽  
...  
Keyword(s):  
Human Papillomavirus ◽  
Hybrid Nanomaterial ◽  
Polymer Hybrid ◽  
Metal Polymer

AddJoining: A novel additive manufacturing approach for layered metal-polymer hybrid structures

2018 ◽  
Vol 217 ◽  
pp. 211-214 ◽  
Author(s):  
R. Falck ◽  
S.M. Goushegir ◽  
J.F. dos Santos ◽  
S.T. Amancio-Filho
Keyword(s):  
Additive Manufacturing ◽  
Hybrid Structures ◽  
Polymer Hybrid ◽  
Metal Polymer
Sign in / Sign up

Export Citation Format

Share Document